Related Manuals for TAKE-A-LABEL TAL-3100C
Summary of Contents for TAKE-A-LABEL TAL-3100C
- Page 1 TAKE-A-LABEL, Inc. Operation Manual TAL-3100C Tamp Applicator TAKE-A-LABEL 16900 Power Dr. Nunica, MI 49448 Phone (616) 837-9300 Fax (616) 837-9301 www.take-a-label.com Email: sales@take-a-label.com...
-
Page 2: Machine Startup
TAL-3100C Tamp Applicator Machine Startup: 1. Mount the TAL-3100C on an appropriate mounting stand. Be sure to mount the labeler using only the mounting arms. 2. Plug the TAL-3100C directly into a 110 VAC 15-amp Grounded outlet. Extension cords may result in improper labeler operation and are not recommend by Take-A-Label, Inc. -
Page 3: Label Setup
Label Setup: The label advance potentiometer resides on top of the TAL-3100C electrical housing. The purpose is to adjust the stopping position of the label with respect to the peel plate. With the label advance pot turned all the way counterclockwise the photo eye will stop the applicator instantly when it senses a gap. - Page 4 Tamp Head Placement: 1. The tamp head placement is crucial for consistent label application. 2. The vertical gap between the peel plate and tamp pad should range from 0”-1/32”. If not loosen the nut at the base of the tamp cylinder rod, and unthread to lower the tamp pad or screw in the rod to raise the tamp pad height.
- Page 5 Air Assist Tube Placement: 1. The air assist tube is used to assist the label out onto the vacuum pad. As a rule of thumb, the blast pattern from this tube should be directed at a 30° angle onto the vacuum pad. This angle may vary due to several factors, as a result different blast angles may have to be experimented with.
- Page 6 Teaching the photo eye: 1. It is recommended that you teach the photo eye (18) with every new roll of labels used. 2. Remove one label from the webbing and place the webbing only in the photo eye. 3. Press and hold the “Normal” button on photo eye for 3 seconds. When the lights finish flashing the photo eye is taught.
- Page 7 Tamp Head Dwell Time – Label Advance Delay Adjusting Dwell Time: • Knob A: increases or decreases the time before the label is advanced on to the tamp pad. This variance will occur after activating the footswitch and beginning the cycle. Adjusting Label Advance Delay •...
- Page 8 Recommended Spare Parts for the TAL-3100C Qty. Description Part # Pinch Roller 31002 Waist wind Clip 45131 Unwind Disc 45136 Motor 30031 Photo Cell Label Sensor 30106 Drive “V” Belt 31267 Circuit Board 31057 Unwind Felt Pad 72618 Main Fuse...
-
Page 10: Parts List
Connecting Bracket 31015 Plastic Bearing 31017 Long Bushing 31020 Cylinder Cross Mount Plate 31021 Cylinder Mount Plate 31029 Rewind Bushing 31053 T-Nut/ Bond/8020 31140 TAL-3100C/W Housing 31141 TAL-3100C/W Cover 31057 Control Board 31059 Label Advance 31060 Rewind Bracket 31102 Driver Roller... - Page 11 Unwind Disk 25212 Power Cord 72618 White Felt 4x4 81830 Shaft Caps 81912 Small Cord Grip 31144 TAL-3100C Threading Label 58 31146 TAL-3100C Name Label 31824 Shoulder Bolt 10-32 45136 Unwind Disk 25102 3/8” Black Plug 30208 Photo Eye Product Sensor...