Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for PRO-NETS WR850RL
Summary of Contents for PRO-NETS WR850RL
- Page 1 WIRELESS 11n ROUTER WR850RL User’s Manual September 2008...
- Page 2 FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication.
- Page 3 Copyright 2008 All Rights Reserved. No part of this document can be copied or reproduced in any form without written consent from the company. Trademarks: All trade names and trademarks are the properties of their respective companies. Revision History Revision History Release You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your...
-
Page 4: Table Of Contents
Table of Contents 1. Introduction ..................5 1.1 Features ...................... 5 1.2 Package Contents..................6 1.3 System Requirements ................6 1.4 LEDs Indication & Connectors of Wireless Router ........ 6 1.5 Installation Instruction ................7 2. PC Configuration................8 2.1 TCP/IP Networking Setup................8 3. - Page 5 3.7.2 Upgrade Firmware ............... 54 3.7.3 Setting Management..............55 3.7.4 Status .................... 56 3.7.5 Statistics ..................57 3.7.6 System Command ............... 58 3.7.7 System Log .................. 59...
-
Page 6: Introduction
1. Introduction This Wireless Broadband Router is a draft 802.11n compliant device that provide faster and farther range than 802.11g while backward compatible with 802.11g and 802.11b devices. This Router uses advanced broadband router chipset and wireless LAN chipset solution let you enjoy high-speed Wired and Wireless connection. -
Page 7: Package Contents
1.2 Package Contents One Wireless AP Router with 2 antennas One External Power Adapter One CD-ROM (user’s manual) One RJ-45 Ethernet Cable 1.3 System Requirements Computers with an installed Ethernet adapter. Valid Internet Access account and Ethernet based DSL or Cable modem. 10/100Base-T Ethernet cable with RJ-45 connector. -
Page 8: Installation Instruction
Back Panel Connectors Button/Port Description Reset Reset configurations to default. You would use the reset button only when a program error has caused your 11n AP router to hang. Press the button and hold for 10 seconds. Click WPS button about 2-3 seconds while you are connecting a PC of wireless adapter with WPS function (you must enable WPS’... -
Page 9: Pc Configuration
2. PC Configuration To communicate and configure 802.11n AP router, the PC on your LAN must install TCP/IP protocol. Make sure the TCP/IP protocol of the PC is configured for Obtain IP address from DHCP and is connected to LAN (Ethernet) port of the AP router. In doing so, the PC obtains an IP address of 192.168.1.1 from 802.11n AP router. - Page 10 Click “Properties”, the window below will appear and then click “IP Address” tab, If you decide to use DHCP, select “Obtain an IP address automatically”, then click “OK” to confirm your settings. Once you restart your system, Wireless Router will obtain an IP address for this system. If you decide to use fixed IP address for your system, select “Specify an IP address”, and make sure that IP Address and Subnet Mask are correct.
- Page 11 Select “DNS Configuration” tab and make sure select “Enable DNS”, enter the DNS address provides from your ISP in the “DNS Server Search Order” field, then click “Add”,...
- Page 12 Checking TCI/IP Setting for Windows NT4.0 Select “Control Panel Æ Network”, window below will appear, click “Protocols” tab then select “TCP/IP protocol”, Click “Properties”, window below will appear.
- Page 13 Select the network card on your system from “Adapter” field. If you decide to use IP address from Wireless Router, select “Obtain an IP address from a DHCP server”. If you decide to use the IP address you are desired, select “Specify an IP address”.
- Page 14 Select the “Internet Protocol (TCP/IP)” for the network card on your system, then click “Properties”, window below will appear.
- Page 15 If you decide to use IP address from Wireless Router, select “Obtain an IP address automatically”. If you decide to use the IP address you are desired, select “Use the following IP address”. Make sure enter correct addresses in “IP Address” and “Subnet Mask”...
- Page 16 If you decide to use IP address from Wireless Router, select “Obtain an IP address automatically”. If you decide to use the IP address you are desired, select “Use the following IP address”. Make sure enter correct addresses in “IP Address” and “Subnet Mask”...
- Page 17 Select “Internet Protocol (TCP/IP)” then click “Properties”, window below will appear.
-
Page 18: Configure Wireless Router Via Web Based Utility
If you decide to use IP address from Wireless Router, select “Obtain an IP address automatically”. If you decide to use the IP address you are desired, select “Use the following IP address”. Make sure enter correct addresses in “IP Address” and “Subnet Mask”... -
Page 19: Operation Mode
Step3: After log in, you can see the Main menu as below. 3.2 Operation Mode In this option, you can configure the operation mode which suitable for your environment. The default setting is Gateway. There have three modes is provided: -- Bridge: All Ethernet and wireless interfaces are bridged into a single bridge interface. - Page 20 -- Gateway: The first Ethernet port is treated as WAN port. The other Ethernet ports and the wireless interface are bridge together and are treated as LAN ports. -- Ethernet Converter: The wireless interface is treated as WAN port and the Ethernet ports are LAN ports.
Need help?
Do you have a question about the WR850RL and is the answer not in the manual?
Questions and answers