Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Ross CDA-10
Summary of Contents for Ross CDA-10
- Page 1 CHARLES ROSS & SON COMPANY INSTALLATION, MAINTENANCE AND OPERATING MANUAL DUAL SHAFT MIXER CDA-10 CHARLES ROSS & SON COMPANY 710 OLD WILLETS PATH HAUPPAUGE, NY 11788 PHONE: 631-234-0500 FAX: 631-234-0691 www.mixers.com © 2017 CHARLES ROSS & SON COMPANY...
-
Page 2: Table Of Contents
PACKING................14 E. LUBRICANTS LIST....................15 PARTS LIST - CDA-10......................16 SIDE VIEW, CDA-10 ......................18 VACUUM COVER & BEARING HOUSING VIEW - CDA-10........19 HSD BLADE VIEW - CDA-10....................20 MIX CAN VIEW - CDA-10....................21 THERMOCOUPLE ASSEMBLY, LOW PROFILE 1/8”, FLUSH MOUNT....22 APPENDIX - VENDOR PRODUCT INFORMATION............23... -
Page 3: Caution
9. Regular inspection of all moving parts, electrical wiring and safety devices should be part of regularly scheduled maintenance and daily operating procedures. 10. All state, local and national electric codes apply. 11. Lockout/disable all power to motors and controls prior to performing any maintenance. © 2017 CHARLES ROSS & SON COMPANY... -
Page 4: Initial Inspection
Since all shipments are normally shipped FOB the ROSS factory, any damage or loss is the responsibility of the carrier and should be reported to them immediately. If the terms of the sale are FOB destination, and there is damage, contact your ROSS representative or the factory immediately. -
Page 5: Safety Features
5. Emergency stop buttons. Emergency stop buttons (push/pull mushroom) are provided on all operator control panels to allow for emergency shut down of the machinery. These buttons will stop the machinery in its current position although shafts and drives will drift/coast to a stop. © 2017 CHARLES ROSS & SON COMPANY... -
Page 6: Rental Equipment
RENTAL EQUIPMENT 1. Crating. All ROSS rental equipment is shipped in reusable crates or containers made up of heavy duty skids and slatted crating. Smaller units are shipped in formed foam boxes. These crates/containers should be stored and used for the return of the rented equipment. -
Page 7: Installation
Anchor Blade OD should be relatively equally spaced from the side walls of the Mix Can when positioned at 0, 90, 180 and 270-degrees and it should be centered in the Mix Can. © 2017 CHARLES ROSS & SON COMPANY... -
Page 8: Power Requirements, Electrical Installation
If the reservoir is shipped empty it will have to be filled with the proper amount of a non-foaming hydraulic oil prior to connecting compressed air and operating the hydraulic system. Fill the reservoir to half way between the high/low marks on the dip stick. © 2017 CHARLES ROSS & SON COMPANY... -
Page 9: Mix Can
Grounding cables are recommended to be installed between the Mixer and an earthen ground to dissipate any potential static charges. Additional grounding cables should be attached from the Mixer to the Mix Can and other associated/attached equipment. © 2017 CHARLES ROSS & SON COMPANY... -
Page 10: Operation
4. Increase the mixer speed as needed, usually to maintain a vortex. - Be careful not to "over-vortex" the batch which may allow unwanted air to be incorporated. © 2017 CHARLES ROSS & SON COMPANY... -
Page 11: Vacuum Mixing
"shear zone" to prevent dusting and quick wetting of the pow- ders. Normally this is done through a valve installed in the bottom of the mixing vessel. © 2017 CHARLES ROSS & SON COMPANY... -
Page 12: Maintenance
Do not disturb the seal. If flaking persists, either the seal lip face(s) is damaged, the shaft surface is damage or the seal lip faces have dirt, debris or lubrication on them. Repeat the above procedure with new seals. For additional questions or further guidance, please contact Ross directly. © 2017 CHARLES ROSS & SON COMPANY... -
Page 13: Bearings
The gear oil in the Anchor Gear Reducer should be changed after the initial 100 hours of operation, and thereafter, at regular intervals of 2500 hours or as recommended by the manufacturer. Refer to the gear manufacturer’s manual for additional information, lubrication types and correct volume of oil. © 2017 CHARLES ROSS & SON COMPANY... -
Page 14: Hydraulic Lift Packing
Raise the cylinder and bonnet slightly off the supports and check for leaks. Tighten the packing as required. s. Remove the supports and operate the lift up and down several times. © 2017 CHARLES ROSS & SON COMPANY... -
Page 15: Lubricants List
3. Hydraulic Lift System - Any non-foaming, hydraulic oil with an ISO-ASTM viscosity grade 46 (ISO-46, AW-46) or equivalent. 4. Mechanical Seals - Non-abrasive oil with specific gravity greater than 0.8 with an ISO-ASTM viscosity grade 22 (ISO-22, AW-22) or a similar 10 weight oil. © 2017 CHARLES ROSS & SON COMPANY... -
Page 16: Parts List - Cda-10
Anchor Blade, SS Teflon Scrapers (Optional) 1 set Cover, Vacuum, SS, 10 gallon Thermoprobe, type "J" (Optional) Disperser Tower Assembly Housing, CS Safety Limit Switch & Roller Arm, Height Anchor Tower Assembly Housing, CS © 2017 CHARLES ROSS & SON COMPANY... - Page 17 Frequency Inverter, 5HP, Nema 1, 230 or 460 volt (Optional) Operator Control Station, XP or Nema 12 (Optional) - Digital Temperature Readout or Controller (Optional) - Digital Ammeter (Optional) - Digital Tachometer (Optional) Vacuum Pump (Optional) * Indicates Recommended Spare Parts © 2017 CHARLES ROSS & SON COMPANY...
-
Page 18: Side View, Cda-10
© 2017 CHARLES ROSS & SON COMPANY... -
Page 19: Vacuum Cover & Bearing Housing View - Cda-10
VACUUM COVER & BEARING HOUSING VIEW - CDA-10 © 2017 CHARLES ROSS & SON COMPANY... -
Page 20: Hsd Blade View - Cda-10
HSD BLADE VIEW - CDA-10 © 2017 CHARLES ROSS & SON COMPANY... -
Page 21: Mix Can View - Cda-10
MIX CAN VIEW - CDA-10 © 2017 CHARLES ROSS & SON COMPANY... -
Page 22: Thermocouple Assembly, Low Profile 1/8", Flush Mount
© 2017 CHARLES ROSS & SON COMPANY... -
Page 23: Appendix - Vendor Product Information
APPENDIX - VENDOR PRODUCT INFORMATION © 2017 CHARLES ROSS & SON COMPANY...
Need help?
Do you have a question about the CDA-10 and is the answer not in the manual?
Questions and answers