Advertisement
ASSEMBLY & INSTALLATION
INSTRUCTIONS
Stanza Cabinet 89050
INTRODUCTION
Thank you for selecting our Porcher product. To ensure that your installation
proceeds smoothly, read these instructions carefully before you begin. Also,
review the recommended tools and materials section. Carefully unpack and
examine your new plumbing fixture.
To maintain the beauty of the finish, avoid placing the furniture in direct sunlight, as sunlight causes fading. Also avoid
extreme changes in temperature by arranging furniture away from radiators, heat and air vents, and air conditioning units.
Avoid placing furniture directly under windows.
ALL INSTALLATION PROCEDURES MUST COMPLY IN STRICT ACCORDANCE WITH APPLICABLE LOCAL
PLUMBING AND BUILDING CODES
Tools and Materials Required
Most of the procedures require the use
of common tools and materials, which
are available from hardware and
plumbing, supply stores. It is essential
that the tools and materials be on hand
before work is begun.
Adjustable Wrench
Basin Wrench
Pipe Wrench
Hacksaw
Regular Screwdriver
Phillips Screwdriver
Drill
Plumbers' Putty or
Caulking
13-3/4"
(349mm)
7-1/2"
(191mm)
Saber Saw
Channel Locks
Putty Knife
Tubing Cutter
10'
Tape
Measure
Level
NOTE: •
Roughing-in Dimensions
41-1/2" (1054mm)
FINISHED WALL
1-1/2"
(38mm)
1-1/4" X 7/8" (32 X 22mm)
LAVATORY ANCHOR
SCREW HOLES (4)
(508mm)
DEPTH WITH DRAWER OPEN 24"
DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND "P" TRAP ARE SUGGESTED.
- 1 -
8"
(203mm)
3-1/4" (83mm)
1-3/4" DIA.
STD. DRAIN
OUTLET
41-1/2"
(1054mm)
3-1/4"
(83mm)
4" (102mm)
SUPPLIES AS
REQUIRED
1-1/4" O.D.
WASTE
1-1/4" O.D.
TAILPIECE
20"
FINISHED
FLOOR
8-1/2"
(216mm)
21-1/4"
(540mm)
2-3/4"
(70mm)
37-1/8"
(943mm)
22"
(559mm)
8 00 0 1 2- 10 0
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Porcher 89050
Summary of Contents for Porcher 89050
- Page 1 INSTRUCTIONS Stanza Cabinet 89050 INTRODUCTION Thank you for selecting our Porcher product. To ensure that your installation proceeds smoothly, read these instructions carefully before you begin. Also, review the recommended tools and materials section. Carefully unpack and examine your new plumbing fixture.
- Page 2 VANITY INSTALLATION C/L of 2 x 6 Suitable reinforcement is required for anchoring the Reinforcement vanity and sink to the wall. Determine horizontal centerline location " " of support from fixture. (see FIGURE 1 Figure 1) Finished Floor If molding is present, either notch the molding to seat the vanity flush against the wall or provide suitable spacer.
- Page 3 INSTALLING THE RIVIERA TOP (20301)… Two people recommended for this installation Install faucet and drain in accordance with manufacturer's instructions. Be certain to apply a bead of sealing putty on the underside of the drain (Part "A") in order to ensure a watertight seal between the sink and drain.
- Page 4 PORCHER FURNITURE LIMITED WARRANTY If inspection of this Porcher plumbing product, within one year after its initial purchase, confirms that it is defective in materials or workmanship, Porcher will repair or, at its option, exchange the product for a similar model. Variations in actual wood color and finishes which may result from natural characteristics of the wood, such as grain patterns, mineral streaks and the like, are not defects and are not covered by this warranty.
Need help?
Do you have a question about the 89050 and is the answer not in the manual?
Questions and answers