Advertisement
WARNING
!
• Study, understand, and follow all instructions
provided before use.
• Do not exceed rated capacity.
• Do not exceed maximum width.
• Never crawl under the suspended load for any
reason.
• Ensure that the engine is supported securely
before repairing.
• Do not use this device for any purpose other than
that for which it is intended.
• No alterations shall be made to this product.
• Failure to heed these markings may result in
personal injury and/or property damage.
OPERATION
1. Determine the location of the two engine support bolts
on your vehicle. Then place the Engine transverse
bar directly over these two bolts.
2. Adjust the boom extension (#2) to ensure that both
legs (#13 & 14) are sitting inside the fender of the
engine compartment.
If the inside fender lips are more than 61" apart
!
apart, the Engine Transverse Bar must not be
used. Do not exceed the designated marking (61").
Over-extending could cause the Engine Support Bar
to collapse, resulting in personal injury or property
damage.
3. Adjust to ensure the support arm (#10) is in correct
position. The rubber tip of the adjustable leg (#6)
should be on a flat, reinforced surface capable of
supporting the weight of engine. Tighten both wing
nuts (#4 & 8) to secure the adjustable leg (#6) and
support arm (#10).
4. Lower the threaded hooks (#3) to appropriate position.
Ensure that the hooks are directly over the engine
support bolts or brackets; therefore the engine does
not swing when vehicle is disassembled.
5. Attach
the looped ends of the two 1/8" braided
steel cables (#12) to the engine support bolts on
the engine and loop middle of braided cables over
hooks. If the engine being supported is equipped with
engine lift brackets, hook the hooks (#3) directly into
engine lift brackets for extra protection.
Note: Use only fasteners rated Grade 5 or higher as
engine support bolts.
6. Tighten the barrel hex. nuts (#7) on both hooks
until cables are snug or hex. nuts are tight against
support bar.
7. Double check that engine is properly supported
before disassemble the vehicle.
MAINTENANCE
Periodically inspect the Engine Transverse Bar. Ensure
all parts move freely. To help prevent rust, wipe clean
and/or blow dry after each use. If rust appears, sand
affected area and cover with suitable utility paint. Store
the Engine Transverse Bar in a clean, dry area.
REPLACEMENT PARTS
(Refer to Figure 2 & 3)
Not all components of the Engine Transverse Bar are
replacement items, but are illustrated as a convenient
reference of location and position in the assembly
sequence. When ordering parts, give part number
and description. Call or write for current pricing: SFA
Companies 10939 N. Pomona Ave. Kansas City, MO
64153, U.S.A. E-Mail: sales@omegalift.com
Tel: (888)332-6419 Fax: (816)891-6599
Omega Website: http://www.omegalift.com
Parts List
Item
Part No.
1
-
2
-
3
*
4
*
5
*
6
44700-6
7
*
8
*
9
*
10
-
11
-
12
44700-12
13
-
14
-
(*)
44700-15
16
-
17
-
-
44700-M0
-
44700-L0
-
44100-L0
(*) Hardware Kit includes item# 3, 4, 5, 7, 8 & 9
5
Description
Boom
Boom Extension
Threaded Hook
Wing Nut, M12
Hex. Bolt M12x120
Adjustable Leg
Barrel Hex. Nut
Wing Nut, M8
Hex. Bolt M8x65
Support Arm
Transfer Adapter
Braided Steel Cable, 1/8"
Leg, Boom
Leg, Boom Extension
Hardware Kit
Knob Screw
Rubber Block (44100)
Manual
Label for 44700
Label for 44100
Qty
1
1
2
1
1
1
2
1
1
1
1
2
1
1
-
1
-
-
-
-
Advertisement
