GOM-804 & GOM-805 使用手册 前面板介绍 Arrow keys, LCD display Function key ESC key Enter keys G O M -8 0 5 DC Milliohm Meter Compare Binning terminal TCONV TEMP Enter Speed GUARD Trigger Scan GUARD terminal Display Local Diode Drive...
GOM-804 & GOM-805 使用手册 TFT-LCD 介绍 Function mode Range Trigger mode Rate Remote mode Average value Dry circuit Remote error Drive signal Memory REL value number Function control Main indicators measurement display Function mode settings Secondary menus 启 用 功 能 显 示...
GOM-804 & GOM-805 使用手册 后面板介绍 GPIB port RS232 port Handler/ Scan/ Ext I/ O GPIB RS232 HANDLER / SCAN / EXT I/O 240V , 50 60Hz 25VA MAX TC SENSOR WARNING USB B TO AVOID SHOCK, REMOVE INPUTS BEFORE OPENING.
Ohm range GOM-804 & GOM-805 使用手册 选 择 电 阻档 位 背 景 正常电阻测量和温度补偿功能会使用到该功能。 Ohm measurement 手 动 按 Range 键,使用上下键手动选择电阻档位 Set range Range select indicator 自 动 换 档 长按 Range 键开启自动换档 Range, Auto range 档 位 列 表...
GOM-804 & GOM-805 使用手册 比较功能 背 景 比较测量值和“参考”值,带上(HI)和下(LO)限制。如 果测量值在上限和下限之间, 那么测量值判定为 IN。 三种比较模式: ABS、△% 和 % 模式。 ABS 模式显示测量值与参考值(△)的绝对差, 并将测 量值与上限(HI)和下限(LO)进行比较。 上下限为电阻 绝对值。 Compare function Measured value indicator Absolute difference of measured value from Reference value Pass/ Fail judgment Reference, limits, compare mode and beep mode 如果测量值在上限和下限之间,则判定测量值为...
Page 41
GOM-804 & GOM-805 使用手册 Compare function Measured value indicator Deviation of the measured value from the reference value as a percentage Pass/ Fail judgment Reference, limits, compare mode and beep mode 上限(HI)和下限(LO)设成百分比(与%比较模式一 致)。 如果测量值在上限和下限之间,则判定测量值为 IN(pass);如果小于下限值,则判定为 LO;如果高 于上限值,则判定为 HI。 Lower Reference...
Page 42
GOM-804 & GOM-805 使用手册 Compare function Measured value indicator Measured value as a percentage of the reference value Pass/ Fail judgment Reference, limits, compare mode and beep mode 如果测量值在上限和下限之间,则判定测量值为 IN(pass);如果小于下限值,则判定为 LO;如果高 于上限值,则判定为 HI。 Lower Reference Upper limit value limit 所有比较模式,屏幕都将显示每次判断的 IN、HI 或...
Page 43
GOM-804 & GOM-805 使用手册 Move and edit Select and Enter confirm Reference 范 围 : 000.0001~ 999.9999 (mΩ/Ω/kΩ/MΩ) △、%或△%值将根据新的参考 参考值设置完成后, 注 意 值相应改变 4. 上 &下 限 设 置 使用方向键浏览上限或下限设置,按 Enter 使用左右方向键选择数位。使用上下方向键编辑数 值。按 Enter 确认设置 重复操作,设置其它限制(上限或下限) Move and edit Select and...
Page 48
GOM-804 & GOM-805 使用手册 Count 显示模式以列表形式将结果显示在屏幕右侧, bin 设置显示在左侧。 Tabulated result of each bin Overall results Clear results Upper and lower limits of Bin 1~8 进入 Disp 设置,按 Enter 选择显示模式 Move Toggle Enter Disp setting 8. 如 何 清 除 Count 显示模式下,按...
Page 64
GOM-804 & GOM-805 使用手册 电 源 频 率 背 景 选择适当的电源滤波器, 减少 AC 电源频率对毫欧姆 测量值的影响。默认为 AUTO。 1. 选 择 电 源 频 率 在任一主屏幕,按 键 Meas. Setup menu icon 设 置 进入 Meas. Setup,按 Enter 进入 Line Frequency,按 Enter Move...
Page 65
GOM-804 & GOM-805 使用手册 PWM 设 置 背 景 设置 PWM Drive 的占空比,可设成 ON time 和 OFF time。 OFF time time Drive 设置详情见30页 1. 选 择 PWM 设 在任一主屏幕,按 键 Meas. Setup menu icon 置 进入 Meas. Setup,按 Enter 进入 PWM,按 Enter...
Page 66
GOM-804 & GOM-805 使用手册 系统设置 背 景 查看系统信息、设置开机状态、远程接口、屏幕亮 度、外部接口、蜂鸣设置以及进入校准菜单。 系 统 信 息 背 景 系统信息显示厂商、型号、软件版本、序列号。与 *idn?指令(见147页)返回值一致。 1. 查 看 系 统 信 息 在任一主屏幕,按 键 System menu icon 进入 System,按 Enter 系统信息显示在屏幕上方 Move Select menu Enter or setting System Information 按...
Page 67
GOM-804 & GOM-805 使用手册 开 机 状 态设 置 背 景 可调取之前的设置或默认设置。 1. 选 择 开 机 状 态 在任一主屏幕,按 键 System menu icon 设 置 进入 System,按 Enter 进入 Power On Status Setup,按 Enter Move Select menu Enter or setting 2.
GOM-804 & GOM-805 使用手册 扫 描 输 出 背 景 不同情况下的扫描输出时序图如下: Ready message displayed… After the manual trigger key is pressed…. Relay Relay Pass Pass High High Clock Clock STRB STRB Scan channel 1. Delay time has Scan channel n. Delay time has elapsed.
后面板的 Type B USB 接口用于远程控制。当与 PC 连接时,该接口作为一个虚拟 COM 口。 USB 接口需要安装 USB 驱动。详情见89页 注 意 1. 连 接 和 设 置 设置 USB 接口,在 见68页 System>Utility>Interface menu Type A-B USB 线一端连接到 GOM-804/805 后面板的 USB B 接口 另一端连接到 PC 机的 Type A 接口...
设置 USB 接口,在 Page 68 System>Utility>Interface menu Type A-B USB 线一端连接到 GOM-804/805 后面板的 USB B 接口。 另 一端连接到 PC 机的 Type A 接口 进入 Windows Device Manager 如 Windows 7 进入: Start Menu > Control Panel > Hardware and Sound >...
GOM-804 & GOM-805 使用手册 BINNing 指令 Binning commands are only applicable to GOM-805. BINNing:COUNt:CLEar Query Description Clear all bin sorting function test result counts. Syntax BINNing:COUNt:CLEar Parameter/ <None> BINNing:COUNt:TOTal Query Description Returns the total number (count total) of test bin results.
GOM-804 & GOM-805 使用手册 Query Syntax BINNing<X>:COUNt:RESult? Parameter <X> Return parameter <NR1> 0~99999999 Example BINN1:COUN:RES? >100 Indicates that bin1 has a pass count of 100. BINNing<X>:LIMit:LOWer Query Description Sets or returns the lower limit value (absolute value) for the selected bin.
GOM-804 & GOM-805 使用手册 <String> mohm/ohm/kohm/maohm,unit If the unit is not set, the unit will be automatically set by the present range. Return parameter <NR3> 000.0000~999.9999E± X Example BINN1:LIM:UPP 0.95,maohm Sets bin1 upper limit value to 0.95MΩ. BINN1:LIM:UPP? >0.9500E+6 Returns the upper limt as 0.95MΩ.
GOM-804 & GOM-805 使用手册 Example BINN1:PERC:UPP 150.95 Sets the bin1 upper limit percent value to +150.95%. BINN1:PERC:UPP? >150.95 Returns the upper limit percentage value as +150.95%. BINNing:LIMit:BEEPer Query Description Sets or returns beeper mode for the bin sorting function. Syntax...
GOM-804 & GOM-805 使用手册 Parameter/ The test results are judged from Return parameter absolute values. DPER The test results are judged from a reference value ± a percentage offset. (delta percent) Example BINN:LIM:MODE DPER Sets the mode to Δ%. BINNing:LIMit:REFerence...
GOM-804 & GOM-805 使用手册 比较指令 CALCulate:COMPare:TYPE Query Description Sets or returns the compared function. Syntax CALCulate:COMPare:TYPE {OHM|TC} Query Syntax CALCulate:COMPare:TYPE? Parameter/ OHM function. Return parameter TC function. Example CALC:COMP:TYPE TC Sets the compare to TC function. CALCulate:COMPare:LIMit:REFerence Query Description Sets or returns the limit reference value for the compare function.
GOM-804 & GOM-805 使用手册 CALCulate:COMPare:LIMit:MODE Query Description Sets or returns the compare mode for the compare function. Syntax CALCulate:COMPare:LIMit:MODE {ABS|DPER|PER} Query Syntax CALCulate:COMPare:LIMit:MODE? Parameter/ The test results are judged from absolute Return parameter values. DPER The test results are judged from a reference value ±...
GOM-804 & GOM-805 使用手册 CALCulate:COMPare:LIMit:UPPer Query Description Sets or returns the upper limit value for the compare function. Syntax CALCulate:COMPare:LIMit:UPPer {<NRf>[,<String>]} Query Syntax CALCulate:COMPare:LIMit:UPPer? Parameter <NRf> 000.0000~999.9999 <String> mohm/ohm/kohm/maohm,unit If unit is not set, the unit will be automatically set by the present range.
GOM-804 & GOM-805 使用手册 CALCulate:COMPare:PERCent:UPPer Query Description Sets or returns the upper limit percent value for the compare function. Syntax CALCulate:COMPare:PERCent:UPPer <NRf> Query Syntax CALCulate:COMPare:PERCent:UPPer? Parameter <NRf> 000.00~999.99 Return parameter <NR2> 000.00~999.99 Example CALC:COMP:PERC:UPP 90.00 Sets the upper limit percent value to +90.00%.
GOM-804 & GOM-805 使用手册 Example CALC:COMP:MATH:DAT? >+0.3658E+2 Returns the deviation as 36.58%. CALCulate:COMPare:LIMit:RESult Query Description Returns the compare function test result. Query Syntax CALCulate:COMPare:LIMit:RESult? Return parameter <NR1> 0: LO 1: IN 2: HI Example CALC:COMP:LIM:RES? >2 Indicates that the test result is HI.
GOM-804 & GOM-805 使用手册 计算指令 CALCulate:COMPare:BEEPer€ Query Description Sets or returns the compare function beeper mode. Syntax CALCulate:COMPare:BEEPer {OFF|PASS|FAIL} Query Syntax CALCulate:COMPare:BEEPer? Parameter/ Turns the beeper off. Return parameter PASS The beeper will sound on a pass test result. FAIL The beeper will sound on a fail test result.
GOM-804 & GOM-805 使用手册 Parameter <NRf> 000.0000~999.9999 <String> mohm/ohm/kohm/maohm,unit If the unit is not set, the unit will be automatically set by the present range. Return parameter <NR3> 000.0000~999.9999E± X Example CALC:COMP:LIM:LOW 0.123,maohm Sets the lower limit value to 0.123MΩ.
GOM-804 & GOM-805 使用手册 <String> mohm/ohm/kohm/maohm,unit If unit is not set, the unit will be automatically set by the present range. Return parameter <NR3> 000.0001~999.9999E± X Example CALC:COMP:LIM:REF 10.00,mohm Sets the limit reference value to 10.00mΩ. CALC:COMP:LIM:REF? >10.0000E-3 Returns the limit as 10.00mΩ.
GOM-804 & GOM-805 使用手册 CALCulate:COMPare:MATH:DATa Query Description Returns the deviation value for the compare function. Query Syntax CALCulate:COMPare:MATH:DATa? Return parameter <NR3> ± 0.0000~9.9999E± X. Example CALC:COMP:MATH:DAT? >+0.3658E+2 Returns the deviation as 36.58%. CALCulate:COMPare:PERCent:LOWer Query Description Sets or returns the lower limit percent value for the compare function.
GOM-804 & GOM-805 使用手册 CALCulate:SCAN:CHANnel Query Description Sets or returns the channel for the scan function. Syntax CALCulate:SCAN:CHANnel <NR1> Query Syntax CALCulate:SCAN:CHANnel? Parameter/ <NR1> 1~100 Return parameter Example CALC:SCAN:CHAN 5 Sets the channel to 5. CALCulate:SCAN:DELay Query Description Sets or returns the interval delay for the scan function.
GOM-804 & GOM-805 使用手册 CALCulate:SCAN:LIMit:MODE Query Description Sets or returns the scan function compare mode. Syntax CALCulate:SCAN:LIMit:MODE {ABS|DPER} Query Syntax CALCulate:SCAN:LIMit:MODE? Parameter/ The test results are judged from Return parameter absolute values. DPER The test results are judged from a reference value ±...
GOM-804 & GOM-805 使用手册 <String> mohm/ohm/kohm/maohm,unit If unit is not set, the unit will be automatically set by the present range. Return parameter <NR3> 000.0000~999.9999E± X Example CALC:SCAN:LIM:UPP 1.37,kohm Sets the upper limit to 1.37kΩ. CALC:SCAN:LIM:UPP? >1.3700E+3 Returns the upper limit as 1.37kΩ.
GOM-804 & GOM-805 使用手册 存储指令 MEMory:CLEar Query Description Clears the data from the selected memory slot. Syntax MEMory:CLEar <NR1> Parameter <NR1> 1~20 Example MEM:CLE 1 Clear data from memory slot 1. MEMory:RECall Query Description Recalls the settings from the selected memory slot.
Page 124
GOM-804 & GOM-805 使用手册 Example MEM:STAT? > NFFNN-NNNNN-NNNNN-NNNNN Indicates that memory slots 2 and 3 have data and that all other memory slots are empty. 1 2 4...
GOM-804 & GOM-805 使用手册 Sense 指令 SENSe:AUTo Query Description Sets or returns the auto-range state. Syntax SENSe:AUTo <NR1> | {OFF|ON} Query Syntax SENSe:AUTo? Parameter/ <NR1> 0:OFF. Return parameter 1:ON. Auto-Range is off. Auto-Range is on. Example SENS:AUT ON Sets auto-range mode on.
GOM-804 & GOM-805 使用手册 SENSe:REL:DATa Query Description Sets or returns the relative value for the relative function. Syntax SENSe:REL:DATa <NRf> Query Syntax SENSe:REL:DATa? Parameter <NRf> 0.0000~500.00 The unit will be auto set by the present range. Return parameter <NR3> ± 0.0000~5.1000E± X Example SENS:REL:DAT 490.32...
Page 128
GOM-804 & GOM-805 使用手册 Parameter/ <NR1> 0:OFF. Return parameter 1:ON. Turn the real time function off. Turn the real time function on. Example SENS:REAL:STAT ON Turns the real time function on. 1 2 8...
GOM-804 & GOM-805 使用手册 系统指令 SYSTem:AVERage:DATa Query Description Sets or returns the number of measurements used for the average function. Syntax SYSTem:AVERage:DATa <NR1> Query Syntax SYSTem:AVERage:DATa? Parameter/ <NR1> 2~10 Return parameter Example SYST:AVER:DAT 5 5 measurements are used to perform the average function.
GOM-804 & GOM-805 使用手册 SYSTem:ERRor Query Description Returns the current system error, if any. Query Syntax SYSTem:ERRor? Error number,”Error message” Return parameter <String> Example SYST:ERR? >0,”No error”. Indicates that there is no error message. SYSTem:HANDler Query Description Sets or returns the handler state.
GOM-804 & GOM-805 使用手册 SYSTem:LFRequency Query Description Sets or returns the frequency setting for the line filter. Syntax SYSTem:LFRequency {AUTO | 50 | 60} Query Syntax SYSTem:LFRequency? Parameter/ AUTO The frequency setting for the line Return parameter filter is automatically detected.
GOM-804 & GOM-805 使用手册 Example SYST:MDEL:DAT 1.105 Sets the delay time of measure is 1.1s. SYST:MDEL:DAT? >001.100 Returns the measurement delay as 1.1s. SYSTem:MDELay:STATe Query Description Sets or returns the measurement delay function state. Syntax SYSTem:MDELay:STATe <NR1> | {OFF|ON} Query Syntax...
GOM-804 & GOM-805 使用手册 温度指令 TEMPerature:AMBient:DATa Query Description Sets or returns the user-set ambient temperature value for the temperature compensation and the temperature conversion function. Syntax TEMPerature:AMBient:DATa <NRf> Query Syntax TEMPerature:AMBient:DATa? Parameter <NRf> -50.0~399.9 (Unit: º C) Return parameter <NR2>...
GOM-804 & GOM-805 使用手册 TEMPerature:COMPensate:COEFficient Query Description Sets or returns the temperature coefficient for temperature compensation function. Syntax TEMPerature:COMPensate:COEFficient <NR1> Query Syntax TEMPerature:COMPensate:COEFficient? Parameter/ <NR1> -9999~+9999 Return parameter Example TEMP:COMP:COEF 3930 Sets the temperature coefficient to 3930ppm. TEMPerature:COMPensate:CORRect Query Description Sets or returns the reference temperature for the temperature compensation function.
GOM-804 & GOM-805 使用手册 TEMPerature:CONVersion:DISPlay Query Description Sets or returns the temperature display mode for the temperature conversion function. Syntax TEMPerature:CONVersion:DISPlay <NR1> Query Syntax TEMPerature:CONVersion:DISPlay? 1:ΔT Parameter/ <NR1> Return parameter Example TEMP:CONV:DISP 1 Sets the temperature display mode for the temperature conversion function is ΔT.
GOM-804 & GOM-805 使用手册 Example TEMP:CONV:RES 10.00,maohm Sets initial resistance value to 10.00MΩ. TEMP:CONV:RES? >10.0000E+6 Returns the initial resistance as 10.00MΩ. TEMPerature:CONVersion:TEMPerature Query Description Sets or returns the initial temperature for the temperature conversion function. Syntax TEMPerature:CONVersion:TEMPerature <NRf> Query Syntax...
GOM-804 & GOM-805 使用手册 Example TEMP:STAT ON Sets the temp function on. TEMPerature:UNIT Query Description Sets or returns the temperature unit. (Only used for the display readback.) Syntax TEMPerature:UNIT {DEGC|DEGF} Query Syntax TEMPerature:UNIT? Parameter/ DEGC º C Return parameter DEGF º...
GOM-804 & GOM-805 使用手册 触发指令 READ Query Description Returns the measurement value. Query Syntax READ? Return parameter <NR3> ± 0.0000~5.1000E± X Example READ? >+2.2012E+0 Returns the measurement. MEASure<X> Query Description Returns the results of the selected channel in the scan mode, including HI/LO/IN and value.
GOM-804 & GOM-805 使用手册 自定义指令 USERdefine<X>:ACTive Query Description Sets or returns the active output state of the selected Userdefine pin. Syntax USERdefine<X>:ACTive <NR1> Query Syntax USERdefine<X>:ACTive? Parameter/ <X> Userdefine pin 1~2 Return parameter <NR1> 1:active low state 2:active high state...
GOM-804 & GOM-805 使用手册 Parameter/ <X> Userdefine pin 1~2 Return parameter <NR1> 1:off(only judge first data) 2:logical and. 3:logical or. Example USER1:LOG 1 Sets the operator of userdefine1 to off. (I.e., only the first operand determines the output of userdefine1.) USERdefine<X>:SEConddata...
GOM-804 & GOM-805 使用手册 *IDN Query Description Returns the manufacturer, model No., serial number and system version number. Query Syntax *IDN? Return parameter <String> 31 characters Example *IDN? >GWINSTEK,GOM805,GXXXXXXXX,V1.00. *OPC Query Description Sets or returns the operation complete bit (bit0) in SERS (Standard Event Status Register) when all pending operations are completed.
GOM-804 & GOM-805 使用手册 Parameter/ <NR1> 0~255 Return parameter Example *SRE 7 Sets the SRER to 00000111 *SRE? >3 SRER=00000011 *STB Query Description Returns the SBR (Status Byte Register) contents. Query Syntax *STB? Return parameter <NR1> 0~255 Example *STB? >81...
Page 149
GOM-804 & GOM-805 使用手册 状态系统 The diagram below is a description of the status system. Questionable Data Status Register Event Enable Voltage Overload Not Used Not Used Not Used Output Not Used Buffer Temp Overload Not Used Not Used Not Used...
Page 159
GOM-804 & GOM-805 使用手册 尺寸 G O M -8 0 5 DC Milliohm Meter Compare Binning TCONV TEMP Enter Speed Scan Trigger GUARD Display Local Diode Drive Range POWER SOURCE SENSE SENSE SOURCE 275.5 214.0 282.9 222.8 1 59...
Page 160
No. 7-1, Jhongsing Road, Tucheng Dist., New Taipei City 236, Taiwan Tel: +886-2-2268-0389 Fax: +866-2-2268-0639 Web: www.gwinstek.com Email: marketing@goodwill.com.tw GOOD WILL INSTRUMENT (SUZHOU) CO., LTD. No. 521, Zhujiang Road, Snd, Suzhou Jiangsu 215011, China Tel: +86-512-6661-7177 Fax: +86-512-6661-7277 Web: www.instek.com.cn Email: marketing@instek.com.cn...
Page 161
索引 索 引 Binning function measure delay ............ 61 PWM duty ............68 setting ..............46 setting ..............60 Characteristics ............. 10 temperature unit ..........65 Compare function trigger delay ............63 setting ..............41 trigger edge ............64 Declaration of conformity ......... 159 Power supply safety instructions......
Page 162
GOM-804 & GOM-805 使用手册 beep ..............76 Temperature conversion brightness ............72 setting ..............56 external IO ............73 Temperature measurement handler mode ............74 reference ............152 interface ............. 71 TFT-LCD overview ..........19 power on settings ..........70 Tilt stand .............
Need help?
Do you have a question about the GOM-804 and is the answer not in the manual?
Questions and answers