Advertisement
Quick Links
These instructions contain operating information and should be left with the unit.
Electro Boiler
Units
Alpha-Numeric Display Module
Operation Manual
Edition 3.1
(For use with Software version 7.4 & subsequent issues)
Installation in countries covered by EC Directives:
This product will meet the requirements of the Low Voltage Safety Directive 73 / 23 EEC and the
EMC Directive 89 / 336 EEC when installed in accordance with the instructions contained in this
manual. Failure to comply with these instructions may invalidate the manufacturer's warranty or
any certificate/declaration of conformance requested to be supplied with the unit.
Advertisement
Summary of Contents for Vapac VapaNet
- Page 1 These instructions contain operating information and should be left with the unit. Electro Boiler Units Alpha-Numeric Display Module Operation Manual Edition 3.1 (For use with Software version 7.4 & subsequent issues) Installation in countries covered by EC Directives: This product will meet the requirements of the Low Voltage Safety Directive 73 / 23 EEC and the EMC Directive 89 / 336 EEC when installed in accordance with the instructions contained in this manual.
-
Page 2: Table Of Contents
Contents Introduction Alpha-Numeric Display Non Password Protected Menu Options User Level Password “4602” Service Engineer Level Password “5699” 12... -
Page 3: Introduction
(NB pressing the down arrow in the If you report a fault to Vapac Humidity Control example above will take you to the “Status” line Ltd, you may be asked to provide this &... -
Page 4: Non Password Protected Menu Options
PCB is changed, or if the display is “field fitted”. Factory Setup This option should only be used by Engineers from Vapac Humidity Control Ltd. It is password protected and used to set the number of electrodes and number of times the electrode cable passes through the toroid... - Page 5 “master unit has two cylinders). Slave Vapac 1 (if fitted) Used to select the first slave Vapac (this will only be displayed if there is a slave unit on the system) in which case 3-2-1 will again be “unit” properties and 3-2-2 “cylinder 1 “...
- Page 6 “master unit has two cylinders). Slave Vapac 1 (if fitted) Used to select the first slave Vapac (this will only be displayed if there is a slave unit on the system) in which case 3-2-1 will again be “unit” properties and 3-2-2 “cylinder 1 “...
- Page 7 Displays the total number of cylinders attached to the system or network 4-1-1-13 VOS Algorithm Displays the selected algorithm which is used by Vapac Operating System either “VOS 4” or “VOS 6” the standard setting is “VOS 6” 4-1-1-14 Water Economy Displays whether water economy is “enabled”...
-
Page 8: User Level Password "4602
PCB is changed, or if the display is “field fitted”. This option should only be used by Engineers from Vapac Humidity Control Factory Setup Ltd. - Page 9 “master unit has two cylinders). Slave Vapac 1 (if fitted) Used to select the first slave Vapac (this will only be displayed if there is a slave unit on the system) in which case 3-2-1 will again be “unit” properties and 3-2-2 “cylinder 1 “...
- Page 10 “master unit has two cylinders). Slave Vapac 1 (if fitted) Used to select the first slave Vapac (this will only be displayed if there is a slave unit on the system) in which case 3-2-1 will again be “unit” properties and 3-2-2 “cylinder 1 “...
- Page 11 Displays the total number of cylinders attached to the system or network 4-1-1-13 VOS Algorithm Displays the selected algorithm which is used by Vapac Operating System either “VOS 4” or “VOS 6” the standard setting is “VOS 6” 4-1-1-14 Water Economy Displays whether water economy is “enabled”...
-
Page 12: Service Engineer Level Password "5699
PCB is changed, or if the display is “field fitted”. Factory Setup This option should only be used by Engineers from Vapac Humidity Control Ltd. It is password protected and used to set the number of electrodes and number of times the electrode cable passes through the toroid... - Page 13 “master unit has two cylinders). Slave Vapac 1 (if fitted) Used to select the first slave Vapac (this will only be displayed if there is a slave unit on the system) in which case 3-2-1 will again be “unit” properties and 3-2-2 “cylinder 1 “...
- Page 14 “master unit has two cylinders). Slave Vapac 1 (if fitted) Used to select the first slave Vapac (this will only be displayed if there is a slave unit on the system) in which case 3-2-1 will again be “unit” properties and 3-2-2 “cylinder 1 “...
- Page 15 Displays the total number of cylinders attached to the system or network 4-1-1-13 VOS Algorithm Displays the selected algorithm which is used by Vapac Operating System either “VOS 4” or “VOS 6” the standard setting is “VOS 6” 4-1-1-14 Water Economy Displays whether water economy is “enabled”...
- Page 16 Info “Sensing Head” is used as the control signal, as the only adjustments available at this level are associated with “Sensing Head” control. Adjust Master Vapac Selects the master vapac adjust parameters 5-1-1 Unit Selects the “unit” parameters. 5-1-1-1 Set point Selects the “set point”, use the up/down keys to adjust the controller set...
- Page 17 The above service options are repeated for slave units 1 to 9 (if applicable) LE 7.4 Service Engineering Master Vapac Selects the master vapac adjust parameters 7-1-1 Unit Selects the “unit” parameters. 7-1-1-1 Fault Output Allows the “fault” alarm signal to be set to either “Continuous” or “Pulsed.
- Page 18 Made in England by: Vapac Humidity Control Ltd. Printed in Great Britain. April 2007. Vapac Humidity Control Ltd reserve the right to change the design or specification Of the equipment described in this manual without prior notice...