Table of Contents
Advertisement
Quick Links
PRODUCT DESCRIPTION
The PCE4550AH is a 5G dual band concurrent 3T3R PCIe module base
on QCA9880 commercial grade solution.
P
S
RODUCT
PECIFICATION
RF Specification
Radio 1
Frequency Band
Data rate
Receive Sensitivity (Typical)
802.11 a/n/ac Module
PCE4550AH
User's Manual
Support 5GHz
802.11a/n/ac
5.190~5.795GHz
1300Mbps
802.11a
802.11a/ n_HT20
802.11n_HT40
802.11ac_HT80
≤ -94dBm@6Mbps
≤ -76dBm@54Mbps
≤ -93dBm @ MCS0/8/16
≤ -74dBm @ MCS7/15/23
≤ -92dBm @ MCS0/8/16
≤ -72dBm @ MCS7/15/23
≤ -89dBm@MCS0
≤ -64dBm@MCS9
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for SENAO PCE4550AH
Summary of Contents for SENAO PCE4550AH
- Page 1 802.11 a/n/ac Module PCE4550AH User’s Manual PRODUCT DESCRIPTION The PCE4550AH is a 5G dual band concurrent 3T3R PCIe module base on QCA9880 commercial grade solution. RODUCT PECIFICATION RF Specification Support 5GHz Radio 1 802.11a/n/ac Frequency Band 5.190~5.795GHz Data rate 1300Mbps ≤...
- Page 2 Type Connector 5150~5250MHz 5250~5350MHz 5470~5725MHz 5725~5850MHz Dipole 3dBi 3dBi 3dBi 3dBi Dipole 5.5 dBi 5.5 dBi 5.5 dBi 5.5 dBi PIFA 6 dBi 6 dBi 6 dBi 6 dBi Note: The EUT has three antennas. (3TX/3RX) Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment.
- Page 3 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
- Page 4 This device is intended only for OEM integrators under the following conditions: The antenna must be installed such that 20 cm is maintained between the antenna and users, and The transmitter module may not be co-located with any other transmitter or antenna, As long as 2 conditions above are met, further transmitter test will not be required.
- Page 5 This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: U2M-PCE4550AH”.
- Page 6 Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.
- Page 7 Professional installation instruction 1. Installation personal This product is designed for specific application and needs to be installed by a qualified personal who has RF and related rule knowledge. The general user shall not attempt to install or change the setting. 2.
Need help?
Do you have a question about the PCE4550AH and is the answer not in the manual?
Questions and answers