Warning This equipment complies with CE radiation exposure limits set forth for anuncontrolled environment. This eq uipment should be installed and operated withminimum distance 20cm between the radiator & your body. Restrictions in the 5 GHz band According to Article 10 (10) of Directive 2014/53/EU, the packaging shows that this radio equipment will be subject to some restrictions when placed on the market in Belgium (BE), Bulgaria (BG), the Czech Republic (CZ), Denmark (DK), Germany (DE), Estonia (EE), Ireland (IE), Greece (EL), Spain (ES), France (FR), Croatia (HR), Italy (IT), Cyprus (CY), Latvia (LV), Lithuania (LT), Luxembourg (LU), Hungary (HU), Malta...
DECLARATION OF CONFORMITY Applier certifies that the following designated product Product Name: Mobile DVR Model No.: LZE500 Is in conformity with the standard(s) EN60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013 EN62311:2008 Draft ETSI EN301489-1 V2.2.1 Draft ETSI EN 301 489-17 V3.2.0 Draft ETSI EN301489-19 V2.1.0 Draft ETSI EN301489-52 V1.1.0 EN303 413 V1.1.1...
Page 5
The device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range. 5 / 19...
Chapter 1 Product Introduction 1.1 About E500 LZE500 Mobile DVR is a compact, full-featured recording system that uses SD card, hard disk (HDD) and solid state disk (SSD) as the storage device. It provides H.264 high-quality and max 8 channels of 720P/1080P AHD recording, and 8 channels of 720P/1080P high definition video surveillance and fleet management for police car, ambulance, fire engine, public buses, tourist buses, etc.
1.4 Front Panel Item Interface Function For Display “MANU”,“▲”,“▼”,“OK” Button Button Indicates the device power-on and wireless network connection status; WORK Red LED Fast flash: device registration network Slow flash: The device is registered on the network. Indicating GPS/BDS positioning signal receiving status; Green LED Fast flash: device is not positioned Slow flash: The device is positioned...
Flashing: IPC Ethernet has data transmission and reception IPC2 indicator; Light off: IPC is not connected IPC2 Green LED Light on: IPC Ethernet is connected Flashing: IPC Ethernet has data transmission and reception USB Interface Local upgrade CPU serial port print information, Can be used for debug Debugging upgrade...
Network 1-CH RJ45 Ethernet converter interface 1-CH USB, type A Input Power DC 9V ~ 36V, typical 12V/24V Power Output-1 +5V@2A POWER SUPPLY Power Output-2 8CH +12V@500mA (analog cameras) Power Output-3 2CH +12V@500mA (IP cameras) Power Consumptions <25W (not connect with accessories and HDD/SSD) Operating Temperature -20º...
Page 11
Please use a 2.5-inch hard drive and purchase it from a regular store to ensure the quality of the hard drive. After the hard disk is installed, you need to format it before you can record it, otherwise the system will judge the hard disk error.
2.3 Wiring Diagram 2.4 Interface 2.4.1 4G Antenna The interface standard of the antenna port is SMA male External Antenna Antenna gain: 3.5 dBi 14 / 19...
Page 15
2.4.2 GPS Antenna The GPS antenna adopts the standard SMA interface. The curved side of the GPS antenna is facing upwards, and the flat side is facing downward. The fixed position must make the arc of the antenna face the sky, and there should be no obstruction on the upper side.
Page 16
2.4.4 Power The following picture shows the 5-pin power cable, 5-pin connector to connect the device power interface, bare wire part: the red wire is connected to the positive pole, the black wire is grounded, and the yellow wire is connected to the ACC (required) 2.4.5 10-PIN Console Can transfer speakers, microphone, Driver console;...
Page 17
2.4.7 SIM Card Installation To purchase a SIM/UIM card from a telecom carrier, the card must be opened for data services; if voice calls are required, voice services must be activated. Remove the SIM card slot and insert the SIM/UIM card as shown below. Note that the side of the chip is facing down.
Page 20
FCC Caution. (1)§ 15.19 Labelling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. §...
Need help?
Do you have a question about the LZE500 and is the answer not in the manual?
Questions and answers