Table of Contents
Advertisement
Quick Links
A
d
v
A
d
v
I
n
s
I
n
s
E
a
E
a
November 2013, Rev 1
a
n
c
e
d
a
n
c
e
d
t
r
u
c
t
i
o
t
r
u
c
t
i
o
s
t
e
r
n
V
o
l
t
a
g
e
s
t
e
r
n
V
o
l
t
a
g
Advanced Flame 1.0 Kit
F
l
a
m
e
F
l
a
m
e
n
M
a
n
n
M
a
n
R
e
s
e
a
r
c
h
,
e
R
e
s
e
a
r
c
h
,
− 1 −
http://www.EasternVoltageResearch.com
1
.
0
1
.
0
u
a
l
u
a
l
L
L
C
L
L
C
Advanced Flame 1.0
Advertisement
Table of Contents
Summary of Contents for Eastern Voltage Research Advanced Flame 1.0
- Page 1 Advanced Flame 1.0 Kit − 1 − November 2013, Rev 1 http://www.EasternVoltageResearch.com Advanced Flame 1.0...
- Page 2 Advanced Flame 1.0 Kit Introduction to the Advanced Flame 1.0 Kit Thank you for purchasing the Advanced Flame 1.0 Kit. This kit is a microprocessor controlled high power LED candle that offers several modes of operation including a variety of brightness levels, modulation levels, and effects. Whether you are looking to...
-
Page 3: Circuit Description
Please read this manual in its entirety before building, testing, or operating your kit! Circuit Description The Advanced Flame 1.0 utilizes a PIC12F683 microcontroller, U2, which produces a randomized output pulse width modulation (PWM) signal which is used to drive a high current MOSFET transistor, Q1, to power a CREE Piranha series LED, D1. -
Page 4: Kit Building Tips
Advanced Flame 1.0 Kit A pushbutton allows the user to cycle through the various operational modes and brightness levels. The presently selected mode is stored in non-volatile EEPROM (memory) location on the PIC12F683 so that if power is removed, the mode of operation is remembered the next time power is applied. - Page 5 Advanced Flame 1.0 Kit Surface Mount (SMT) Component Soldering Instructions One of the first things you’ll notice with your electronics kit is that many of the included components are surface mount components. These components do not have conventional leads, as is the case with thru-hole components, and instead solder directly to pads located either on the top or bottom of the PCB board.
- Page 6 Advanced Flame 1.0 Kit At first, surface mount soldering may seem a bit difficult, but its actually much easier than thru-hole soldering once you get the hang of it. Good luck and take your time! − 6 − November 2013, Rev 1 http://www.EasternVoltageResearch.com...
- Page 7 Advanced Flame 1.0 Kit Advanced Flame 1.0 Kit Parts List RESISTORS 10 ohm Resistor (brown-black-black), R1 47k Resistor (yellow-violet-orange), R2 82 ohm Resistor, 2W (grey-red-black), R3 CAPACITORS 0.33uF Capacitor, C1 0.1uF Capacitor, C2 DIODES 1N4148 Diode, CR1 LED, 4-DIP, D1 LED, T1 or T 1 ¾, D2 (optional supplied by end user)
- Page 8 Advanced Flame 1.0 Kit Advanced Flame 1.0 - Component Layout Diagram − 8 − November 2013, Rev 1 http://www.EasternVoltageResearch.com Advanced Flame 1.0...
- Page 9 Advanced Flame 1.0 Kit KIT Building Instructions Now we will begin building the kit. There are just a few more important things to know before we install the first components. For each component, the word “install” always means the following: Pick the correct value to start with.
-
Page 10: Set-Up And Testing
VIN on the PCB while the black wire connects to the terminal pad labeled GND. Congratulations! You have just completed your Advanced Flame 1.0 kit. Please take a few moments to look over the board and ensure that all the components are installed properly with the correct orientation. -
Page 11: Selecting Modes
Congratulations! Your Digital Flame 1.0 is now completed and operational. Selecting Modes Pressing the pushbutton once and releasing will advanced the Advanced Flame 1.0 to the next mode of operation. One mode is the OFF state. To turn OFF the Advanced Flame 1.0, either cycle the modes until the OFF mode is selected or remove the 9V battery or... -
Page 12: Terms And Conditions Of Sale
Eastern Voltage Research, LLC Technical Support support@easternvoltageresearch.com Thanks again from the people here at Eastern Voltage Research. Terms and Conditions of Sale Before opening or assemblying your kit, please read and review the latest Terms and Conditions of Sale on our website at the following link: http://www.easternvoltageresearch.com/terms.html...