GP -4019BC User Manual

page of 28

/ 28
Bookmarks

Quick Links

Download this manual

GP-4019BC

BRUSH CUTTER

USER MANUAL

Note: Please read the following instructions before use. This book contains important information on SAFETY, ASSEMBLY, OPERATION

& DISCLAIMER: DUE TO CONSTANT UPGRADATION, FEATURES AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Need help?

Do you have a question about the GP-4019BC and is the answer not in the manual?

Questions and answers

Summary of Contents for GP GP-4019BC

Page 1 GP-4019BC BRUSH CUTTER USER MANUAL Note: Please read the following instructions before use. This book contains important information on SAFETY, ASSEMBLY, OPERATION & DISCLAIMER: DUE TO CONSTANT UPGRADATION, FEATURES AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE...
Page 2 SAFETY FIRST Instructions contained in warnings within this manual marked with a “ ” symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury and for this reason you are requested to read all such instructions carefully and follow them without fail. NOTES ON TYPES OF WARNINGS IN THE MANUAL WARNING This mark indicates instructions, which must be followed in order to prevent accidents, which...
Page 3 SYMBOLS ON THE MACHINE peration and maintenance symbols are carved in relief on the machine. FOR SAFE OPERATION AND MAINTENANCE SYMBOLS ARE CARVED IN g to these indications, please be careful not to make a mistake. RELIEF ON THE MACHINE. According to these indications, please be careful not to make a mistake.
Page 4 ASSEMBLY 1 Specifications Model GP4019BC Handle model duble-hand Weight <7.5kg Length 1800mm Size Width 300mm Height 260mm Nylon cutting head , 3teeth, 4teeth, 8teeth, 40 teeth Blade blade Transmission method Automatic centrifugal clutch Rate for slowing down 1.25 Edge rolling direction counterclockwise Model 1E40F...
Page 5 (2) Connect the body with engine, keep oil tank and four screws in the same direction. (3) Setting for two handles As drawing, first loosen the four screws, fix two handles from two direction, and then screw them down again. (4) Installment of cutting attachment guard Please look at the picture, fix the cutting attachment guard on the tail of gear case, and then screw down the round screw.
Page 6 rom drowsiness as a result of having taken cold medicine, or m drowsiness as a result of having taken cold medicine, or when a possibility exists that your judgment might be impaired e when a possibility exists that your judgment might be impaired when a possibility exists that your judgment might be impaired ot be able to operate the brush cutter properly and in a safe t not be able to operate the brush cutter properly and in a safe...
Page 7 Non-slip-sole work boots e (for collaboration or emergency) Ear protectors (esp. for long-time operation) t or saw (for removal of obstacles) And you should carry with you things as follows. rush cutter when wearing pants with loose cuffs, Attached tools and files ndals or when barefoot.
Page 8 TARTING THE ENGINE ok around to make sure that no obstacles exist within NOTES ON STARTING THE ENGINE 5m or less around brush cutter. Take a careful look around to make sure that no the brush cutter onto the ground in a flat clear area obstacles exist within a perimeter of 15m or less y in place so as to ensure that neither the blades nor around brush cutter.
Page 9 OPERATION SAFETY PRECAUTIONS Grip the handles of the brush cutter firmly with both hands. If you suspend the work, place the throttle into the idling position. Always be sure to maintain a steady, even posture while working. Maintain the speed of the engine at the level required to perform cutting work, and never raise the speed of the engine above the level necessary..
Page 10 WARNING CONSIDERING HANDLING OF FUEL The engine of this product is designed to run on a mixed fuel, which contains highly flammable gasoline. You should never store cans of fuel or refill the fuel tank in any place where there is a boiler, stove, wood fire, electrical sparks, welding sparks, or any other source of heat or fire which might ignite the fuel.
Page 11 OPERATION STARTING THE ENGINE WARNING Keep the blade clear of everything around it as it will start moving upon the engine starts. Press carburetor cap several times with finger until oil pipe full of fuel. Please pull the air shutter switch to the closed position. If the engine stay in the place that just stopped, pull the switch to open position.
Page 12 Push the engine stopping switch. NOTE If the engine doesn’t stop after stopping the switch, close the choke so that engine will stop after a while. CUTTING WORK WARNING • Weather conditions and altitude may affect carburetor. • Do not allow anyone to stay close the brush cutter while working or adjusting the carburetor. HOW TO USE Shoulder hang As picture, hang it from left shoulder to right waist,...
Page 13 MAITAINENCE WARNING Before cleaning , inspecting, or repairing the unit, make sure that the engine has stopped and cooled down. BLADE • Check the blade and the fasteners for looseness, cracking, or bending IMPORTANCE When mounting the blade, make sure to fasten the spacer, washer and nut. AIR CLEANER Release the air cleaner cover and remove dusts,.
Page 14 SPARK PLUG Starting failure and mis-firing are often caused by a fouled spark plug. Periodically clean the spark plug, and replace with a new one required. IMPORTANCE When dismounting the plug cap, be careful not to take off the seal from the seal from the plug cap.
Page 15 1. Idle speed fuel adjusting screw Screw it down in veer then release it just one circuit which is the standard Right adjustment: quantity decrease Left adjustment: quantity increase 2. High-speed fuel adjusting screw Right adjustment: quantity decrease Left adjustment: quantity increase 3.
Page 16 Check-up before or after working Checking items Manage ways Blades A. if the screw loosen screw down B. if the blades are bad or replace them abrasion C. if the blades are attrited rub the blades or change them Safety cover A.
Page 17 MAITANENCE BEFORE STORAGE IMPORTANCE Use a dry rag to wipe any fuel which has been spilled onto the unit. Meanwhile, tighten the cover of the container. Extract fuel from the tank and run the engine until it stops naturally. Remove the spark plug and put in 1-2cc of 2-cycle oil in the engine .
Page 18 TECHNICAL PARAMETEERS Model GP-4019BC Type Brush Cutter Clutch rotate speed (r/min) 3200-3400 Drive transfer style automatic centrifugation Rotating direct of blade anticlockwise Transmission ratio 1.25 ≤80 idling dB(A) noise dB(A) ≤102 high speed racing dB(A) Model 1E40F-5A Type 1-cylinder, 2-stroke ,air- cooled Displacement (ml) 42.7...
Page 19 ACCESSORIES...
Page 20 SPARE PARTS DIAGRAM OF GP-4019BC BRUSH CUTTER...
Page 21 SPARE PARTS LIST GP-4019BC BRUSH CUTTER Part No. Description Part No. Description stop ring Φ26 GP-4019BC-T01 GP-4019BC-T26 trimmer head stop ring Φ26 GP-4019BC-T02 GP-4019BC-T27 harness clamp GP-4019BC-T03 bearing 600 GP-4019BC-T28 anti-vibration rubber GP-4019BC-T04 pinion GP-4019BC-T29 NUTM5 GP-4019BC-T05 steel plate cap...
Page 22 SPARE PARTS DIAGRAM GP-4019BC BRUSH CUTTER Part No. Description Part No. Description GP-4019BC-T51 clock pin GP-4019BC-T75 lower cap GP-4019BC-T52 handgrip GP-4019BC-T76 M6 screw GP-4019BC-T53 stop connector GP-4019BC-T77 grip, left GP-4019BC-T54 screw GP-4019BC-T78 M5 nut GP-4019BC-T55 stop connector-B GP-4019BC-T79 screw GP-4019BC-T56...
Page 23 1st Free Service Coupon ISO 9001-2015 CERTIFIED COMPANY FREE SERVICE COUPON (30 Days / 30 hrs (Which ever is earlier) Model Serial Number GP-4019BC BRUSH CUTTER PDI Date Service No. Purchase bill no. Date Dealer’s Office Seal & Signature Customer Signature.........
Page 24 1. LIMITED WARRANTY PERIOD : For a period of six months from the date of Sale / delivery of the product which ever is earlier. 2. LIMITED WARRANTY OBLIGATION : Replacement of defective part(s) by authorized dealer are free of charges. If found defective by reasons of defective material / poor workmanship, parts will be replaced and there will be no value re-imbursement.
Page 25 Warranty Card CUSTOMER COPY Purchaser’s Name & Address Date of Delivery Dealer’s Office Seal Product Name GP-4019BC BRUSH CUTTER Product Serial No. Dealer Sign Customer Sign. Invoice / DN No. I/We accept the terms and conditions of Warranty as in the Warranty Card.
Page 26 Small Maintenance. Big Savings. Small Maintenance. Big Savings. Small Maintenance. Big Savings.
Page 27 Do’s Don’ts • Always read the instruction manual supplied along with the equipments and understand the correct installation and operating procedures before attempting to use the equipments. • It is important to use the personal protection equipments such as head helmet with visor, ear defenders, goggles, safety gloves, cut resistant shoes, trousers and jackets while operating potentially dangerous machines.
Page 28 GP-4019BC BRUSH CUTTER IMPORTERS & DISTRIBUTORS RATNAGIRI IMPEX PVT LTD Annapurna House, #1/1G, 7th Cross, New Guddadahalli Mysore Road, Bangalore-560 026 Customer Care: 1800-425-3036 email: info@ratnagiriimpex.com www.ratnagiriimpex.com AN ISO 9001:2015 CERTIFIED COMPANY...