Page 2
SERVICE MANUAL AKAI 21CTU94BC This manual is the latest at the time of printing, and does not include the modification which may be made after the printing, by the constant improvement of product...
SAFETY PRECAUTIONS The design of this product contains special hardware, many 10. Isolation Check circuits and components specially for safety purposes. For (Safety for Electrical Shock Hazard) continued protection, no changes should be made to the After re-assembling the product, always perform an isolation original design unless authorized in writing by the check on the exposed metal parts of the cabinet (antenna manufacturer.
TV Block diagram TDA11105-XXXX video IF IN R IN TUNER RF AGC B IN video video CHROMA AR i1 4052 VIDEO CVBS/Y IN ALi 1 Video IN CVBS1 IN 24C08 CVBS2 IN ARi 2 MA IN L ALi 2 MAOUTR MA IN R MAOUTL RGB OUT...
REPLACEMENT OF MEMORY IC 1. MEMORY IC. This TV uses memory IC. In the memory IC are memorized data for correctly operating the video and deflection circuits. When replacing memory IC, be sure to use IC written with the initial value of data. 2.
Page 12
production doesn't need to carry on M 3~ adjustments of M9. In "M0"~under"M9" appearance press” CALL” the key can get into "M" appearance. At “M”under the appearance press “-/-“ the key can get into “BUS OPEN” appearance, at “BUS OPEN under, press “-/-“...
Page 13
C standard UOC for export bus control adjustment item default setting 2007-12-05 Items Variable Preset recommendation 50HZ 60HZ 50HZ 60HZ V. LOPE +/-32 Picture vertical center adjustment V. SIZE +/-32 Vertical amplitude adjustment V. SC +/-32 Vertical S Correction Adjustment V.LINE +/-32 Vertical positions adjustment...
Page 14
0~63 Cut-off control range 0:normal control range 1:extended control range CHINESE ON/OFF OSD language selection THAI ON/OFF OSD language selection VIETNAM ON/OFF OSD language selection INDONESIA ON/OFF OSD language selection ARABIC ON/OFF OSD language selection Vercital amplitude System I output signal amplitude correction 0:no correction 1:amplitude + 12% Control sequence of beam current limiting 0:normal operation(contrast—brightness)
Page 15
DCXO Crystal load electric capacity compensate Forced slicing level for vertical sync Slicing level for horizontal sync separator 0:50% 1:30%,direction top sync Group delay on CVBSI signal 0:no group delay correction 1: group delay correction switched on Sync hronization of OSD/TEXT display ON/OFF Black current stabilization Disable flash protection from deflection timer...
Page 16
DSGLS Extra gain selection loudspeaker outputs 0:+0 Db 1:+6 Db No red reduction during blue stretch AMLOW Audio output signal for AM sound GSSIF Extra gain-range SSIF for AM demodulation V.P1 0~100 V.P1 volume of VALUE V.P25 0~100 V.P25 volume of VALUE V.P50 0~100 V.P50 volume of VALUE...
Page 17
M.COLOR 0~100 mild Color in pp mode M.SHARP 0~100 mildSharpness in pp mode W.BRT 0~100 factory adjusts Brightness W.CONT 0~100 factory adjusts Contrast W.COLOR 0~100 factory adjusts Color SC BRT 0~100 Subsidiary Bright Adjustment COOL 0~63 Cool color adjustment WARM 0~63 Warm color adjustment ON/OFF...
Page 18
4 , LOGO EDIT This software LOGO is a pair of pleased words and customer to edit 2 kinds, at the M_MODE, long press[P.P]the key can get into a pair of pleased words editor appearance. ( Operate Press[1]/[2] keys: The LOGO perpendicular position adjust, [1] adjusts upward, [2] get down adjustment;...
ICs functional description UOC TDA11105-XXXX/TDA11106-XXXX SYMBOL DESCRIPTION IF VO IF video output / selected CVBS output Supply voltage TV processor(+5v) VCC AUDIO 8 volt supply for audio switches(+5V~8V) PLL IF IF-PLL loop filter GND2 Gaound 2 for TV processor DECSDEM decoupling sound demodulator or SIF input 2 FMDEMOUT audio output /AM audio output (volume controlled)
Page 20
VDDC Supply(3.3V) GND5 Ground 5 OPT programming Voltage VDDA Supply voltage(3.3V) BOUT Blue output GOUT Green output ROUT Red output BLKIN black current input / V-guard input BCL IN beam current limiter input B input / U (B-Y) input / P input Y3/CVBS3 G input / Y input...
Page 21
BLOCK AND APPLICATION DIAGRAM TDA7266SA V CC 470µF 100nF 0.22µF OUT1+ S-GND OUT1- Vref 0.22µF OUT2+ OUT2- PW-GND D94AU175B ABSOLUTE MAXIMUM RATINGS y l l Total Power Dissipation (T ° 0 ° ° stg, THERMAL DATA ° th j-case ° th j-amb ELECTRICAL CHARACTERISTCS = 11V, R...
Page 22
Ω Mute Threshold for V > 6.4V; Vo = -30dB MUTE for V < 6.4V; Vo = -30dB -075 -0.5 ST-BY µA ST-BY Total Output Voltage A Curve; f = 20Hzto 20KHz µV Distortion vs Frequenc Gain vs Frequency Le vel(dB r) THD(%) 5.0000 4.0000...
LA9302A/8177/LA78041/LA78040 Function : vertical output Symbol Function Symbol Function INV IN Input V OUT Vertical output VCC1 Power VCC2 Output power supply PUMP UP Pump up power NON INV IN Negative feedback Test point Waveforms 1.2Vpp 2.6Vpp 3.8Vpp 2.5Vpp 2.5Vpp TDA11105 PIN45 TDA11105 PIN44 TDA11105 PIN46...
PURITY / CONVERGENCE ADJUSTMENT PURITY ADJUSTMENT WEDGE Demagnetize CRT with the demagnetizer. DEFLECTION YOKE Loosen the retainer screw of the deflection yoke. Remove the wedges. Input a green raster signal from the signal generator, and turn the screen to green raster. Move the deflection yoke backward.
Page 25
STATIC CONVERGENCE ADJUSTMENT 1. Input a crosshatch signal. 2. Using 4-pole convergence magnets, overlap the red and blue lines in the center of the screen (Fig. 1) and turn them to magenta (red/blue). (FRONT VIEW) 3. Using 6-pole convergence magnets, overlap the magenta (red/blue) and green lines in the center of the screen and turn them to white.