Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Kasda KW58193
Summary of Contents for Kasda KW58193
- Page 1 KW58193 Wireless ADSL Modem User Manual...
- Page 2 Wireless ADSL Modem USER MANUAL NOTICE This document contains proprietary information protected by copyright, and this Manual and all the accompanying hardware, software, and documentation are copyrighted. All rights are reserved. No part of this document may be photocopied or reproduced by mechanical, electronic, or other means in any form.
-
Page 3: Table Of Contents
Content 1 OVERVIEW ..........................1 ............................1 1.1 F EATURES Data rate ..........................1 1.1.1 ADSL Compliance ........................1 1.1.2 Wireless ........................... 1 1.1.3 1.1.4 Network Protocol and Features ..................2 1.1.5 ATM Capabilities ........................2 FIREWALL ..........................2 1.1.6 Management Support ...................... - Page 4 Wireless ADSL Modem USER MANUAL Advanced Settings ....................... 20 5.3.2 5.3.3 Security ..........................22 ..........................26 5.4 M ANAGEMENT 5.4.1 TR069 ............................26 5.4.2 Port Mapping ..........................27 5.4.3 Reset Router ..........................29 APPENDIX FREQUENT ASKED QUESTIONS ............... 30...
-
Page 5: Overview
Wireless ADSL Modem USER MANUAL 1 Overview Thank you for choosing our product. The KW58193 Wireless ADSL Router uses Realtek’s CPE solution that fully complies with ADSL, ADSL2 ，ADSL2+ and IEEE802.11b/g/n standards. It will provide your SOHO with convenient Internet access. -
Page 6: Network Protocol And Features
Wireless ADSL Modem USER MANUAL 1.1.4 Network Protocol and Features Ethernet to ADSL Self-Learning Transparent Bridging Internet Control Message Protocol (ICMP) IP Static Routing Routing Information Protocol (RIP, RIPv2) Network Address Translation (NAT) Virtual Server, Port Forwarding ... -
Page 7: Management Support
Wireless ADSL Modem USER MANUAL Denial of Service Prevention (DoS) 1.1.7 Management Support Web Based GUI Upgrade or update via FTP/HTTP Command Line Interface via Telnet Diagnostic Test Firmware upgrade-able for future feature enhancement 1.1.8 Operating System Support ... -
Page 8: Factory Defaults
Wireless ADSL Modem USER MANUAL Subscription for ADSL service. Your ADSL service provider should provide you with at least one valid IP address (static assignment or dynamic assignment via dial-up connection). One or more computers, each contains an Ethernet 10/100M Base-T network interface card (NIC). -
Page 9: Hardware Description
Wireless ADSL Modem USER MANUAL 2 Hardware Description Front Panel Color Function On: Power on Green Off: No power On: LAN link established and active via LAN port Green Blinking: ADSL data activity occurs Off: No LAN link via LAN port On: The wireless module is ready and idle Green Blinking: Data transmitting or receiving over WLAN... - Page 10 Wireless ADSL Modem USER MANUAL Rear panel Port Function Connect the device to an ADSL telephone jack or splitter using a RJ-11 telephone cable Connect the device to user’s PC's Ethernet port, or to the ETH1-4 uplink port on user’s hub/switch, using a RJ-45 cable Reset System reset or reset to factory defaults A convenient way for WPS set.
-
Page 11: Hardware Installation
Wireless ADSL Modem USER MANUAL 3 Hardware Installation This chapter shows user how to connect Router. Meanwhile, it introduces the appropriate environment for the Router and installation instructions. Using a telephone line to connect the DSL port of ROUTER to the Modem port of the splitter, and using a other telephone line connect user’s telephone to the PHONE port of the splitter, then connect the wall phone jack to the LINE port of the splitter. -
Page 12: Pc Configuration Guide
Wireless ADSL Modem USER MANUAL 4 PC Configuration Guide Local PC Configuration in Windows 95, 98, ME, XP In the Windows task bar, click the “Start” button, point to “Settings”, and then click “Control Panel”. Double-click the “Network” icon. On the “Configuration” tab, select the TCP/IP network associated with user’s network card and then click “Properties”. -
Page 13: Local Pc Configuration In Windows Vista
Wireless ADSL Modem USER MANUAL Local PC Configuration in Windows Vista 1. Go to Start. Click on Network. 2. Then click on Network and Sharing Center at the top bar. 3. When the Network and Sharing Center window pops up, select and click on Manage network connections on the left window column. -
Page 14: Web-Based Management Guide
Wireless ADSL Modem USER MANUAL 5 Web-based Management Guide In order to use the web-based management software it will be necessary to use a computer that occupies the same subnet as the Router. The simplest way to do this for many users will be to use DHCP server that is enabled by default on the Router. 5.1 LAN setting page Launch a web browser, such as Internet Explorer, and then use http://192.168.1.1... -
Page 15: Pppoe(Ppp Over Ethernet)
Wireless ADSL Modem USER MANUAL From Setup, click WAN, configure the parameters for the channel operation modes of your ADSL Router. 5.2.1 PPPoE(PPP over Ethernet) PPPoE (Point to Point Protocol over Ethernet) provides access control and billing functionality in a manner similar to dial-up services using PPP. The router bridges a PPP session over Ethernet (PPP over Ethernet, RFC2516) from your computer to an ATM PVC (Permanent Virtual Circuit) which connects to ADSL Access Concentrator where the PPP session terminates. - Page 16 Wireless ADSL Modem USER MANUAL Item Description VPI/VCI Enter the PVC that your ISP gives you. NAPT extends the notion of NAT one step further by also translating the transport identifier (TCP and UDP port numbers, ICMP query Enable NAPT identifiers).
-
Page 17: Pppoa(Ppp Over Atm)
Wireless ADSL Modem USER MANUAL single public IP address. IGMP(Internet Group Management Protocol) is a network-layer protocol used to establish membership in a Multicast group- it is not Enable IGMP used to carry user data. IGMP version 2 (RFC 2236) is an improvement over version 1 (RFC 1112) but IGMP version 1 is still in wide use. - Page 18 Wireless ADSL Modem USER MANUAL Item Description VPI/VCI Enter the PVC that your ISP gives you. NAPT extends the notion of NAT one step further by also translating the transport identifier (eg TCP and UDP port numbers, ICMP query Enable NAPT identifiers).
-
Page 19: Bridged
Wireless ADSL Modem USER MANUAL in wide use. PPP settings: User name & Enter the user name and password that your ISP gives you. password Continuous: If you want to access the Internet all the time, select Continuous type. Connect on Demand: Select this type when you don’t want the PPP Settings: connection up all the time and specify an idle time-out in the Type... -
Page 20: Lan Settings
From LAN, Configure the DSL Router’s IP Address and Subnet Mask for LAN interface. In this page, you can use DHCP (Dynamic Host Configuration Protocol) to control the assignment of IP addresses on your local network (LAN only).KW58193 support IPv4 /IPv6 dual stack. - Page 21 Wireless ADSL Modem USER MANUAL Item Description This is the IP address that other devices on your local network will IP address use to connect to the modem. The default is 192.168.1.1. Subnet mask This defines the size of your network. The default is 255.255.255.0. Select this option is to let the device use a second IP on the LAN interface.
- Page 22 Wireless ADSL Modem USER MANUAL 10.0.0.1. Type the subnet mask. IGMP Snooping is a method that actually “snoops” or inspects IGMP traffic on a switch. When enabled, the switch will watch for IGMP IGMP snooping messages passed between a host and a router, and will add the necessary ports to its multicast table, ensuring that only the ports that require a given multicast stream actually receive it.
-
Page 23: Wlan Setting
Wireless ADSL Modem USER MANUAL 5.3 WLAN Setting 5.3.1 Basic Option Description A check box that enables or disables the wireless LAN interfaces. The default is Enable wireless to enable wireless communications. This is the range of frequencies the gateway will use to communicate with Band user’s wireless devices. -
Page 24: Advanced Settings
Wireless ADSL Modem USER MANUAL access the Internet. BSSID Displays the gateway's wireless MAC address. (User may need this address if user is using WDS or multiple gateways.) Click Apply to save changes. Country Drop-down menu that allows selection of specific channel. 5.3.2 Advanced Settings This page is where user specifies a number of advanced settings for wireless... - Page 25 Wireless ADSL Modem USER MANUAL Warning: The settings shown above are default settings. Changes made to these items can cause wireless communication problems. Field Description A threshold, specified in bytes, that determines whether packets will be fragmented and at what size. On an 802.11 connection, packets that are larger the fragmentation threshold are split into smaller units suitable for the circuit size.
-
Page 26: Security
Wireless ADSL Modem USER MANUAL XPress™ Technology is a feature in which two of our devices can communicate with each other at twice the normal rate. XPress™ 54g+ is a technology that achieves higher throughput with frame-bursting. With Technology 54g+ enabled, aggregate throughput (the sum of the individual throughput of each network client) improves by up to 25% in 802.11g-only networks, and up to 75% in mixed networks containing both 802.11g and 802.11b equipment. - Page 27 Wireless ADSL Modem USER MANUAL 3.Enable WPS as below. 4. Set Start PBC and click Save/Changes.
- Page 28 Wireless ADSL Modem USER MANUAL 5.Now you can use a wireless adaptor with WPS function and the WPS button to connect to access the Internet. 6. To configure security features for the Wireless interface, please open Security item from Wireless menu. This web page offers nine authentication protocols for user to secure user’s data while connecting to networks.
- Page 29 Wireless ADSL Modem USER MANUAL WEP —WEP is an encryption scheme that is used to protect user’s wireless data communications. WEP uses a combination of 64-bit keys or 128-bit keys to provide access control to user’s network and encryption security for every data transmission.
-
Page 30: Management
Wireless ADSL Modem USER MANUAL 5.4 Management 5.4.1 TR069 WAN Management Protocol (TR-069) allows a Auto-Configuration Server (ACS) to perform auto-configuration, provision, collection, and diagnostics to this device. Select Configure TR-069 from Advanced->CWMP. URL: URL for the CPE to connect to the ACS using the CPE WAN Management Protocol. And through ACS (Auto-Configuration Server) you can perform auto-configuration, provision, collection, and diagnostics to this router. -
Page 31: Port Mapping
Wireless ADSL Modem USER MANUAL making a connection to the ACS using the CPE WAN Management Protocol. This username is used only for authentication of the CPE. Connection Request Password: Password used to authenticate the CPE when making a connection to the ACS using the CPE WAN Management Protocol. This password is used only for authentication of the CPE. - Page 32 Wireless ADSL Modem USER MANUAL Enable it and select Group1 as below. Set as below.
-
Page 33: Reset Router
Wireless ADSL Modem USER MANUAL Click Apply and you’ll see the following screen. Click Save, Now you can use LAN1 interface for IPTV and other Ethernet interface for internet. Note: If you want to cancel all modification that you do on the Router, please select from “AdminCommit/RebootFactory Default ConfigurationReboot”... -
Page 34: Appendix Frequent Asked Questions
Wireless ADSL Modem USER MANUAL Appendix Frequent Asked Questions Q: None of the LEDs are on when you power on the ADSL router? A: Please make sure what you use is the power adaptor attached with the ADSL router package，and check the connection between the AC power and ADSL router. Q: DSL LED does not turn on after connect telephone line? A: Please make sure what you use is the standard telephone line (as attached with the package), make sure the line is connected correctly and check whether there is poor... - Page 35 Wireless ADSL Modem USER MANUAL Q: PC cannot browse Internet web page? A: Please make sure DNS server appointed to the PC is correct. You can use ping application program to test whether the PC can connect to the DNS server of the ADSL operator.