Related Manuals for CNH CASE CONSTRUCTION CX350D
Summary of Contents for CNH CASE CONSTRUCTION CX350D
- Page 1 CX350D CX370D Crawler Excavator SERVICE MANUAL Part number 47843027 English May 2015 © 2015 CNH Industrial Italia S.p.A. All Rights Reserved.
- Page 2 SERVICE MANUAL CX350D Crawler excavators LC version (TIER4 FINAL) - EU Market CX350D Crawler excavators NLC version (TIER4 FINAL) - EU Market CX370D Crawler excavators LC version (TIER4 FINAL) - EU Market CX370D Crawler excavators NLC version (TIER4 FINAL) - EU Market 47843027 21/05/2015...
- Page 3 Contents INTRODUCTION Engine..................10 [10.001] Engine and crankcase ............. 10.1 [10.102] Pan and covers .
- Page 4 [35.359] Main control valve ..............35.6 [35.357] Pilot system .
- Page 5 Thanks very much for your reading, Want to get more information, Please click here, Then get the complete manual NOTE: If there is no response to click on the link above, please download the PDF document first, and then click on it. Have any questions please write to me: admin@servicemanualperfect.com...
- Page 6 [55.302] Battery................55.7 [55.202] Cold start aid .
- Page 7 [90.150] Cab ................. 90.1 [90.156] Cab glazing .
- Page 8 47843027 21/05/2015...
- Page 9 INTRODUCTION 47843027 21/05/2015...
- Page 10 Contents INTRODUCTION Foreword - Important notice regarding equipment servicing ........3 Safety rules .
- Page 11 INTRODUCTION Foreword - Important notice regarding equipment servicing All repair and maintenance work listed in this manual must be carried out only by qualified dealership personnel, strictly complying with the instructions given, and using, whenever possible, the special tools. Anyone who performs repair and maintenance operations without complying with the procedures provided herein shall be responsible for any subsequent damages.
- Page 12 INTRODUCTION Safety rules Personal safety This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible death or injury. Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special in- structions.
- Page 13 INTRODUCTION Safety rules – General information Cleaning Clean the metal parts with cleaning solution that meets the standard and steam cleaning. (except for bearings) After cleaning, dry well, and inject oil in all parts. Also inject oil into the bearings after drying. Inspection When disassembling parts, check all the parts.
- Page 14 INTRODUCTION Safety rules – Personal safety WARNING: This symbol indicates a precaution. It gives information concerning the safety of the operator and those in the surroundings. Read and understand these precautions thoroughly before performing the work. Always comply with warnings and precautions so as to avoid any accidents. This section covers information related to overall safety.
- Page 15 INTRODUCTION WARNING: Check that there is no one in the surroundings before draining the pressure from hydraulic circuits during machine hydraulic cylinder inspection. WARNING: Use gloves when handling high-temperature parts. WARNING: Bring the lower parts or attachments in contact with the ground before inspecting or repairing them. WARNING: Check that hoses and tubes are securely connected.
- Page 16 INTRODUCTION Safety rules – ROPS judgment 1. Purpose Judge whether or not the model is compliant with ROPS by the ROPS criteria. Compliance with ROPS is highly dependent on its deadweight and boom. The model has passed the ROPS test for its deadweight with all selectable options installed (as of 2014). However, the judgment is required because its deadweight or boom position may go beyond the assumption de- pending on derivative or order conditions.
- Page 17 INTRODUCTION It is not applicable if the position overlapping with a cab on the side view (mark * in the figure) is lowered significantly as compared with the standard model (standard arm), within the maximum digging radius with the bucket tip on the surface of the ground.
- Page 18 INTRODUCTION Cab (CX210D/CX250D/CX300D) SMIL14CEX2002FA 47843027 21/05/2015...
- Page 19 INTRODUCTION Cab (CX350D/CX370D) The large-sized model (CX350D/CX370D) cab consists of the medium-sized model (CX210D/CX250D/CX300D) cab in the figure plus seven reinforcements. SMIL14CEX2003FA The high cab is not supported basically. (Since it varies for each model, consultation with us is required in each case.) 47843027 21/05/2015...
- Page 20 INTRODUCTION Torque – Bolt and nut • Tighten alternating between left and right and top and bottom so that uniform tightening force is applied. LPIL12CX00005EA • If L ® was used on a removed bolt (there is something white sticking to the bolt when it is removed), clean the OCTITE old L ®...
- Page 21 INTRODUCTION Torque – Special torque setting Nominal bolt Retightening location Tightening torque Code Wrench diameter 900 - 1051 N·m (664 - 775 lb ft) Travel motor 36 mm Drive sprocket 521 - 608 N·m (384.27 - 448.44 lb ft) 30 mm Take-up roller 24 mm 267 - 312 N·m (196.93 - 230.12 lb ft)
- Page 22 INTRODUCTION SMIL14CEX2929HB 47843027 21/05/2015...
Need help?
Do you have a question about the CASE CONSTRUCTION CX350D and is the answer not in the manual?
Questions and answers