Makita DUC204 Instruction Manual page 15

make exposed metal parts of the power tool
"live" and
the operator
shock.
4. Wear safety glasses and hearing protection.
Further protective equipment for
head, hands,
feet is
Adequate protective clothing
reduce personal
flying debris or accidental contact with
the saw chain.
5. Always keep proper footing.
6. When cutting a limb that is under tension be
alert for spring back.
tension in
fibres is released the spring loaded
limb may strike the operator and/or throw the
chain saw out of control.
7. Use extreme caution when cutting brush and
saplings. The
may catch
chain and be whipped toward you or pull
you off balance.
8. Carry the chain saw by the front handle with
the chain saw switched off and away from
your body. When transporting or storing the
chain saw always fit the guide bar cover.
Proper handling of the chain saw will reduce the
likelihood of accidental contact with the moving
saw chain.
9. Follow instructions for lubricating, chain
tensioning and changing accessories.
Improperly tensioned or lubricated chain may
either break or increase the chance for kickback.
10. Keep handles dry, clean, and free from oil and
grease. Greasy, oily handles are slippery causing
loss of control.
11. Cut wood only. Do not use chain saw for
purposes not intended. For example: do not use
chain saw for cutting plastic, masonry or nonwood
building materials. Use of the chain saw for
operations different than intended could result in a
hazardous situation.
12. Causes and operator prevention of kickback:
Kickback may occur when the nose or tip of the
guide bar touches
or when
closes in and pinches the saw chain in the
cut. Tip contact
cases may
sudden reverse reaction, kicking the
guide bar up and back towards the operator.
Pinching the saw chain along the top of the guide
bar may push the guide bar rapidly back towards
the operator. Either of these reactions may cause
you to lose control of the saw which could result in
serious personal injury.
rely exclusively upon
safety devices built into your saw. As a
chain saw user, you should take several steps to
could give
an electric
legs and
recommended.
will
injury by
When the
the wood
slender material
the saw
an object,
the wood
in some
cause a
Do not
the
15 ENGLISH
keep your cutting jobs
accident or
the result of tool misuse and/or incorrect operating
procedures or conditions and can be avoided by
taking proper precautions as given below:
•
Maintain a
with thumbs
encircling the chain saw handles, with both
hands on the saw and position your body
and arm to allow you to resist kickback
forces. Kickback forces can be controlled by
the operator, if proper precautions are taken.
Do not let go of the chain saw.
►
Fig.1
•
Do not
do not
shoulder height.
prevent unintended tip contact and
enables better control of the chain saw in
unexpected situations.
•
Only use
bars and
by the
Incorrect replacement bars and chains
may cause chain breakage and/or kickback.
•
Follow the
sharpening and
instructions for the saw chain. Decreasing
the depth gauge height can lead to
increased kickback.
13. Before starting work, check that the chain saw
is in proper working order and that its
condition complies with the safety regulations.
Check in particular that:
•
The chain
working properly;
•
The run-down brake
working properly;
•
The bar
sprocket cover
correctly;
•
The chain
sharpened and
accordance with the regulations.
14. Do not start the chain saw with the chain
cover being installed on it. Starting the chain
saw with the chain cover being installed on it may
cause the chain cover to thrown out forward
resulting in personal
damage to
the operator.
Top handle chainsaw specific safety
warnings
1. This chain saw is designed especially for tree
care and surgery. The chain saw is intended to
be used by properly trained persons only.
Observe all instructions, procedures and
recommendations from the relevant
professional organization. Otherwise fatal
free from
injury. Kickback is
firm grip,
and fingers
overreach and
cut above
This helps
replacement
chains specified
manufacturer.
manufacturer's
maintenance
brake is
is
and the
are fitted
has been
tensioned in
injury and
objects around