Page 2
Pre-cut Value Gambrel - 4’ & 6’ Sidewalls AssEmbLy InsTruCTIOn mAnuAL *Please Note: a 4’ sidewall uNit was used for Pictures showN* Thank you for purchasing from Little Cottage Locate your rim boards and floor joist, layout as Company! If you have any questions during construction shown.
Page 3
Pre-cut Value Gambrel - 4’ & 6’ Sidewalls AssEmbLy InsTruCTIOn mAnuAL *Please Note: a 4’ sidewall uNit was used for Pictures showN* Using the WaLL LayOUT DIagRaM sheet. Locate the To create the interior wall, fasten the 2x4 studs with 3”...
Page 4
Pre-cut Value Gambrel - 4’ & 6’ Sidewalls AssEmbLy InsTruCTIOn mAnuAL *Please Note: a 4’ sidewall uNit was used for Pictures showN* Make sure the OSB top plate is flush on the Lay wall off to the side as shown.
Page 5
Pre-cut Value Gambrel - 4’ & 6’ Sidewalls AssEmbLy InsTruCTIOn mAnuAL *Please Note: a 4’ sidewall uNit was used for Pictures showN* Install the 7/16 OSB as shown. Making sure the OSB Lay wall off to the side as shown.
Page 6
Pre-cut Value Gambrel - 4’ & 6’ Sidewalls AssEmbLy InsTruCTIOn mAnuAL *Please Note: a 4’ sidewall uNit was used for Pictures showN* Temporarily install the piece of 7/16 x 3 1/2 x 20 OSB Fasten the truss to the temporary piece of OSB, with to to the top plate.
Page 7
Pre-cut Value Gambrel - 4’ & 6’ Sidewalls AssEmbLy InsTruCTIOn mAnuAL *Please Note: a 4’ sidewall uNit was used for Pictures showN* 3 1/2” Measure 3 1/2” out from the edge of the 2x4 plate Next layout 2x4’s, as shown for the door wall. See and secure with 2”...
Page 8
Pre-cut Value Gambrel - 4’ & 6’ Sidewalls AssEmbLy InsTruCTIOn mAnuAL *Please Note: a 4’ sidewall uNit was used for Pictures showN* Now locate the rafter. See the WaLL LayOUT DIagRaM Next place the truss as shown and fasten with 1 1/4”...
Page 9
Pre-cut Value Gambrel - 4’ & 6’ Sidewalls AssEmbLy InsTruCTIOn mAnuAL *Please Note: a 4’ sidewall uNit was used for Pictures showN* Next install Smartside siding. Make sure it is flush on Measure 3” from bottom of 2x4, as shown, and secure the inside and measures 3”...
Page 10
Pre-cut Value Gambrel - 4’ & 6’ Sidewalls AssEmbLy InsTruCTIOn mAnuAL *Please Note: a 4’ sidewall uNit was used for Pictures showN* Next install the door stops and keep flush with the Install the 2 3/4” trim around the door and secure top of the 2x4 (not Smartside) and secure with 2”...
Page 11
Pre-cut Value Gambrel - 4’ & 6’ Sidewalls AssEmbLy InsTruCTIOn mAnuAL *Please Note: a 4’ sidewall uNit was used for Pictures showN* Make sure the rakes are all installed and fastened Remove 2x4 brace. Top and bottom. with 3” nails.
Page 12
Pre-cut Value Gambrel - 4’ & 6’ Sidewalls AssEmbLy InsTruCTIOn mAnuAL *Please Note: a 4’ sidewall uNit was used for Pictures showN* Continue installing OSB gussets. See diagram for Pickup the truss, as shown, and flip it over, to attach more information.
Page 13
Pre-cut Value Gambrel - 4’ & 6’ Sidewalls AssEmbLy InsTruCTIOn mAnuAL *Please Note: a 4’ sidewall uNit was used for Pictures showN* Fasten opposite end same as last picture. Continue with walls. Next install gable wall. Make sure the walls fit nice and tight and fasten with 2”...
Page 14
Pre-cut Value Gambrel - 4’ & 6’ Sidewalls AssEmbLy InsTruCTIOn mAnuAL *Please Note: a 4’ sidewall uNit was used for Pictures showN* Fasten with 2” nails every 8”. Make sure you have 48” or 60” (depending on building width) in between the door opening, 48” on 8’...
Page 15
Pre-cut Value Gambrel - 4’ & 6’ Sidewalls AssEmbLy InsTruCTIOn mAnuAL *Please Note: a 4’ sidewall uNit was used for Pictures showN* Hang trusses on the walls. Install trusses, as shown, making sure they are 24” on center before fastening.
Page 16
Pre-cut Value Gambrel - 4’ & 6’ Sidewalls AssEmbLy InsTruCTIOn mAnuAL *Please Note: a 4’ sidewall uNit was used for Pictures showN* Secure with 2” nails as shown. Make sure the trusses are 24” on center before fastening. Now fasten the top outside corner.
Page 17
Pre-cut Value Gambrel - 4’ & 6’ Sidewalls AssEmbLy InsTruCTIOn mAnuAL *Please Note: a 4’ sidewall uNit was used for Pictures showN* Continue with sheeting. Continue with the sheeting. Next install aluminum corners and secure with 2” For door installation, you will be using three hinges, nails.
Page 18
Pre-cut Value Gambrel - 4’ & 6’ Sidewalls AssEmbLy InsTruCTIOn mAnuAL *Please Note: a 4’ sidewall uNit was used for Pictures showN* Then install the barrel bolt at the top of the door. Use your hammer to tap on the barrel bolt to locate the mark.
Page 19
Pre-cut Value Gambrel - 4’ & 6’ Sidewalls AssEmbLy InsTruCTIOn mAnuAL *Please Note: a 4’ sidewall uNit was used for Pictures showN* 102. 103. Continue with the latch. Next you are going to install the drip edge. This will be fastened with 3/4” nails.
Page 20
Pre-cut Value Gambrel - 4’ & 6’ Sidewalls AssEmbLy InsTruCTIOn mAnuAL *Please Note: a 4’ sidewall uNit was used for Pictures showN* 108. 109. Align the top of the starter shingles with the chalk Continue as shown. line and attach.
Page 21
Pre-cut Value Gambrel - 4’ & 6’ Sidewalls AssEmbLy InsTruCTIOn mAnuAL *Please Note: a 4’ sidewall uNit was used for Pictures showN* 114. Complete caps as shown. 115. Your finished product! (Shown above in the 4’ sidewall) Thank You For Purchasing From Little Cottage Co.