Subscribe to Our Youtube Channel
Summary of Contents for SCHOTT Termofrost AGD3
- Page 1 ® ® SCHOTT SCHOTT Page 1 Termofrost Termofrost Installation manual SCHOTT Termofrost® Retrofit AGD3 / T.AGD3 Picture of installation, ideally taken from a real application...
-
Page 2: Table Of Contents
HEREIN BY THIS REFERENCE. THIS MANUAL IS PROVIDED “AS IS” WITHOUT ANY REPRESENTATIONS OR WARRANTIES, EXPRESS OR IMPLIED. IN NO EVENT SHALL SCHOTT BE LIABLE FOR ANY ECONOMIC LOSS OR LOSS OF PROFIT, OR INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES OR LOSSES OR DAMAGES ARISING OUT OF IMPROPER USAGE OR INSTALLATION OR ADJUSTMENT, NEGLECT, ACCIDENT OR FAILURE TO CLEAN AND MAINTAIN PRODUCT AS SET FORTH IN THE USER GUIDE AND/ OR TECHNICAL ADJUSTMENT INSTRUCTIONS, EVEN IF SCHOTT HAS BEEN EXPRESSLY ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. - Page 3 Handling of Schott Termofrost glass doors Take care when handling the Schott Termofrost doors. Do not place the glass doors on the floor without protection. When the door is placed on the floor, the gravity system on the bottom must not touch the ground to avoid the risk of damaging it.
-
Page 4: Recommended Tools And Accessories For The Installation
Rivets Alu Ø3x10 (6 rivets per line) Self drilling screws Ø4,8x30 (3 screws per system) Self drilling screws Ø3,9x15 (3 screws per system) Important Remark: Screws are not recommended by Schott but can be used in some particular cases! Riveter (electrical if possible!) Drilling machine... - Page 5 Alu Rivet Ø4,8x10 Alu Rivet Alu Rivet Ø4,8x10 Ø4,8x25 Fixation of the upper adapter to the console of the cabinet. Check the drawing provided by Schott Screws, nut and washer provided. Alu Rivet Ø4,8x10 Screw M6, nut and washer Alu Rivet Ø4,8x25...
- Page 6 M6 screw. Important Remark: Schott provides with all deliveries a sketch showing where the adapter is fixed to the cabinet ! Position the bottom adapters in level Distribute the gap between adapters and sidewalls identically on both side Tolerance +/- 1°...
-
Page 7: Installation
® ® SCHOTT SCHOTT Page 7 Termofrost Termofrost 5. Installation | Upper Adapter and frame Fix the upper adapter to the cabinet or to the L-console Use the frame as a measurement device for the correct height. Turn the L-shape in a way that... - Page 8 ® ® SCHOTT SCHOTT Page 8 Termofrost Termofrost 5. Installation | Doors of a line Hang in the doors - The bottom of the frame does not need to be fixed at this Door (in open position) has to be in stage 90°...
- Page 9 ® ® SCHOTT SCHOTT Page 9 Termofrost Termofrost 5. Installation | Adjusting the doors by sliding the frame on the bottom adapter It may be necessary to slide all lower profiles in one or in the other direction to be able to adjust the level of the doors.
- Page 10 The standard delivery consist of a PVC L-profiles (19x19x1mm) and/or a PVC plates (2000 x 100 x 2 mm). For special cases and bigger gaps on the sides Schott provides specific and...
-
Page 11: Controll Of Installation
All cabinets are properly cleaned after the installation and no metal span can be found inside or outside the cabinet All glass doors have been cleaned with a suitable glass clear (e.g. Nano Cleaner from Schott) Doors are closing automatically via the gravity system... -
Page 12: Care And Cleaning
® ® SCHOTT SCHOTT Page 12 Termofrost Termofrost 7. Care and cleaning Glass surfaces Surfaces may be cleaned with household glass cleaner and a sponge, tissue or paper towel. Cleaners containing alcohol may be used but the alcohol content should be no greater than 30%-40% of the solution. Remove any oily contamination with a grease cutting cleaner. - Page 13 ® ® SCHOTT SCHOTT Page 13 Termofrost Termofrost 8. Troubleshooting and problem solving Frame height in front openings changed due to installation Problem 1: door goes under the stop Problem 2: door scrapes to the vertical bar of the frame because of the bending...
- Page 14 ® ® SCHOTT SCHOTT Page 14 Termofrost Termofrost 8. Troubleshooting and problem solving Frame height in front openings changed due to installation Problem: door doesn't close Solution: shim inside outside Height is smaller than it should Solution: push the front of...
-
Page 15: Spare Parts
9.1 Spareparts for AGD3 door Spare parts needed for repair or maintenance operations can be obtained quickly and easily. Please feel free to contact SCHOTT Termofrost®, or your local dealer for a complete list of available spare parts. KIT DOOR AGD3/TAGD3 HINGE UPPER... - Page 16 ® ® SCHOTT SCHOTT Page 16 Termofrost Termofrost 10. Serial number and type for frame and doors Door label with type (article number for door) and Frame label with type (article number for frame) and Serialnumber (S/N) Serialnumber (No) On upper profile in left opening...
Need help?
Do you have a question about the Termofrost AGD3 and is the answer not in the manual?
Questions and answers