Summary of Contents for Rato RBSL40
- Page 1 RATO LITHIUM-ION CORDLESS BLOWER RBSL40 Owner’s Manual Read all safety rules and instructions carefully before operating this tool...
-
Page 2: Table Of Contents
Original instructions CONTENTS Contents…………………………………………………………………………………………………….……………….…………….…….………..….……..2 Symbols……………………………………………………………………………………………………….………………….…..…………..……….…………3 Know your 40V cordless blower…………………………………………………………………….….…………….………………..………..……….4 Technical data…………………………………………………………………………………………………………….…………………….…………….…..5 Original instruction………………………………………………………………………………………..…………….……………………………...………6 Assembly……………………………………………………………………………………………………………………….……………………..…..…………12 Operation……………………………………………………………………………………………………………….………….…………….……….…...…..14 Transporting and storing………………………………………………………………..………………………………….…………….………..………..15 Maintenance and repairs …………………………………..………………………………………………………………….……..………….….….….16 Troubleshooting……………………………………………………………………………………………..…………………………..………………...……16 EC- Declaration of Conformity………………………………………………………………………………………………………….…….…….……..17 2-English... -
Page 3: Symbols
Original instructions SYMBOLS • Dispose of properly. Read instruction handbook Wear eye protection Wear ear protection Do not use in the rain or leave outdoors while it is raining Keep bystanders away The distance between the machine and bystanders shall be least 5m Switch off and remove battery before adjusting and cleaning. -
Page 4: Know Your 40V Cordless Blower
Original instructions KNOW YOUR 40V CORDLESS BLOWER TURBO BUTTON CONTROL HANDLE SPEED LOCK LEVER TRIGGER SWITCH BLOWER TUBE RELEASE BUTTON BATTERY PACK Fig.1 KNOW YOUR 40V CORDLESS BLOWER (See Fig.1) The safe use of this product requires an understanding of the information on the product and in this operator’s manual as well as a knowledge of the project you are attempting. -
Page 5: Technical Data
Original instructions TECHNICAL DATA Type RBSL40 Voltage 40V Max* Lithium ion No load speed 21000rpm Blow speed 53m/s Air capacity 12.7m³/min Machine weight 2.3KG (without battery) *Voltage measured without workload. Initial battery voltage reaches maximum of 40 volts. Nominal voltage is 36 volts. -
Page 6: Original Instruction
The RATO RBAT40 charger recharges the RATO RBEI40 battery. WARNING Batteries and chargers not explicitly approved for the blower by RATO may cause a fire or explosion. This can result in serious or fatal injuries and damage to property. •Use the blower with a RATO RBEI40 battery. - Page 7 Original instructions ORIGINAL INSTRUCTION •Wear work gloves made of durable material. •Wearing unsuitable footwear may cause you to slip or stumble. This can result in personal injury. •Wear sturdy footwear with non-slip soles. Work Area and Surroundings WARNING Bystanders, children and animals are not aware of the dangers of the blower or flying debris. Innocent bystanders, children and animals may be seriously injured and damage to property may occur.
- Page 8 •Never modify your blower. Exception: Mounting a nozzle approved for this blower model. •If the controls do not function properly: Do not work with the blower. •Only fit original RATO accessories designed for this blower model. •Mount accessories as described in this instruction manual or the instruction manual supplied with the accessory.
- Page 9 Original instructions ORIGINAL INSTRUCTION -Charger is clean and dry. WARNING •If the product does not comply with safety requirements, components will no longer function properly or safety devices may be rendered inoperative. This can result in serious or fatal injuries. •Do not use a damaged charger.
- Page 10 Original instructions ORIGINAL INSTRUCTION of the charger. •During charging, a damaged or defective charger may give off an unusual smell or smoke. This can result in injuries and damage to property. •Disconnect the mains plug from the mains power supply. •Insufficient heat dissipation may cause the charger to overheat and a fire to break out.
- Page 11 This can result in serious or fatal injuries. Do not attempt to service or repair the blower, battery or charger. If the blower, battery or the charger require servicing or repairs: Contact your RATO servicing dealer. English...
-
Page 12: Assembly
Original instructions ASSEMBLING ASSEMBLING THE BLOWER TUBE (See Fig. 2-3) ALWAYS REMOVE THE BATTERY PACK BEFORE ASSEMBLING THE BLOWER TUBE Fig.2 Fig.3 Fit the Blower Tube to the motor housing as shown in Fig. 2. Check the Blower Tube is firmly secured. Note: Before disassembling the Blower Tube, be sure the variable speed trigger is on off position. - Page 13 Original instructions ASSEMBLING ASSEMBLING THE BATTERY CARTRIDGE SCREW SCREW Fig.6 Fig.7 1.Place battery cartridge on to the applicable position of housing (Fig.4,Fig.5) 2.Tighten four screws so that the cartridge assembly cannot move.(Fig.6,Fig.7) English...
-
Page 14: Operation
Original instructions OPERATION TO REMOVE OR INSTA LL BATT ERY PACK (Fig.8) Fig.8 Depress the Battery Release Button to release battery pack from your tool. After recharging, insert the battery pack into tool’s battery port. A simple push and slight pressure will be sufficient.(Fig.8) Switching the Blower On/Off(Fig.9) Fig.9 OPERATION... -
Page 15: Transporting And Storing
Original instructions TRANSPORTING AND STORING Transporting the Blower Switch off the blower and remove the battery. carry the blower by the control handle. Transporting the blower in a vehicle: Secure the blower to prevent it turning over or shifting. Transporting the Battery Switch off the blower and remove the battery. -
Page 16: Maintenance And Repairs
•The blower cannot be serviced or repaired by the user. – If your blower has a malfunction or is damaged or requires servicing: Contact your RATO servicing dealer. •Servicing and Repairing the Battery. The battery requires no servicing and cannot be repaired. -
Page 17: Ec- Declaration Of Conformity
Original instructions EC- Declaration of Conformity Here with we, Zhejiang Zhongjian Technology Co., Ltd. No.10 Mingyuan South AVE, Economic Development Zone, Yongkang, Zhejiang 321300, China declare that the following Appliance complies with the appropriate basic safety and health requirements of the EC Directives based on its design and type, as brought into circulation by us This declaration relates exclusively to the machinery in the state in which it was placed on the market, and excludes components which are added and/or operations carried out subsequently by the final user.