Safety Instructions PRECAUTIONS DURING SERVICING recycling as well as small accumulators (rechargeable batteries), mini-batteries (cells) 1. In addition to safety, other parts and and starter batteries should not be thrown into assemblies are specified for conformance with the garbage can. Please leave them at an such regulations as those applying to spurious appropriate depot.
are the necessary instructions to be observed before servicing. isolation transformer should connected in the power line between the receiver and the AC line when a service is performed on the primary of the converter transformer of the set. 2. Comply wi th all caution and safety related provided on the back of the cabinet, inside the cabinet, on the chassis or picture tube.
Page 4
FEATURES - POWER SUPPLY : AC 120V 50/60Hz - FULL FUNCTION REMOTE CONTROLLER - AUTOMATICALLY TURN OFF THE SET WHEN SIGNAL ABSENT LONGER THAN 10 MINUTES - BLUE SCREEN DISPLAY - / V-CHIP - SLEEP - STANDBY - CHANNEL SWAP -POWER CONSUMPTION 80Watt(...
Page 7
NC Editor V 7.0 : Mon Sep 08 10:50:14 2003 - (Untitled) MAIN PCB "PDF " http://www.fineprint.com PDF 文件以 "PDF 制作工厂" 试用版创建 http://www.fineprint.com...
Page 8
PDF 文件以 "PDF 制作工厂" 试用版创建 http://www.fineprint.com...
Page 9
Disassembly In case of trouble, etc., Necessitating disassemble, please disassemble in the order shown in the Exploded View Diagram. Reassemble in the reverse order.
Page 12
M61250AFP/51FP Application Note Revision 2.1 February, 2002 5. Pin Description DC Voltage (V) Pin No. Name Peripheral circuit of pins V RAMP CAP AFT OUT 0.3 ~ 4.7V VIF Vcc 5.0V SIF Vcc 4.6V RAMP OUT V RAMP FEED BACK Mitsubishi Electric...
Page 13
M61250AFP/51FP Application Note Revision 2.1 February, 2002 DC Voltage (V) Pin No. Name Peripheral circuit of pins 3.5V AFC FILTER DEF GND LOGIC GND : 2.0V (FBP Vth L=OFF) FBP IN : 1.0V (FBP Vth L=ON) : 0.0V H OUT : 5.4V DEF Vcc Mitsubishi Electric...
Page 14
M61250AFP/51FP Application Note Revision 2.1 February, 2002 DC Voltage (V) Pin No. Name Peripheral circuit of pins R OUT G OUT B OUT H VCO 3.0V FEEDBACK INTELLIGENT MONITOR : 0.0V INV FBP OUT : 5.0V Mitsubishi Electric...
Page 15
M61250AFP/51FP Application Note Revision 2.1 February, 2002 DC Voltage (V) Pin No. Name Peripheral circuit of pins : 0.0V V PULSE : 5.0V (1)Digital OSD B IN : 0.0V G IN : 3.0V (2)Analog OSD R IN 0.7V 0.0-0.5V: INT RGB FAST BLK 1.5-3.0V: H TONE 4.0-5.0V: EXT RGB...
M61250AFP/51FP Application Note Revision 2.1 February, 2002 DC Voltage (V) Pin No. Name Peripheral circuit of pins : 0.75V : 4.25V 8.7V 8.7V POWER ON : 3.0V CONTROL 150K fsc OUT 1 3.0V 5.7V 5.7V 8.7V H: 5.0V MCU RESET L: 0.0V Y SW OUT 1.7V...
M61250AFP/51FP Application Note Revision 2.1 February, 2002 DC Voltage (V) Pin No. Name Peripheral circuit of pins INTER CARRIER 2.3V AUDIO OUT 2.3V 53.7K 10.5K AUDIO 2.3V BYPASS 53.7K 10.5K EXT AUDIO 2.3V FM DIRECT 3.0V Mitsubishi Electric...
MITSUBISHI MICROCOMPUTERS M37150M8/MF-XXXFP, M37150EFFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER 7. PIN DESCRIPTION Table 7.1 PIN DESCRIPTION Input/ Name Functions Output Power source Apply voltage of 5 V ± 10 % to (typical) V , and 0 V to V This is connected to V ______...
Page 25
MITSUBISHI MICROCOMPUTERS M37150M8/MF-XXXFP, M37150EFFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER Table 7.2 PIN DESCRIPTION (continued) Input/ Name Functions Output Input P5 Input Port P5 is a 2-bit input port. SYNC Horizonta synchronous signal Input The P5 pin is also used as a horizontal synchronous signal input H for OSD.
TDA9302H 3.TDA9302 VERTICAL DEFLECTION OUTPUT CIRCUIT POWER AMPLIFIER FLYBACK GENERATOR THERMAL PROTECTION DESCRIPTION The TDA9302H is a monolithic integrated circuit in HEPTAWATT HEPTAWATT package. It is a high efficiency (Plastic Package) power booster for direct driving of vertical windings of TV yokes. It is intended for use in Color and B & ORDER CODE : TDA9302H W television as well as in monitors and displays.
Page 27
4.TDA16846 TDA 16846 TDA 16847 The TDA 16846 is suited for TV-, VCR- sets and SAT receivers. It also can be good used in PC monitors. The TDA 16847 is identical with TDA 16846 but has an additional power measurement output (pin 8) which can be used for a Temporary High Power Circuit.
Page 28
TDA 16846 TDA 16847 Short Description of the Pin Functions Function A parallel RC-circuit between this pin and ground determines the ringing suppression time and the standby-frequency. A capacitor between this pin and ground and a resistor between this pin and the positive terminal of the primary elcap quantifies the max.
Page 29
5.TDA2614 Philips Semiconductors Product specification 6 W hi-fi audio power amplifier TDA2614 PINNING FUNCTIONAL DESCRIPTION The TDA2614 is a hi-fi power amplifier designed for mains SYMBOL DESCRIPTION fed applications, such as radio and TV. The circuit is n.c. not connected optimally designed for asymmetrical power supplies, but is MUTE mute input...
1 POWER LINE 36003213 WIRE TIE 680*125503-01 680*1255 1 PCS 36003210 WIRE TIE 680*101261-01 680*1012 2 PCS K2008UMZZ-00 K2008UM ASSEMBLY PARTS GENERAL MATERIAL 1 SET 41000249 RADIAL LABEL 569*K1998U-00 569*K199 1 PCS 41001445 RADIAL LABEL 569*275KV10/01 569*275K 1 PCS 41001227...