Table of Contents
Advertisement
en Basic operation
As soon as the ventilation time ends, the LED for the
fan setting you have selected goes out. LED 6 contin-
ues to flash.
8.11 Sensor control
In automatic mode, a sensor in the appliance detects
the intensity of the cooking and roasting fumes. De-
pending on the setting of the sensor sensitivity, the op-
timum fan setting is automatically switched on.
If the sensor control system reacts too weakly or too
strongly, the setting for the sensor sensitivity may
change.
¡ Default setting: Fan setting 3
¡ Lowest setting: Fan setting 1
¡ Highest setting: Fan setting 5
8.12 Setting the sensor control
Requirement: The appliance is switched off.
1.
Press and hold
and
Press
or
to change the setting.
2.
To cancel the setting, press .
To save the setting, press and hold
3.
prox. 3 seconds.
Or wait approx. 10 seconds until the setting is
saved automatically.
a A signal tone sounds as soon as the selected set-
ting is saved.
8.13 Setting the saturation indicator
The saturation indicator must be adjusted depending
on the filter used.
Requirement: The appliance is switched off.
Press and hold
and
1.
To set circulating-air mode (non-regenerable fil-
‒
ter), press
/
until LED 2 lights up in the LED
display.
To set circulating-air mode (non-regenerable fil-
‒
ter), press
/
until LED 3 lights up in the LED
display.
To convert the electronic control back to opera-
‒
tion without the air recirculation filter, press
until LED 1 lights up on the LED display.
To save the setting, press and hold and for ap-
2.
prox. three seconds.
Or wait approx. 10 seconds until the setting is
saved automatically.
To cancel the setting, press .
a A signal tone sounds as soon as the selected set-
ting is saved.
8.14 Resetting the saturation indicator
After cleaning the grease filter or after changing the
odour filter, the saturation indicator can be reset.
Requirements
¡ After the appliance has been switched off, LED 1
flashes in the LED display for the grease filter satura-
tion display and/or LED 2 flashes for the saturation
indicator for the odour filter.
¡ A repeated signal tone sounds.
1
Depending on the appliance specifications
8
1
1
for approx. 3 seconds.
and
for approx. three seconds.
Press
▶
a The saturation indicator is reset.
8.15 Switching on the lighting
The lighting can be switched on or off independently of
the ventilation.
Press
▶
Note: Colour temperature settings are available in the
Home Connect app provided the appliance has this
function.
8.16 Setting the brightness
Press and hold
▶
Note: Colour temperature settings are available in the
Home Connect app provided the appliance has this
function.
8.17 Switching on the button tone
The button tones can be switched on.
Requirement: The appliance is switched off.
for ap-
Press and hold
1.
a In the LED display, the LED for the setting that is
currently selected lights up.
Press
2.
play.
To cancel the setting, press .
To save the setting, press and hold
3.
prox. three seconds.
Or wait approx. 10 seconds until the setting is
saved automatically.
a A signal tone sounds as soon as the selected set-
ting is saved.
8.18 Switching the button tone off
The button tones can be switched off.
Note: Signal tones for the appliance are always
switched on and cannot be switched off.
Requirement: The appliance is switched off.
/
Press and hold
1.
a In the LED display, the LED for the setting that is
currently selected lights up.
Press
2.
play.
To cancel the setting, press .
To save the setting, press and hold
3.
prox. three seconds.
Or wait approx. 10 seconds until the setting is
saved automatically.
a A signal tone sounds as soon as the selected set-
ting is saved.
.
.
or .
and
for approx. three seconds.
or until LED 1 lights up in the LED dis-
and
for approx. three seconds.
or until LED 2 lights up in the LED dis-
and
for ap-
and
for ap-
Advertisement
Table of Contents
