1. Manuals
  2. Brands
  3. Ningbo Manuals
  4. Transducer
  5. KPT-G1210
  6. Manual

Ningbo KPT-G1210 Manual

Hide thumbs

Advertisement

Table of Contents

SPECIFICATION
Customer :
Applied To :
Product Name : Piezo Transducer
Model Name : KPT-G1210( 有字 )
Drawing No. : KP3.840.201.01R
Compliance with RoHs( 本品符合 ROHS 指令 )
Signature of Approval
Signature of KEPO
Approved by
宁波凯普电子有限公司
Ningbo Kepo Electronics Co.,Ltd.
Checked by
受
Issued by
控
Date

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the KPT-G1210 and is the answer not in the manual?

Questions and answers

Related Manuals for Ningbo KPT-G1210

Summary of Contents for Ningbo KPT-G1210

  • Page 1 SPECIFICATION Customer : 受 控 Applied To : Product Name : Piezo Transducer Model Name : KPT-G1210( 有字 ) Drawing No. : KP3.840.201.01R Compliance with RoHs( 本品符合 ROHS 指令 ) Signature of Approval Signature of KEPO Approved by Checked by...

  • Page 2: Table Of Contents

    3. Maximum Rating 额定极限条件 4. Electrical Characteristics 电性能 5. Measuring Method 测试方法 6. Physical Characteristics 机械性能 7. Environmental Characteristics 环境性能 8. Dimensions 尺寸 9. Packaging Standard 包装标准 10. Cautions 警告 11. Cautions for Use 注意事项 12. Revision 履历表 Ningbo Kepo Electronics Co.,Ltd.

  • Page 3: Maximum Rating

    PC/Black 壳体材质 / 颜色 : PC/ 黑 3. 额定极限条件 Maximum Rating 项目 规 格 Item Specification 输入电压 30Vp-p input Voltage 工作温度范围 -20 ～ +80 ℃ Operating Temperature Range 储存温度范围 -30 ～ +100 ℃ Storage Temperature Range Ningbo Kepo Electronics Co.,Ltd.

  • Page 4: Electrical Characteristics

    ℃ , 湿度 45 ～ 85%R.H. 的范围内测试 . Part shall be measured under a condition (Temperature :+5 to +35 ℃ ,Humidity :45 to 85%R.H.)unless the standard condition (Temperature :+25 ± 3 ℃ ,Humidity :60 ± 10 %R.H.) is regulated measure. Ningbo Kepo Electronics Co.,Ltd.

  • Page 5: Physical Characteristics

    (Except the edge of terminal) 分别在每个插针的轴向施加 9.8 牛顿的静荷 插针没有断开和 重 10 秒 . 可见的损伤 插针强度 No visible Terminal The force 10 seconds of 9.8N is applied to damage and Strength Pulling each terminal in axial direction. cutting off Ningbo Kepo Electronics Co.,Ltd.

  • Page 6: Environmental Characteristics

    After 5 above cycles, sounder shall be measured after being placed in natural condition for 4 hours. 表 1 Table 1 项 目 试验后变化量 Specification after test Item 声压级 初始值± 10dB Sound Pressure Level Initial Value ± 10dB Ningbo Kepo Electronics Co.,Ltd.
  • Page 7 Page Specification for Transducer Revision No. Model No. : KPT-G1210(有字) Drawing No. KP3.840.201.01R 7. Dimensions KEPO FIRST ANGLE PROJECTION Unit ± 0.5 Tolerance : Ningbo Kepo Electronics Co.,Ltd.
  • Page 8 控制在 3 秒内 . In case of using solder iron for soldering, the top of soldering iron's temperature should be kept less than +350 ℃ .Moreover the soldering time should be also kept with in 3seconds. Ningbo Kepo Electronics Co.,Ltd.
  • Page 9 Page Specification for Transducer Revision No. Model No. : KPT-G1210(有字) Drawing No. KP3.840.201.01R 9. Revision Rev. DATE PAGE DESCRIPTION SIGN primary 2009.05.13 Ningbo Kepo Electronics Co.,Ltd.

Table of Contents