Subscribe to Our Youtube Channel
Related Manuals for Power Breezer PB20-C-00-B-CE/EMI
Summary of Contents for Power Breezer PB20-C-00-B-CE/EMI
- Page 1 USER MANUAL This manual covers the following models: PB20-C-00-B-CE/EMI PB20-C-00-B PB10-C-00-B Firmware v3.4...
-
Page 2: Table Of Contents
To get the most of your Power Breezer become familiar with its features and functions described in this manual. SAVE THIS MANUAL... -
Page 3: War Nings
A. WAR NINGS • This unit is intended for use only as specified in this manual. If you have questions about its use, please contact Power Breezer. 1-844-233-5673 | customerservice@powerbreezer.com • Use only on a outlet protected by a ground-fault circuit-interrupter (GFCI). (see page 10) •... -
Page 4: Key Co Mponents
Key Components I. KEY COM PONENTS Front View Fan head Atomizer Lid latches Tie downs Transport Handle Water tank Drain plug Front casters Rear View Straps Fan head power connector Water inlet hose Atomizer drain hose Control panel Power cord Rear wheels with brake ENGLISH... - Page 5 Key Components Control Panel Power - on/off Head Rotation - on/off Atomizer (Misting) - on/off Fan Speed - up/down Storage View Dust cap Fan head support pole Tank lid Water Tank View Water valve Water tank ENGLISH...
-
Page 6: Se T Up
Setup II. S E TUP 1. Mounting the fan head: To set up your Power Breezer, you will need: • 2 people • An AC outlet (110v or 220v) • Access to water to fill the tank Remember: • Lift fan head only by the black outer shell from the top and bottom. - Page 7 Setup 3a. Lift the fan head straight up and out of the tank. Carefully rest it on the edge of the tank opposite of the fan head support pole, as shown. 3b. Adjust your grip so that each person has one hand on a strap and one hand on the bottom of the fan head.
-
Page 8: Fan Head Connections
Setup WARNING TIPPING HAZARD Once installed, the atomizer (metal disk) will be facing the tank, air will be blown over the tank NEVER install or rotate fan head so when the unit is turned on. that if faces the away from the tank. Doing so may allow the unit to become unstable and create a tipping hazard. - Page 9 Setup Remove water inlet hose from the Insert water inlet hose into front hole in the tank. bulkhead fitting. Ensure that connection is sealed. Insert atomizer drain hose into Once assembled, the atomizer the front hole on top of the tank, drain hose should be flexible, from where the water inlet hose but not so loose that water gets...
-
Page 10: Using The Correct Outlet
DO NOT plug into standard outlet without a GFCI feature. GFCI Equipped Outlet NOTE: A live power outlet can be verified when the Power Breezer is plugged in and powered off by pressing the oscillation water buttons. The LED lights will dimly illuminate when either of these buttons are depressed. -
Page 11: Adding Water To The Tank
Setup 4. Adding water to the tank: closed open Do not fill the tank above the max The water valve can be adjusted for fill level, as shown. If tank is filled optimal performance according to past this level, water may leak out of climate. -
Page 12: Oper Atio N
Operation III. OPER ATIO N 1. Control panel – Buttons: Power Oscillation Atomizer Fan Speed ENGLISH... -
Page 13: Turning On Your Unit
Operation 2. Turning on your unit: 1a. Press the power button and hold for one second. The LED light for the power button will be lit and the fan blades will begin to slowly rotate to indicate the unit is powered on. 1b. -
Page 14: Control Panel - Locking Feature
When powered back on, it will resume the same oscillation, atomizer, and fan speed settings of its last use. 6. Control panel – Dim/Brighten LED lights: The Power Breezer is equipped with a feature to dim/brighten the control panel’s LED lights: • To dim/brighten the control panel LED lights: •... -
Page 15: Disa Sse Mb Ly
LOCK position. Drain tank: Depending on volume of water to be drained, you may want to move your Power Breezer to a suitable location prior to draining. Open the drain plug by turning counter clockwise and fully drain the tank. -
Page 16: Disconnecting The Hoses
Disassembly 1. Disconnecting the hoses: Disconnect the fan head power Take atomizer drain hose out of the connector from the bulkhead front hole on top of the tank. fitting. Depress bulkhead fitting with one Store the water inlet hose in hand while pulling water inlet hose the front hole on top of tank, with the other hand to remove. -
Page 17: Dismounting Fan Head
Disassembly 2. Dismounting fan head: Unlock lid latches (4) and remove lid. Ensure both rear wheels are locked. 2a. Lift the fan head straight up 2b. Carefully rest fan head on the and off the head support pole. edge of the tank opposite of the head support pole, as shown. - Page 18 Disassembly 2c. Carefully lower the fan head Place lid on tank and lock all latches into the tank. (4). When moving unit, be sure to use the transport handle and not the head support pole. ENGLISH...
-
Page 19: T R A Nspo Rting Your Unit
Transport V. TR ANS PORT ING YO UR UNIT We recommend using tie-downs when transporting your Power Breezer to limit movement and prevent damage. For long term storage, make sure that the tank is fully dry. If it is not dry, you may use the fan to dry the tank. -
Page 20: Main Taining Your U Nit
Maintenance VI. MAINTAI NING YO UR U NIT For the best performance and longest life of your Power Breezer, we recommend the following maintenance on your unit every 30 days and prior to storing for extended periods of time. 1. Cleaning the water pump: It is important to clean the water pump. -
Page 21: Cleaning The Water System
Maintenance Remove impeller assembly and clean Reassemble water pump. with soap and water. 2. Cleaning the water system: For optimal performance of the water system, we recommend the following maintenance be performed monthly. WARNING: Once the cleaning process is started, it must be run through all steps including rinse to avoid atomizing the cleaning solution and blowing it out of the unit. -
Page 22: Maintaining The Water Tank
• If mildew develops, you can flush the system out with a little bleach (run the Power Breezer). Following the bleach treatment, flush the tank out with clean water and let air dry. -
Page 23: Maintaining The Fan Head And Motor
• When transporting over long distances, disassemble the Power Breezer and store the head in the tank to prevent damage. • NEVER move your Power Breezer by the fan head. Doing so will not only damage your unit, but it is also much more difficult to move your Power Breezer by the head than by the body. -
Page 24: T Ro Ub Les Hooting
• If the above steps fail, the pump must be replaced – contact us. 1-844-233-5673 | customerservice@powerbreezer.com Unit shuts off: • If your Power Breezer shuts off unplug it. Wait 20 seconds, then plug it back in and restart your unit. Unit will not roll: •... -
Page 25: Wa Rr A Nt Y
For two (2) years from date of shipment to the first purchaser, Breezer Holdings, LLC. (“Manufacturer”) warrants the fan, fan blades, fan motor, air straighteners and the polyethylene exterior of the Power Breezer® unit to be free from defects in materials or workmanship. Those components found, upon examination by factory-authorized personnel, to be defective in material or workmanship will be repaired or replaced with new or remanufactured parts at Manufacturer’s or authorized dealer’s option and... -
Page 26: Co Ntac T Information
Contact Information IX. CONTAC T I NFO RMAT IO N General Information or Product/Installation Support Email: customerservice@powerbreezer.com Phone: 844-233-5673 For Sales Information sales@powerbreezer.com Phone: 844-233-5673 User Videos www.youtube.com/powerbreezer www.PowerBreezer.com Follow Us www.facebook.com/PowerBreezer www.twitter.com/PowerBreezer ENGLISH... -
Page 27: Ava Il A Ble Access Ories
PB-600-005-01 Head and Tank Covers: Waterproof covers with storage bags. Protect your Power Breezer from the elements and keep your unit free from dust while in storage. Head and Tank Covers Sold independently or as a set. - Page 28 6413 Congress Avenue, Suite 110 Boca Raton, FL 33487 ©2020 Breezer Holdings, LLC. All Rights Reserved. Power Breezer® is licensed under U.S. Patent No. 6,789,787.
Need help?
Do you have a question about the PB20-C-00-B-CE/EMI and is the answer not in the manual?
Questions and answers