Page 2
Revision Date Version Description 2016/11/18 Version 1.0 Initial Release 2017/01/10 Version 1.1 Specification correction 2019/07/30 Version 1.2 Add Section 1.3 [Note 5] instruction...
Page 3
No part of this manual may be reproduced, copied, translated or transmitted, in whole or in part, in any form or by any means without the prior written permission of the ICOP Technology Inc. Copyright 2019 ICOP Technology Inc. Manual No. IUMPDX3090-01 Ver.1.2A July, 2019 Trademarks Acknowledgment Vortex86DX3...
Table of Contents Table of Contents ..................... iii .General Information ................1 Product Description ............1 Product Specification ............2 Inspection standard for TFT-LCD Panel ......4 Product Dimension ............. 9 Panel Mounting Instruction ..........10 Ordering Information ............12 Packing List ...............
1 .General Information 1.1 Product Description PDX3-090T is an ultra-compact platform for the present demanding embedded and productive applications. It has new Vortex86DX3 SoC CPU which consumes only minimum power requirement when running at 1GHz, and DDR3 memory provides faster data transfer rate. By using 9” TFT LCD, PDX3-090T becomes the perfect choice for a limited budget.
1.3 Inspection standard for TFT-LCD Panel Table 1-2 Inspection Standard DEFECT TYPE LIMIT Note φ<0.15mm Ignore 0.15mm≦φ≦0.5mm N≦4 SPOT Note1 0.5mm<φ 0.03mm<W≦0.1mm, L≦ N≦3 Note1 FIBER VISUAL INTER 1.0mm<W, 1.5mm<L DEFECT φ<0.15mm Ignore POLARIZER 0.15mm≦φ≦0.5mm N≦2 Note1 BUBBLE 0.5mm<φ Mura It’...
Page 9
[Note 1] W : Width[mm], L : Length[mm], N : Number, φ: Average Diameter. White / Black Spot Polarizer Bubble Fig 1-1 Fig 1-2 [Note 2] Bright dot is defined through 6% transmission ND Filter as following. Fig 1-3 PDX3-090T DM&P Vortex86DX3 Panel PC with 9”...
Page 10
[Note 3] C Area: Center of display area O Area: Outer of display area [Note 4] Judge defect dot and adjacent dot as following. Allow below (as A, B, C and D status) adjacent defect dots, including bright and dart adjacent dot. And they will be counted 2 defect dots in total quantity.
Page 11
[Note 5] According to the technical information from LCD manufacturer, the image retention may happen on LCD display if the static image is kept for a period of time without any change. ICOP will suggest customers not to have static image on LCD for over 4 hours without any image movement and also enable screensaver to avoid image sticking issue if LCD displays need to be kept on for a long time.
Page 12
3. After 5 mins, the mura must be disappeared completely. PDX3-090T DM&P Vortex86DX3 Panel PC with 9” WSVGA TFT LCD...
1.5 Panel Mounting Instruction Cut a mounting hole in the panel. (Refer to PDX3-090T Dimensions on page 7) (Note 1) Check and remove the twelve M3 screws in a diagonal pattern as image below if necessary. Place PDX3-090T face-down on a clean, flat surface. Slide the panel cutout around the back of PDX3-090T, until the panel rests directly on the gasket.
Page 15
Note 1: It is strongly recommended that a professional machine shop cut the mounting hole in the panel. Note 2: The length for all twelve M3 screws will be according to the thickness of mounting panel. For example: The length of standard M3 screws for PDX3-090T is 6mm.
1.6 Ordering Information Table 1-3 Ordering Information PART NUMBER DESCRIPTION PDX3-090T-5A 9” Panel PC w/1GB DDR3 / 2USB / Line-Out / LAN / COM / CF / MicroSD / Power Adapter PDX3-090T-8A 9” Panel PC w/1GB DDR3 / 2USB / Line-Out / LAN / COM / CF / MicroSD /...
J8: PS/2 Keyboard 2.3 Connector Pin Assignments J1: CF Master/Slave Switch Pin # Signal Name Pin # Signal Name Pin # Signal Name KBCLK KBDAT Master Slave J3: USB J9: PS/2 Keyboard Pin # Signal Name Pin # Signal Name Pin # Signal Name Pin #...
Page 21
J14: VGA J31: 4-Wires Touch connector Pin # Signal Name Pin # Signal Name Pin # Signal Name R OUT G OUT B OUT HSYNC J32: USB (WLAN Optional) VSYNCD J24: MIC-IN Pin # Signal Name Pin # Signal Name USBD2- Pin # Signal Name...
Power Switch 2.5 External I/O Pin Assignment USB Port Pin # Status Pin # Signal Name Power Connector (5A) USB0- USB0+ Pin # Signal Name GGND GGND PS/2 Keyboard Power Connector (8A) Pin # Signal Name Pin # Signal Name KBCLK +8 ~ 35V PMCLK...
Page 24
J10: COM1 RS232/422/485 (Change setting by BIOS) Pin # Signal Name Pin # Signal Name DCD1/422TX-/RS485- RXD1/422TX+/RS485+ TXD1 / 422RX+ DTR1 / 422RX- DSR1 RTS1 CTS1 RJ45 Pin # Signal Name Pin # Signal Name FTXD+ FTXD- FRXIN+ FRXIN- PDX3-090T DM&P Vortex86DX3 Panel PC with 9”...
2.7 Watchdog Timer There are two watchdog timers in PDX3-090T, we also provide DOS, Linux and WinCE example for your reference. For more technical support, please visit: http://tech.icop.com.tw or download the PDF file: dmp.com.tw/tech PDX3-090T DM&P Vortex86DX3 Panel PC with 9” WSVGA TFT LCD...
3 .Driver Installation The Vortex86DX3 processor is integrated RDC Display chip which is an ultra low powered graphics chipset with total power consumption at around 1-1.5 W. The Vortex86DX3 processor is integrated 10/100Mbps Ethernet controller that supports both 10/100BASE-T and allows direct connection to your 10/100Mbps Ethernet based Local Area Network for full interaction with local servers, wide area networks such as the Internet.
Operating system support The PDX3-090T provides the VGA and LAN drivers for Linux, Windows CE, Windows XP Professional, Windows 7, and Windows Embedded standard (WES2009 / WES7). Please get the drivers from ICOP official website: tech.icop.com.tw PDX3-090T also supports most of the popular Linux distributions, for more detail information, please visit DMP official website: dmp.com.tw/tech/ 3.1 PDX3-090T Development Note...
Page 31
<Linux installation note> Please forced the IDE setting in BIOS to PIO mode before install Linux on PDX3-090T as follows: Go to the advanced BIOS setting and make the “Onboard IDE Operate Mode” is “Legacy Mode” < Windows XP and Windows 7 installation note > Please visit technical website to get more information: tech.icop.com.tw PDX3-090T DM&P Vortex86DX3 Panel PC with 9”...
3.2 BIOS Default setting If the system cannot be booted after BIOS changes are made, Please follow below procedures in order to restore the CMOS as default setting. Press < End > Key, when the power on Press < Del > to enter the AMI BIOS setup Press <...
Need help?
Do you have a question about the PDX3-090T-5A and is the answer not in the manual?
Questions and answers