Related Manuals for VacuMaid UV100
Summary of Contents for VacuMaid UV100
- Page 1 For free technical support and installation or product questions, please contact us. 1-800-228-0285 Speak directly with the manufacturer. OWNERS MANUAL READ BEFORE OPERATING YOUR SYSTEM...
-
Page 2: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following: Read all instructions before using this appliance. WARNING: To reduce the risk of fire, electric shock or injury: Always follow these safety instructions •... -
Page 3: Grounding Instructions
CAUTION: Do not use when rug (or floor) is wet. ATTENTION: Ne pas utiliser lorsque le tapis (ou le plancher) est moduille. SAVE THESE INSTRUCTIONS * THIS IS NOT A WET VAC * -WARNING- ELECTRIC SHOCK COULD OCCUR IF USED ON WET SURFACES GROUNDING INSTRUCTIONS FOR CORD CONNECTED APPLIANCE This appliance must be grounded. - Page 4 PARTS Latches Intake Inlet stem attaches here. For use when adding additional wall valves. Cap inlet stem if not adding valves. Utility Valve Inlet Disposable Bag is located Use for “Vacuuming” inside the unit, below the lid. Low Voltage Wire Quick Clip Use if wanting to add DO NOT USE AS additional valves...
-
Page 5: Installation And Mounting
5. Tighten screws until the washers are snug against the rubber grommets. (Fig. 3) ATTACHING UNIT TO MOUNTING BRACKET Mount the VacuMaid® Utility Vac by sliding the attached unit bracket onto the wall bracket (Fig. 4) and slide it down until the unit rests securely into the bracket. - Page 6 Typical Installation Design of Utility Vac Hanger Bracket Suggested Guidelines 44” from floor to top hole of can bracket NOTE: * Power unit must be mounted at least 6 inches from sidewall & floor. Leave 44” minimum of 12” from ceiling or shelving.
-
Page 7: First Time Use
FIRST TIME USE Before using your system for the first time, follow these 4 steps. Protector plate must be installed properly for the 1 PROTECTOR PLATE vacuum to work Make sure the Protector Plate is in place. This is necessary for proper suction. Upon receiving your vacuum system, lift off the lid. -
Page 8: Using Your System
4 Install the HEPA bag onto the 2 inlet stems inside the canister. First, take the bag and fully expand it. Then place it in the canister and slide each gasket onto the inlet stems until they drop into place in the ridge that is around the inlet stems. -
Page 9: Maintenance
MAINTENANCE This system uses a sealed HEPA type bag (Part # HPB2HD). The mass of dirt and debris is picked up by your vacuum and deposited into the bag inside your dirt canister. Emptying your Dirt Can To remove accumulation, follow these steps: Remove the lid by unhooking the clamps &... -
Page 10: Year Limited Warranty
Refer to operating maintenance instructions Further, this Warranty does not apply to vacuum tubing, to ascertain that a malfunction of the vacuum fittings, inlets, or to the act of installing the VacuMaid® cleaner has actually occurred. UTILITY VAC system, including installation materials,... -
Page 11: Troubleshooting
Lift the lid. The metal plate should be located just beneath the HEPA bag inside the can, laying flat with the smooth side up, prong side down. Available at www.vacumaid.com ADDITIONAL KITS & ACCESSORIES or on Amazon. CKP30/CKP50 - 30 ft. or 50 ft. - Page 12 1-800-228-0285 Speak directly with the manufacturer. For replacement bags or to order additional tools or accessories, www.vacumaid.com visit us at or give us a call at 1-800-228-0285 To register your product online, go to www.vacumaid.com/registration...
Need help?
Do you have a question about the UV100 and is the answer not in the manual?
Questions and answers
How much water lift does it produce
The water lift produced by the VacuMaid UV100 is not provided in the given context.
This answer is automatically generated