Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for U-Reach Intelligent U3 Series
- Page 1 Intelligent U3 USB 3.1 Duplicator & Tester (USB/USB-HDD) User Manual vA.01...
-
Page 2: Table Of Contents
Index vA.01.3 Product Disclaimer ......................... 3 Warranty ..........................3 Piracy Statement ........................3 Before You Start ........................4 Notice Symbols ........................4 Introduction ..........................5 Function Table ......................... 6 Function Description ......................10 1. Copy ............................ 10 2. Compare ..........................11 3. -
Page 3: Product Disclaimer
U-Reach is not accountable for any incidental or consequential damages, which includes, but is not constrained to property harm, loss of time or data from use of a U-Reach product, or any other damages attributable to product malfunction or failure (including without... -
Page 4: Before You Start
Equal capacity of source and target is recommended for guaranteed data consistency. Using the Copy+Compare function provides the most flawless duplication. Damage incurred due to noncompliance with U-Reach operating instructions will void the warranty. Store the equipment safely when not in use and keep out of the reach of children. -
Page 5: Introduction
Introduction 1. Features The Intelligent U3 Series duplicator was designed with diversified media compatibility and high-speed performance in mind to not only flawlessly duplicate in high speed demands, but also provides helpful examinations by delivering the most accurate testing functions known today. -
Page 6: Function Table
Function Table *Below functions and features subject to change without notice. Function Description 1. Copy Data or whole media duplication only. Bit-for-bit comparison between the source and target flash 2. Compare medias. First copies, then compares the target to the source once 3. - Page 7 5.1. USB2 and USB3 Detects both USB2.0 and USB3.1 signals of the device. 5.2. Only USB3 5. Signal Detection Detects USB3.1 signal of the device. 5.3. Only USB2 Detects USB2.0 signal of the device. 6.1.1 USB Info. This feature will show flash’s data information, file format, content size, and capacity.
- Page 8 Copies the flash’s entire content, including the empty space. 7.2. Button Sound Enables or disables the audible beep when a button is pressed. Both USB 2.0/3.0 7.3 Active USB Revision Only USB 2.0 Select the USB Revision to active. Only USB 3.0 7.4 Target Tolerance No Limit Sets the capacity tolerance range between...
- Page 9 9.1 Copy+ Write Protect Copies data from the source to targets, then sets targets with write protection. 9.2 Copy+Comp+WriteP. Copies data from the source to targets then compares and set targets with write protection. 9. Write Protect 9.3 Set Write Protect Sets targets with write protection.
-
Page 10: Function Description
Function Description 1. Copy Step 1: Prepare source and target devices. Recommendation: Target device(s)’ capacity must be equal to or larger Note than the source device capacity. Step 2: Connect source and target devices. Step 3: Proceed to copy. Scroll to select "1. Copy", then press "OK" to start the duplication process. The number of working/connected targets will be displayed on LCD. -
Page 11: Compare
2. Compare The compare function checks the accuracy of copy result. Scroll to select "2. Compare", then press "OK" to start the verification process. 3. Copy+Compare Sequentially automates from Function 1, Copy to Function 2, then Compare. Scroll to select "3. Copy+Compare", then press "OK" to start the automated duplication and verification process. - Page 12 4.4 Signal+H5+Format This function can precheck the 2.0 / 3.0 signal of the flash’s first, then performs a read and write test to determine the flash’s quality. The flash’s original data will be erased during this test. The USB will be formatted into FAT32.. 4.5 H5+Format This function performs a read and write test to determine the flash’s quality.
-
Page 13: Signal Detection
4.10 Minimum Write Speed This function can be used to select the flash media whose writing speed is too slow. Users can set an expected minimum writing speed for media check, so the flash media that doesn’t reach the minimum speed value will be identified. When the red-light illuminates to indicate that an error has occurred, use Note the▲▼buttons to view the error information. -
Page 14: Utilities
6. Utilities 6.1 Information ➊ USB Info. This setting displays the flash media’s basic information such as file format, content size, and total capacity. Use the ▲▼buttons to view the information of each flash media, source included. [#01] 116G Total Capacity of the Device Data Size FAT32 Note... - Page 15 DoD Erase complies with the U.S.A. Department of Defense (DoD 5220) standards by erasing the flash three times, which guarantees that data is completely scrubbed. Note Use the▲▼buttons to view the status of each port during erase. 6.3 Do Format ➊...
-
Page 16: Setup
The firmware update process may take longer than 5 minutes. Please do not disrupt power or process during BIOS update. If interrupted, the Caution system will become useless. U-Reach will not be held responsible for any damages. 7. Setup 7.1 Copy Area... - Page 17 Also known as "Quick Copy”. The source’s format is automatically analyzed and if it’s recognizable, such as, FAT 16/32/64, NTFS, or Linux ext. 2/3/4, the system will copy the data only, rather than the entire flash. Copies 2GB data only [Copy Area] System and Files If the file format is not recognized, the whole flash card, including empty...
- Page 18 The duplicator will detect USB3.1 only. If the device does not support USB3.1 protocol, it will show “Fail.” 7.4 Target Tolerance This function sets the capacities tolerance range between the source and target flash. If the capacity is outside the tolerance range, the copy will fail. 100% Same No Limit Allow Tolerance...
-
Page 19: Log Manager
7.6 Power Off Time Between Copy+Compare The use of this setting is highly advised as it prevents data loss due to unstable flash. Users can set the time gap of power supply between copy and compare. The time gap can be set from 0 to 15 seconds. - Page 20 8.1 Out Today Report Insert flash media into Port 1. Go to "Out Today Report” and press “OK” to output today’s log records. Remove flash media and read the log report on PC. 8.2 Out Recent Report Insert flash media into Port 1. Go to "Out Recent Report"...
-
Page 21: Write Protect
*The PC-Link software (LV07B) is designed to continuously record log reports. If user executes “clear log records” on the duplicator while LV07 is still running, the conflict between LV07 and duplicator might lead a serious system error. Setup Password Setting a password ensures the duplicator’s log records are protected. During your first linkage, please wait for a few minutes on PC to complete create the log database from duplicator. - Page 22 If the sticks were originally protected, the system will automatically Caution release protection, then copy. 9.2 Copy+Comp+WriteP. Copies data from the source to targets, compares, then set the write protection on targets. If the sticks were originally protected, the system will automatically Caution release protection, then copy+compare.
-
Page 23: Specification
Specification Intelligent U3 USB 3.1 Duplicator & Tester Capacity Designed support capability over 18TB+ Stand-alone, FPGA-based operation (Non-PC Operation Type based) Specifications Supported Languages English or Japanese LCD Display Backlit Monochrome LCD Display LEDs 2 LED Indicators per Port (1 Red/ 1 Green) 4 Push Buttons (▲, ▼, OK, ESC) Control Panel Quick Copy (Systems &...