Related Manuals for scandia TREND
Summary of Contents for scandia TREND
- Page 2 Trend Sauna Owners Manual and Installation Guide Insert Trend PICTURE here...
- Page 3 Please feel free to reach out to us with any questions or problems, and we will do our best to assist you. Thank you and God Bless EVERYONE! -Scandia Manufacturing Team - +1(877)467-2862...
- Page 4 Parts List You will receive the following inside your Trend Modular Sauna Kit. Overall Frame and System: 1. 2 x Upper Corner Piece 2. 2 x Lower Corner Piece 3. 2 x Wall Panel 4. 1 x Floor Panel 5. 1 x Ceiling Panel 6.
- Page 5 10. 2 x Door Hinges 11. 2 x Sauna Bench a. 2 x Sauna Bench Top b. 4 x Sauna Bench Legs 12. 1 x Heater Guard Rail 13. Fasteners a. Storefront Frame Front Screws (25) b. Storefront Frame Back Screws (30) c.
- Page 7 Step 1. Assemble the Frame Arrange the corner panels, wall panels, ceiling panel, and floor panel on the floor as shown below. The Slots in the ceiling panel should be up away from the floor. The upward face will be the back of the sauna. The dowels slide into the dowel holes. The ceiling panel has the slots in it, use small pieces of wood as spacers as you go so you can grip underneath, as this whole assembly will be lifted later on.
- Page 8 Between the Upper Corner Panels and the Ceiling panel are electronic connectors for the LED lights. As the pieces slide together go ahead and connect these. They are one way locking connectors. Carefully slide the pieces together until everything is connected. Use a mallet to tap the Frame Staples into place.
- Page 9 Step 3. BackPanels The Back Panels will be mounted next. The vent cutout goes on the bottom, away from the slots on the ceiling panel. The Back Panels will slide into place and then be fastened to the rest of the frame using the countersunk holes and Back Panel Screws. There is a wire for the LED lights coming out near the ceiling of the Back Left BackPanel.
- Page 10 Step 3. Lift The next step is lift the whole panel assembly off of its face into the standing position. This will take two to three people of average strength to do this safely. Take care during this process to not injure yourself or damage the sauna.
- Page 11 Step 4. LED Light Frosted Glass Panel The Frosted Glass Panels are held in place between two angle pieces of wood. The first is on the wall and is permanent, the second is on the ceiling and is screwed in place to allow for serviceability.
- Page 12 5. Heater The heater is mounted next. See the Scandia Ultra Sauna Heater Installation Guide for more information. Finalize the electrical connections and this part is done. Use 1 ¾” Wood screws to mount the heater to the wall to ensure you do not break through the back panel.
- Page 13 b. Loosely Mount the Storefront Frame Front Bottom, giving enough room that the storefronts can be inserted into the slot. Use the corresponding screws for this as well. c. Put the Right Storefront without Hinge into the appropriate slot. This piece is symmetrical, so either direction can be up.
- Page 14 e. Repeat the process with the Left Storefront with Hinge. This piece is not symmetrical, the hinge cutout that is 11.25” away from the edge of the glass will need to be top. Once you have it in place you can mount the Storefront Frame Front Side and Storefront Frame Front Top segments to secure the glass in place.
- Page 15 7. Door Use the supplied hinges to hang the door. Attach the hinges first to the door, ensuring you have the rubber grommet between so as not to scratch the door. There is a top and bottom of the door as well, with the hinge cutout being closer to the edge of the glass on the top of the door.
- Page 16 8. Benches and Heater Guard Rail a. Attach the legs to the bottoms of the benches using the pocket holes and supplied screws.
- Page 17 b. Place the benches and heater guard rail in place. Secure the benches into the walls through the outside rail using the accompanying fasteners. There is blocking in the walls to support this. Secure the heater guard rail to the back wall using the vertical posts.
- Page 18 9. Final Touches a. Heater Vent Covers just slide into place, put one on either side of the panel. b. Slide the wire cap cover into place on top of the sauna to cover the hole cutouts. Tuck the wires inside of the cover.
- Page 19 c. Attach the back wall split trim to hide the seam between the back wall panels. 10. Attach power to the bluetooth speaker from the electrical box, hook up your phone to the RGB Controller app, set the tone with some music and lights, and enjoy your sauna!
Need help?
Do you have a question about the TREND and is the answer not in the manual?
Questions and answers