AV NVR AV800-2T1 Quick Start Manual

Quick Start Guide

█ Hardware Overview

No. LEDs Status
Power Solid Light Power on
Solid Light HDD functioning properly
Disk Blinking Failed HDD
Off No HDD/ HDD is offline
1
Solid Light Operating properly
Blinking Restore factory default process/
( 100ms On/Off ) Firmware update
Status
Continuous Blinking
Failed firmware update
(1000ms On/Off)
Alarm Blinking System/Camera event occurs
No. Buttons Status
Stop Press to stop a buzzer
2 Mute
Restore display
Press and hold for 5 seconds
defaults
On Press and hold for 1 second
3 Record
Off Press and hold for 1 second
Restore default Press and hold for 10 seconds
4 Reset
Restart Press and hold for 1 second
On/ Off Press and hold for 1 second
5 Power
HW Force Off Press and hold for 10 second
No. Interfaces
6 USB 2x USB 2.0
7 PoE
PoE network interfaces
8 Ethernet RJ-45 10M / 100M / 1000M
9 Audio Input 1-Ch, RCA
10 Audio Output
RCA
11 VGA VGA output connector
12 HDMI HDMI output connector
13 USB 1x USB 3.0
14 Power Switch Power on /off
15 Power In 100~240V AC, 50/60Hz

█ Preparation

1. If you would like to install HDDs or expand your HDD capacity, please refer to "HDD
installation" section.
2. Connect supplied AC power cord to the power input (#15) on the NVR
3. Connect a Cat 5e cable to the LAN 1 port (#8) on the NVR
4. Connect a monitor to the HDMI (#12) or VGA (#11) interface on the NVR.
5. Connect supplied mouse to the USB port (#6 or #13) on the NVR
6. Connect your Audio in/ out devise to the Audio In (#9) / Out (#10) interface on the AV
NVR.

█ HDD Installation

1. Unscrew the two screws from the AV NVR cover
Definitions
2. Connect SATA Power cable and SATA Data cable on the AV NVR's main board, and
install HDDs on the NVR by securely fastening the four screws on each HDD.
Procedure
3. Connect SATA Power cable and SATA Data cable to the HDD.
4. Re-install the AV NVR cover and securely fasten the six screws

█ Power on the NVR

Definitions
1. Plug AC power cord into 100 to 240V AC outlet.
2. Turn power switch (#15) on.
3. Click power button (#5)
4. Power indicator (#1) should show a solid light.

█ Connect to the NVR

1. Use default IP address, 192.168.101.50, to connect to the AV NVR
2. Use the default username "admin" and password "admin" to login to the AV NVR.
NOTE: It's highly recommended that you change the password during initial setup.
NOTE: You can have 4 to 31 characters including upper and lower case letters, digits for both
User Name and Password, and only allow four symbols: ".", "@", "_", "-" .
AV NVR
PoE Network Video Recorder

█ (If needed) Format HDD

Visit Settings
HDD.
█ Set Time & Date
Visit Settings

█ Set Network Settings

1. Visit Settings
2. Select "Auto-Configure as DHCP Server" if you would like to enable DHCP.

█ Connect IP cameras

1. Plug cameras into PoE ports (#7)
NOTE: This product supports Smart Plug-and-Play, so cameras should be set up and
configured automatically in couple minutes.
2. SurroundVideo and MicroDome Duo cameras will take four and two channels, so
please make sure plug the next camera into the following ports. For example, if
one SurroundVideo camera plugs into Port#1, the next camera should plug into
Port#5 since the SurroundVideo camera has taken Channel#1, #2, #3, and #4.
3. ( If necessary) Visit Settings
4. ( If necessary) Add cameras by "Auto Search" or "Manually".
█ Recording & Scheduling
1. The default setting for all channels is Event Record at all times.
2. ( If necessary) Visit Settings
3. ( If necessary) Visit Settings
NOTE: For more advanced video parameter settings, you will need
to visit the camera's web interface. To do so you need to connect
your laptop/PC directly to the PoE ports.
> Storage> Storage Status, and click "Format" to initialize the
> Time & Date
> Network Settings
> Channel
> Recording to update the settings
> Scheduling to update the settings