Page 1
Zigen ZIG-PHASED 18G 1x2 HDMI Repeater and HDMI/ARC Audio Extractor ZIG-PHASED User Manual UM-001-0001-000-01 | March 12, 2021...
Page 2
Please refer to Zigen dealers for the latest details. This warning symbol is used to alert anyone to heed important operating, installing, and maintenance instructions.
Overview 1 Overview The ZIG-PHASED is a simple HDMI 2.0 1x2 Repeater, which takes a single HDMI source and outputs the audio and video to two independent HDMI sinks. The HDMI outputs are featured with independent scaling capabilities and will automatically optimize the video resolutions depending on the capabilities of the connected displays.
Front Panel 2 Front Panel The ZIG-PHASED uses pushbuttons with LEDs to configure the unit’s Video mode, HDR support, Audio Format mode, and Audio Source selection. Repeated pressing of the pushbutton cycles through the modes. Refer to the table printed on the top of the unit to determine the selected modes.
Note: Zigen highly recommends the use of premium 4K certified HDMI cables when viewing UHD 60p 4:4:4 or UHD 60p HDR 4:2:2 video resolutions. Zigen offers these premium 4K certified cables in varying lengths from 3 meters to 9 meters.
Locking and Unlocking the Pushbuttons Once the ZIG-PHASED pushbutton modes have been set, the pushbuttons can be locked to prevent accidental presses and inadvertent changes to the unit’s operation. To lock the pushbuttons, press and hold both VIDEO and AUDIO SRC at the same time until the front panel LEDs change illumination to all off.
HDMI Input will be routed to both HDMI outputs. If ARC is enabled and the ZIG-PHASED is the Audio System, ARC audio sourced from a SmartTV on HDMI Output 1 will be extracted and can be heard on the unit’s Optical and Analog Audio Outputs.
Figure 1: Balanced Audio Phoenix Connector Pinout Power The ZIG-PHASED requires 12VDC @ 1Amp to power the unit. Use the included power adaptor and ensure the locking ring is threaded snugly to prevent inadvertent disconnection of the power jack. Make sure all video, audio, and control ports are properly connected before applying power to the ZIG-PHASED.
The HDMI cable can then be connected in any of the following ways: • Connect the HDMI cables to an Ultra HD display. • Connect the HDMI cables to another Zigen switch or splitter, for cascading purposes. Note: Zigen highly recommends the use of premium 4K certified HDMI cables when viewing UHD 60p 4:4:4 or UHD 60p HDR 4:2:2 video resolutions.
ARC Extraction Mode without an ARC Enabled Audio/Video Receiver at the Input The ZIG-PHASED can extract ARC audio from a Smart TV connected to HDMI Output 1 even if there is no ARC supported AVR or SoundBar in the system (refer to Figure 2).
5 Interconnect Diagram Examples Media Player Video Audio ZIG-PHASED SmartTV AV Receiver Multi-Zone Amplifier Figure 2: ZIG-PHASED 1:2 Repeater. Audio extracted from HDMI In or ARC from SmartTV. Blu-Ray AV Receiver ZIG-PHASED (ARC Support) Video Audio SmartTV 1 Displaying Built-in...
Return Policy If you would like to return a Zigen product, it can be done within 30 days of purchase for a full refund, less shipping and handling. Zigen will not be responsible for shipping and handling of product returns.
1. Updated information for Video Mode Auto (0001). 2. Updated information for Front Panel Lock/Unlock. V00 – December 30, 2020 3. Added HDCP Management (effective ZIG-PHASED Firmware d12.29.20 or newer). 4. Updated the Rear Panel picture. 5. Updated Table 1.