Related Manuals for Knight Agile Monitor Arms
Summary of Contents for Knight Agile Monitor Arms
- Page 1 Agile Monitor Arms Assembly Instructions Tools Included: Phillips Screwdriver, Allen Keys (2.5/4/5mm), Wrench knightgroup.co.nz...
- Page 2 Agile Monitor Arms Page 1 Assembly Instructions Single Monitor Arm Dual Monitor Arm Starts Page 2 Starts Page 10 IMPORTANT NOTES! Read the entire instruction manual before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, please contact your local distributor for assistance.
- Page 3 Agile Monitor Arms - Single Page 2 Page 2 Assembly Instructions Assembly Instructions Hardware Tools Components knightgroup.co.nz...
-
Page 4: Step 1 Mounting Option
Agile Monitor Arms - Single Page 3 Page 3 Assembly Instructions Assembly Instructions Step 1 Mounting Option Option A: Clamp A-2a A-2b knightgroup.co.nz... - Page 5 Agile Monitor Arms - Single Page 4 Page 4 Assembly Instructions Assembly Instructions Option B: Grommet Hole knightgroup.co.nz...
-
Page 6: Step 2 Installing The Arm
Agile Monitor Arms - Single Page 5 Page 5 Assembly Instructions Assembly Instructions Step 2 Installing the Arm 32” 2-9kg RATED knightgroup.co.nz... -
Page 7: Step 3 Connect The Monitor
Agile Monitor Arms - Single Page 6 Page 6 Assembly Instructions Assembly Instructions Step 3 Connect the Monitor Use a screwdriver (G) to screw the screws (C/D) into the four holes at the back of the monitor. Avoid over-tightening the screws as it may damaging the monitor. -
Page 8: Step 4 Tension Adjustment
Agile Monitor Arms - Single Page 7 Page 7 Assembly Instructions Assembly Instructions Step 4 Tension Adjustment If the arm sinks after mounting the monitor, use the allen key to adjust the screw on the arm. Turn counter- clockwise (‘+’ direction) to increase gas spring tension until it can hold the weight of your monitor. -
Page 9: Step 6 Cable Management
Agile Monitor Arms - Single Page 8 Page 8 Assembly Instructions Assembly Instructions Step 5 Leaning Adjustment If you feel the pitching angle is too tight or too loose when adjusting the mount, please adjust the screw shown. Step 6 Cable Management... -
Page 10: Step 7 Arm Adjustment
Agile Monitor Arms - Single Page 9 Page 9 Assembly Instructions Assembly Instructions As shown: 1 - Squeeze the arm buckle inward, with cable located in-between. 2 - Place arm buckle into the upper arm hole site. 3 - Insert cable into lower arm cavity and place the arm cover in position. - Page 11 Agile Monitor Arms - Dual Page 10 Page 10 Assembly Instructions Assembly Instructions Hardware Tools Components knightgroup.co.nz...
- Page 12 Agile Monitor Arms - Dual Page 11 Page 11 Assembly Instructions Assembly Instructions Step 1 Mounting Option Option A: Clamp A-2a A-2b knightgroup.co.nz...
- Page 13 Agile Monitor Arms - Dual Page 12 Page 12 Assembly Instructions Assembly Instructions Option B: Grommet Hole knightgroup.co.nz...
- Page 14 Agile Monitor Arms - Dual Page 13 Page 13 Assembly Instructions Assembly Instructions knightgroup.co.nz...
- Page 15 Agile Monitor Arms - Dual Page 14 Page 14 Assembly Instructions Assembly Instructions Step 2 Installing the Arm 32” 2-9kg PER ARM RATED knightgroup.co.nz...
- Page 16 Agile Monitor Arms - Dual Page 15 Page 15 Assembly Instructions Assembly Instructions Step 3 Connect the Monitor Use a screwdriver (G) to screw the screws (C/D) into the four holes at the back of the monitor. Avoid over-tightening the screws as it may damaging the monitor.
- Page 17 Agile Monitor Arms - Dual Page 16 Page 16 Assembly Instructions Assembly Instructions Step 4 Tension Adjustment If the arm sinks after mounting the monitor, use the allen key to adjust the screw on the arm. Turn counter- clockwise (‘+’ direction) to increase gas spring tension until it can hold the weight of your monitor.
- Page 18 Agile Monitor Arms - Dual Page 17 Page 17 Assembly Instructions Assembly Instructions Step 5 Leaning Adjustment If you feel the pitching angle is too tight or too loose when adjusting the mount, please adjust the screw shown. Step 6 Cable Management...
- Page 19 Agile Monitor Arms - Dual Page 18 Page 18 Assembly Instructions Assembly Instructions As shown: 1 - Squeeze the arm buckle inward, with cable located in-between. 2 - Place arm buckle into the upper arm hole site. 3 - Insert cable into lower arm cavity and place the arm cover in position.
Need help?
Do you have a question about the Agile Monitor Arms and is the answer not in the manual?
Questions and answers