Verizon WPS100 Instruction Manual

W
ireless Touchless Switch (WPS100)
Instruction Manual
The WPS100 is a wireless proximity switch that is easy to install. It can control the opening and closing of automatic doors
and similar devices by detecting hand or object movement without direct contact. For the safe and correct use of the product,
please read this instruction manual carefully.
1
Product composition and specification
WPS100
Double-sided Tape
Battery (CR123A)
Fixing Screw (4 * 16)
Front Plate (2 types)
User Manual
Power Supply
Technology
Detection Range / Method
Detecting Target
Output
Transmitting distance
Reaction sensitivity
Battery Lifespan
Current Consumption
Operating Temp / Humidity
International Protection
Product size / weight
2
General Information
LED Red : Detecting
LED Red : Replace battery
(Battery symbol will flash 5 times after detecting)
95
Detection LED
Battery replacement LED
Light emitting sensor
LED / Buzzer Switch
ON/OFF Switch
1EA
1EA
2EA
2EA
2EA (Hand and Wheelchair)
1Copy
DC3V
Infrared - Reflective
1~15cm ±5cm / LED or BUZZER
Hand or Object (Touchless)
※ Detecting distance varies depending on the color of the object
2.4GHz
<10m (2m or less when attached a metal structure)
<1sec.
Approx. 12 months (500 usages per day)
<0.5mWh
-20℃~50℃ / 0~90%
IP65
95 x 95 x 20 mm
Front Plate
Upper Cover
Battery (CR123A)
20
Light receiving sensor
Lower
Sensitivity setting
Cover
Register / Delete button
Double-sided Tape
CR123A BATTERY
3
Installation Guide
1
If the protective film is not removed from the Front Plate it may
interfere with the function of this product, therefore remove the
protective film from the Front Plate and disassemble the WPS100
cover using a ⊖screwdriver.
※ Insert flat-headed screwdriver
and lift the cover
3
Attach the Lower Cover to where you want to install the sensor
using the Double-sided Tape and/or screws provided.
Double-sided Tape
4
Registering the WPS100 transmitter with the R24 receiver
※ Up to 10 AerWave can be registered with one WR-24 receiver.
Register Button
LED
Connection
point
Delete Button DIP switch for channel setting
Receiver (R24)
※ Make sure to check that all dip switches are in the down (OFF) position before proceeding
1. How to register an WPS100 Transmitter
- Connect power to the WR-24 receiver.
- Press the Register/Delete button on the AerWave switch for 3 seconds whilst simultaneously pressing
The RegisterⅠbutton on the WR-24 receiver.
- The red LED will flash on the WR-24 to indicate registration.
2. How to delete an WPS100 Transmitter
- Connect power to the WR-24 receiver.
- Press the Register / Delete button on the AerWave switch for 3 seconds whilst simultaneously pressing
the DeleteⅡ button on the WR-24 receiver.
- The blue LED will flash on the WR-24 to indicate deletion.
3. How to delete all registered WPS100 transmitters
- Press the RegisterⅠbutton and DeleteⅡbutton on the WR-24 receiver at the same time for 5 seconds.
- The blue LED will flash three times indicating that all registered AerWave transmitters have been deleted.
5
Precautions
1 2
Remove the protective film attached to the front plate Do not install in places exposed to strong sunlight
2
Install batteries and turn the WPS100 ON.
Register the transmitter using the Register/Delete button
(See section 4).
ON/OFF Switch
4
Set the detection distance as required by adjusting the
Sensitivity setting using a screwdriver. Select whether
you want detection to be indicated with an LED or
a Buzzer, then attach the Upper Cover to the sensor.
Connector Automatic door controller
Power (AC/DC12V~24V) Gray ⅹ 2
Yellow ⅹ 2 (Output contact)
White x 2 (Input contact)
In case of using Lock Function
DIP switch
3
4
Avoid moving objects in front of the sensor
Register / Delete button
Do not install in humid areas