Summary of Contents for AAMP Global EchoMaster Pro FC-GMHD102-MC
- Page 1 Installation Guide Integrated Blindspot Safety System Select 2015-2018 GM vehicles with 7” radio display...
-
Page 2: Prior To Installation
Installation Guide FC-GMHD102 / FC-GMLD102 Integrated Safety System Prior to Installation Cover all surfaces with tape or plastic protection film to protect against scratching and damage. EchoMaster is in no way responsible for any damage that may incur during installation. This product has been validated in the vehicles listed on the application guide only. -
Page 3: Suggested Tools
Installation Guide FC-GMHD102 / FC-GMLD102 Integrated Safety System Vehicle Preparation & Protection CAUTION It is recommended to perform this installation with the vehicle’s battery disconnected. Please consult the vehicle’s owner’s manual for proper battery disconnection procedure. Do not disconnect ANY airbag connectors or indicators. Doing so may result in activating a diagnostic code. -
Page 4: Removing The Radio
Installation Guide FC-GMHD102 / FC-GMLD102 Integrated Safety System Removing the Radio Step 1 Using a nylon trim removal tool, remove the LCD display trim panel. Step 2 Remove the 4 x 7mm bolts from around the LCD display. Once bolts have been removed, remove the unit from the dash. -
Page 5: Removing The Door Panel(S)
Installation Guide FC-GMHD102 / FC-GMLD102 Integrated Safety System Removing the Door Panel(s) Step 1 Remove the plastic cover from the door pull and remove the 2 x 7mm bolts. Step 2 Remove the plastic cover from the door release handle and remove the 1 x 7mm bolt underneath. - Page 6 Installation Guide FC-GMHD102 / FC-GMLD102 Integrated Safety System Removing the Door Panel(s) - continued Step 4 Using a nylon trim removal tool, unsnap the 4 clips and remove the plastic trim from the armrest and set aside. Once the trim is removed, remove the 7mm bolt found underneath the trim.
- Page 7 Installation Guide FC-GMHD102 / FC-GMLD102 Integrated Safety System Removing the Door Panel(s) - continued Step 7 Unclip door handle release assembly by pressing on top and removing cable from handle assembly. Set the door panel aside. Repeat the steps above for the opposite door panel.
- Page 8 Installation Guide Heavy Duty Mirror FC-GMHD102 / FC-GMLD102 Integrated Safety System Removing the Heavy Duty Mirror PLEASE NOTE Fully extend the mirror for removal and camera installation. Step 1 Using nylon trim removal tool remove top arm cover of mirror assembly. PLEASE NOTE Separate the camera mini connector from the small power supply to route through the...
- Page 9 Installation Guide FC-GMHD102 / FC-GMLD102 Integrated Safety System Step 3 Using a nylon trim removal tool remove the bottom mirror cap from the mirror assembly. PLEASE NOTE Using two nylon tools to work the cover off is recommended. Be sure not to scar plastic from mirror assembly.
- Page 10 Installation Guide Light Duty Mirror FC-GMHD102 / FC-GMLD102 Integrated Safety System Removing the Light Duty Mirror Using a nylon trim removal tool remove the mir- ror cap from the mirror assembly. There are 6 tabs holding the mirror cap on to the mirror.
- Page 11 Installation Guide Light Duty Mirror FC-GMHD102 / FC-GMLD102 Integrated Safety System Routing the Camera Harness Route the camera Route the camera Route the camera harness into the small harness in to the channel harness to the opening on the mirror towards the hinge where opening in the hinge.
- Page 12 Installation Guide FC-GMHD102 / FC-GMLD102 Integrated Safety System Route Camera Extension Harness Starting from inside door, route the female end of the cable through the round factory grommet (must cut hole). Route the cable through the rubber door boot (easily done using a long zip tie taped to harness).
- Page 13 Installation Guide FC-GMHD102 / FC-GMLD102 Integrated Safety System Route Camera Extension Harness Route 16-pin main camera extension cable down below the dash. This should pass through hole located in the back portion of the radio cavity and exit from bottom of dash. For vehicles with a center council, route the camera harness towards the glove compartment opening.
-
Page 14: Module Connections
Installation Guide FC-GMHD102 / FC-GMLD102 Integrated Safety System Module Connections Connect 8-pin power t-harness to module. Connect 16-pin main camera extension cable to module. Fasten harnesses to the bracket using zip ties through the holes provid- Select vehicle year using dip switches. u 2018 dip switch 1 down 2 up... - Page 15 Installation Guide FC-GMHD102 / FC-GMLD102 Integrated Safety System Bottom side of the connector Remove GREY connector from behind Release the locking TABS on the the radio display panel. Flip connector left and right side of the connector. over to access the bottom row. Fold locking TAB up.
- Page 16 Installation Guide FC-GMHD102 / FC-GMLD102 Integrated Safety System LVDS Connection Grey Gold Disconnect the con- nector from the radio module along BLACK LVDS with the connector BLUE with the cable. Grey Gold Connect the connector T-harness to the radio module and the radio harness.
-
Page 17: Wiring Diagram
Installation Guide FC-GMHD102 / FC-GMLD102 Integrated Safety System Wiring Diagram Illustrations are typical and may not match exact vehicle details email - support@aampglobal.com (US) tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast) email - technical.eu@aampglobal.com (Europe) -
Page 18: To Access The Menu
Installation Guide FC-GMHD102 / FC-GMLD102 Integrated Safety System To Access the Menu Press and hold the ”HOME” button for three seconds to enter the camera menu. Use the touch screen select your desired view. Press “HOME” to return to the previous screen. PLEASE NOTE The camera menu is accessible after 7 seconds while in reverse. - Page 19 Installation Guide FC-GMHD102 / FC-GMLD102 Integrated Safety System Activating NON-Factory Backup Camera option From the main camera menu From the main camera menu press and hold the on the lower right hand corner of the screen. Installer setup screen select Enable Aftermarket Backup Camera if no factory back up camera installed.
- Page 20 Unit 25B, Woolmer Way, Bordon, Hampshire, United Kingdom, GU35 9QE email - support@aampglobal.com (US) tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast) email - technical.eu@aampglobal.com (Europe) tel - +44(0)1420 487110 (sales) - +44(0)1420 470618 (technical) EchoMaster is a Power Brand of AAMP Global. IUG-FC-GMHDLD102-MC REV. 032818 EchoMaster.com...