GPX TM45 User Manual

B
C
FULL MOTION FLAT PANEL TV MOUNT FOR 19-50" TELEVISIONS
D
User's Guide for Model No. TM45 v1382-01
E
WARNINGS
F
• The wall mounted parts of the TV mount must be firmly attached to a
concrete/brick/solid wood wall, or wall studs behind drywall. G
• Tighten screws so that the wall plate is firmly attached, but do not
overtighten. Overtightening can damage the screws and increase the H
chances of failure.
I
• Do not remove or loosen any screws until they are no longer engaged
with the mount. Doing so may cause the screen to fall.
J
• It is highly recommended to have this mount professionally installed.
• Supports VESA up to 400 x 400mm (100 x 100mm for 19" TVs).
K
• This mount is designed to hold a maximum of 66 lbs (30 kg).
L
PARTS
M
A x4
M4x15
N
B x4
M5x15
O
C x4
M6x15
P
D x4
M8x15
E x4 Q
M5x25
R
F x4
M6x25
G x4 S
M8x25
T
H x4
Ø5
I x4
Note: Parts A-L are used to attach
Ø6
your TV to the brackets in Step 4,
J x4 but you will not need all of them.
Ø8
Find and use the set that best fits
your specific TV.
K x4
Ø15xØ8x4.5
L x4
Ø15xØ8x15
M x4
Ø10x50
TOOLS
N x4
M6x50
The following tools are recommended for this installation:
O • Drill x4
M8x8
• 5/32" drill bit for drywall
P x4
M6x8
• 3/8" or 10mm drill bit for concrete
• Stud finder
Q x4
• Phillips screwdriver
R x1
S x1
Mag Level
T x1
Wrench
x4
M5x15
x4
M6x15
x4
M8x15
x4
M5x25
STEP 1
x4
M6x25
Pre-drill Holes for Articulating Swing Arm
x4
M8x25 • Drill 4 holes for the Swing Arm to attach to the wall, using exact
measurements based on where you want to mount the Articulating
Swing Arm. Only drill into a solid wall, or studs (behind drywall). DO NOT
x4
Ø5
DRILL AND HANG THE BASE PLATE ON DRYWALL OR SHEETROCK.
It is not strong enough to support a TV and will cause damage.
x4
Ø6
x4
Ø8
x4
Ø15xØ8x4.5
x4
Ø15xØ8x15
x4
Ø10x50
x4
M6x50
x4
M8x8
x4
M6x8
x4
x1
• Cutaway of drywall with studs shown behind. Use a stud finder to locate
x1
Mag Level
studs. ONLY DRILL INTO STUDS!!
• Use a 5/32" drill bit
x1
Wrench
• Concrete/Brick wall shown
• Use a 3/8" or 10mm drill bit
H x4 I
Ø5
I x4 J
Ø6
J x4 K
Ø8
K x4 L
Ø15xØ8x4.5
STEP 2
L x4 M
Attach Articulating Swing Arm to Wall Ø15xØ8x15
M x4 N
Ø10x50
N x4 O
M6x50
O x4 P
M8x8
P x4 Q
M6x8
Q x4 R
R x1 S
T
S x1
Mag Level
T x1
Wrench
• Attach the articulating swing arm to the wall. Use the included level to
ensure the arm is correctly aligned and square.
N
• Insert the four wall anchors into the holes drilled in Step 1, then screw
the base plate firmly to the wall with the supplied screws.
x4
Ø6
x4
Ø8
x4
Ø15xØ8x4.5
x4
Ø15xØ8x15
x4
Ø10x50
x4
M6x50
x4
M8x8
x4
M6x8
x4
x1
x1
Mag Level
x1
Wrench
M