Advertisement
JA-120PC (90) PIR motion BUS detector with a 90° verification camera
Instant: During an alarm triggered by the detector, the camera can
be activated up to 3 times (then it will be auto-bypassed). Each activation,
depending on the detected movement and settings, takes 3 photos
maximum. Photos are sent to the control panel (9 photos maximum).
Delayed: The first activation (entrance delay) takes up to 2 photos
depending on the detected movement and saves them into the internal
memory (Send pre-alarm image disabled). When alarm is triggered, photos
are sent from the internal memory to the control panel. Then the behaviour
is the same as with an instant reaction (11 photos maximum).
Warning: When the Device autobypass / 3rd alarm is enabled (located
in Settings/Parameters) taking photos is blocked after the 3rd alarm. During
each alarm the detector can be triggered up to three times. This way,
the number of taken and transferred photos may be tripled (18/24 photos).
Applies to Instant / Delayed reactions.
Installation recommendations, cautions
Several JA-120PC (90) detectors can be installed in the system. However,
triggering several detectors at the same time will extend the transmission
time of photos to the control panel and MyJABLOTRON. Complete
transmission can take a few minutes.
In order to take a photo using a PG output, use the F-Link software and
set the Impulse parameter in the PG outputs / Function menu to a time
of at least 1 min. The PIR is limited to taking 1 requested photo by PG status
per minute.
The number of pre-alarm photos taken by a PG output is limited to 40
photos/day/control panel. The photo counter is reset at 00:00 hrs. Alarm
photos and photos requested in MyJABLOTRON have no limitation.
In the MyJABLOTRON Photo gallery / Sending notifications and during
maintenance mode by J-Link software all users have access to the photos
from all the system sections.
Installation in the corner of a room requires more attention during testing
due to possible reflections of the flash on the photographed scene
(especially in the dark).
Detection characteristics
The PIR detector has a 90°/12m coverage – see the picture below.
The detection characteristics of the PIR part has no influence on the camera
part of the detector. The lens cannot be changed for other types.
The camera has a viewing angle of 90°, the camera flash has a range
of 3 m.
Side wiew
Saving and browsing the photos
Every photo is taken twice: the first in low resolution (LQ = 320x240
pixels), the second in high resolution (HQ = 640x480 pixels).
All of the exposures are saved into independent folders Foto_LQ
and Foto_HQ on the Micro SD card. When the card's capacity is full,
the oldest photos will be replaced with new ones. Photos saved
on the micro SD card can be browsed in a photo browser on a PC.
Note: Some antivirus software may write its own data on the Micro SD
card. The detector will automatically format an SD card marked this way.
SD card formatting erases all data which has been saved. For more
information about formatting see Formatting the Micro SD card.
Photos are sent to the control panel in LQ. You can browse through these
images in F-Link and J-Link software, event memory by clicking
on an event called New image. Pictures are displayed in LQ, if you click
on Detail you can get second-exposure photos (HQ). Images can
be searched and browsed by a file manager or picture browser. In order
to display the photos this way it is necessary to start F-Link (J-link)
software, be logged into the control panel as a service technician
or
Administrator
and
then
Disc: Flexi_log /Foto. Here are all the photos which have been sent
to the control panel (LQ) and photos which have been requested
in Detail (HQ).
JA-120PC (90) BUS PIR motion BUS detector with a 90° verification camera
Top view
load
the
control
panel
memory.
Picture transmission to MyJABLOTRON
When the SIM card which is supplied by device distributor is used and
the customer uses MyJABLOTRON services, then the customer has direct
access to the photos from this service. Parameter settings of the transfer
of pictures are done during the panel registration. All the photos are
delivered and visible in MyJABLOTRON. Every single photo can be
requested in HQ resolution. There you can also choose telephone numbers
(for SMS) or e-mail addresses which will receive a message when a new
picture is taken. MyJABLOTRON can request a new picture without PG
output activation (see Installation recommendations, cautions).
MyJABLOTRON respects permissions of individual users concerning
photo verification accordingly to sections to which the users have access
(for example, a user from section 1 cannot browse through photos from
section 2)
WARNING: This detector allows you to take photos by PG output reaction
or from MyJABLOTRON even when the system is unset. The manufacturer
strictly warns the user that the detector has to be used within the limits given
by particular laws or norms, especially laws about the protection of personal
privacy.
The use of the detector is also subject to regulations on the protection
of personal data. The manufacturer recommends the users to familiarize
themselves with these regulations as well as with the regulations governing
the operation of CCTV before the use of the detector. Furthermore,
the manufacturer recommends the users to familiarize with General Terms
and Conditions of Cloud JABLOTRON and with Privacy Policy
(https://gdpr.jablotron.cz/).
According to these regulations users have an obligation to ensure
the approval of persons in range of the detector during the acquisition
of video recordings or the obligation to indicate the image capture area
by information tables.
Formatting the Micro SD card
The detector is supplied with a formatted Micro SD card (15). The yellow
indication LED (16) is turned off in normal detector mode. Slow LED flashing
indicates that the card was removed while data was being written on it,
or it has been changed for another SD card. The detector will work normally
with a new SD card only if the detector performs a card formatting.
Formatting the SD card is started by pressing the tamper contact (13).
The formatting procedure is indicated by quick flashing of the yellow LED
indicator (16). During this process all photos on the SD card will be erased,
however a backup of the photos is in the event memory log.
Technical specifications
Power
from the control panel BUS +12 V (+9 ... +15 V)
Current consumption
- nominal for the backup supply calculation
- maximum for cable choice
Recommended installation height
PIR detection angle/detection coverage:
Horizontal camera capture angle
Range of the flash
Camera resolution
Photo size LQ/HQ (typically)
Typical (LQ) photo transmission time to the control panel
Ideal (HQ) photo transmission time to the control panel
Typical photo transfer time to the server
Dimensions, weight
Classification
- according to
- operational temperature range
- operational environment
- certification body
Also complies with
JABLOTRON
ALARMS
the JA-120PC (90) is in a compliance with the relevant Union
harmonisation
legislation:
2011/65/EU. The original of the conformity assessment can
be found at
www.jablotron.com
Note: Although this product does not contain any harmful
materials we suggest you return the product to the dealer
or directly to the manufacturer after use.
2 / 2
5 mA
250 mA (with high flash intensity)
2.5 m above the floor
90°/12 m
max. 3 meters
LQ 320x240; HQ 640x480 pixels
2-20kB/2-64kB (6kB/5kB)
up to 20 s. (10 s)
up to 130 s (60 s)
15 s/GPRS; 2 s/LAN
110 x 60 x 55 mm, 102 g
Security grade 2/Environmental class II
EN 50131-1, EN 50131-2-2
-10 to +40 °C
indoor general
Trezor Test s.r.o. (no. 3025)
EN 50130-4, EN 55032
a.s.
hereby
declares
that
Directives
No:
2014/30/EU,
- Section Downloads.
MMP53103
90°
Advertisement
