Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Aurora I-TV 110
- Page 1 Aurora I-TV All-in-One LED Display Terminal P r o d u c t M a n u a l...
-
Page 2: Table Of Contents
CONTENTS Ⅰ. Product Introduction............5.4 Computer Screen Share............1.1 Product Brief..............5.5 Mobile Phone Screen Share..........5.6 Multi Terminals Simultaneous Screen Share......1.2 Product Features............1.3 Product Appearance............. 5.7 External Device HDMI Display..........1.4 Specifications..............5.8 Playback via USB..............Ⅱ. Product Installation and Wring..........Ⅵ. - Page 3 This manual systematically introduces the product components, ports, specifications and other product contents, as well as installation, function applications and other instructions, aiming at guiding you to start an efficient experience with Aurora I-TV This manual takes the Product 138" as an example to make the introduction, and the installation, maintenance and operation methods are applicable to Product 110”, 138”, 165”...
- Page 4 WARNING This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. NOTE It is highly probable that you will not be able to get the best display effect if you ignore the content of the notice. 1) Wear anti-static gloves and anti-static bracelet during installation and maintenance;...
-
Page 5: Ⅰ. Product Introduction
Ⅰ. Product Introduction 1.1 Product Brief 1.2 Product Features 1) The product adopts integrated design and internal I-TV is Aurora's integrated commercial LED display terminal product. It has built-in control system, supports HDMI integrated system, which can be used without external equipment;... -
Page 6: Product Appearance
1.3 Product Appearance 1.4 Specifications SPECIFICATION I-TV 110" I-TV 138" I-TV 165" I-TV 220" Size 110" 138" 165" 220" Pixel Pitch(mm) Brightness(nit) 100~500 100~600 Refresh Rate(Hz) 1920~3840 Resolution 1920×1080 Power Consumption 2500/850 3000/1020 3060/1040 5120/1740 (Max/Ave) (W/display) Display Area(mm) 2440×1373 3050×1716... -
Page 7: Ⅱ. Product Installation And Wring
Ⅱ. Product Installation and Wring 2.1 Open-package Inspection Product Package Name Outer Packing Inner Packing Module 1 wooden case 5 cartons 216 modules Cabinet 1 wooden tray 13 cartons 25 cabinets 1 set of bottom frame component 1 set of foot-mounting brackets left and right upper rims Installation Components 1 wooden case wall-mounting strip/hook plate... -
Page 8: Installation Environment Requirements
Overall Effect Diagram our company; if you use non-I-TV standard Aurora supporting kits, our company shall not assume any responsibility for damage to other items. - Page 9 Step 2: Wall-mounting strip installation ① Match corresponding components for wall-mounting strip assembly, as shown below: wall-mounting strip 1 wall-mounting strip 2 M5*20 slotted grub screws ② Tighten the mounting screws with the appropriate tools and connection plate the brackets are assembled, as shown below:assembly parts, as M5*16 countersunk screw shown below: ② Attach the wall-mounting strip to the bracket as shown below:...
- Page 10 ③ The wall-mounting strips and bracket are assembled, as shown below: ③ Install the hooks on the corresponding cabinets with two M8*25 hex head bolts and flat spring washers, as shown below: ④ The positioning pins shall be removed from the top cabinet. And the spring positioning pins shall be removed from the leftmost columns, and then fix the upper cover strip with a cross screwdriver, as shown below:...
- Page 11 ③ Complete the other column cabinet installations in sequence, Step 4: Display assembly as shown below: * Ensure the bracket casters are locked and the wall-mounting strips are horizontal before mounting the cabinet on the supporting structure; ① Hang the cabinets from the middle to the sides, and hang the wall-mounting strip on the cabinet to the wall-mounting strip of the bracket;...
- Page 12 Step 5: Bottom frame assembly ② Wiring: Red one is the 5 branch power line, blue one is the * The lower frame component consists of the lower frame 1, 2, etc., signal line. First connect the power and signal lines between the and shall be connected by the connecting plate cabinets according to the schematic.
- Page 13 ③ Button board connection: The power cable (3p paired plug) and Step 6: Module installation * Module installation sequence should be from left to right, right to left cable (7p, 4p, 3p) on the button board must be docked on site. Power cable (the black ones in below picture is required to be inserted in or from bottom to top, top to bottom, depending on the on-site pair), the cable can be inserted as 7p to 7p (red ones), 3p to 3p...
- Page 14 Step 7: The left, right, top and bottom cover plate Installation ① The left and right cover strips are snapped into the side spring locating pin holes. (as mentioned that spring locating pin and the cover strip shall be removed from the left side of the screen), as shown below: left cover strip buckle right cover strip buckle...
-
Page 15: Ⅲ. Functions Introduction
Ⅲ. Functions Introduction 3.1 Hardware Ports Instruction Port No. Name Function Red/Blue Indicator Red: standby status light Blue: work status Infrared indicator Receive remote control signals One-button Control one-button on/off switch switching button Signal switching Switching button for Android main interface, wireless screen button interface and HDMI input device interface. -
Page 16: Ⅳ. Remote Control Button Instruction
Ⅳ. Remote Control Button Instruction Remarks: Button Icon Function Channel switching function: Android main Standby/Awake interface - wireless screen transmission interface - external HDMI display channel interface switching Down in order; Left Brightness adjustment function: The brightness Right of the all-in-one LED display is designed in 8 levels, Confirm and can be adjusted by left and right buttons on the Volume+... -
Page 17: Ⅴ. Instructions For Use
Ⅴ. Instructions for Use 5.1 Start up 5.1.1 Plug in the power supply; 5.1.2 Press the one-button start up button on the bottom of the control unit to wait for a few seconds and then the display will automatically enter the main interface. (Note: After the first installation is completed, it takes 5-10 minutes for the display to automatically load the data, and it will light up when the loading is completed.) -
Page 18: Wireless Screen Share Function Instruction
5.3 Wireless Screen Share Function Instruction Wireless screen share function MAC or Windows system computer, mobile phone, tablet device can realize screen share function on the all-in-one display, and following are three methods to enter the interface: Method 1: Click the signal switching button of the remote controller;... -
Page 19: Computer Screen Share
5.4 Computer Screen Share 5.4.2 Windows System Device Wireless Scree Share ① Download and install the screen assistant application 5.4.1 MAC System Device Wireless Scree Share software; ① Connect the all-in-one LED display Wi-Fi hotspot; ② Connect the all-in-one LED display Wi-Fi hotspot; (Name: AndroidAP Password: 12345678) (Name: AndroidAP Password: 12345678) ② Follow the instructions and video demonstration in the MAC... -
Page 20: Mobile Phone Screen Share
5.5 Mobile Phone Screen Share ② Open the Screen Assistant and start to share screen, as shown below: 5.5.1 Android system mobile phone: Connect the all-in-one LED display Wi-Fi hotspot; (Name: AndroidAP Password: 12345678) ① Scan the following QR code to download the mobile app screen assistant;... -
Page 21: Multi Terminals Simultaneous Screen Share
5.6 Multi Terminals Simultaneous Screen Share 5.5.2 IOS system mobile phone: Pull out the menu from the bottom of the phone, click on the Screen Mirroring to select Android AP, and start to screen First, one terminal (such as a mobile phone, a tablet, or a computer) mirroring, as shown below: completes the screen share operation, and another terminal (computer) shall be inserted into the wireless screen transmitter and... -
Page 22: Ⅵ. Common Troubleshooting And Parts Replacement
Ⅵ. Common Troubleshooting and Parts Replacement ② Check if the display on/off switch is turned on. 6.1 Common Troubleshooting 6.1.4 No image display after connecting to the computer with HDMI cable 6.1.1 Partial black screen on boot ① Check if it is currently in the HDMI channel; ① Check if the network cable inside the cabinet is in poor ② Check if the HDMI cable on the whole unit and the external contact. -
Page 23: Parts Replacement
6.2 Parts Replacement 6.2.1Module Replacement Steps Diagram Method Find the specific location of the fault module and place the front maintenance Step 1 tool in the center of the module up to 3cm. Rotate the handle of front maintenance tool to absorb the module, and take out Step 2 the module in parallel. - Page 24 6.2.2 Hub Board Replacement Steps Diagram Method Find the location of the fault cabinet, Step 1 remove all modules, and unplug the signal line. Step 2 Unplug the power cord. Step 3 Remove 9 screws on the hub board. Take out the hub board. Step 4...
-
Page 25: Ⅶ. Packaging, Storage And Transportation
10%~85% RH. It is forbidden 8.2.1 Description of warranty service content to place the unit cabinet in the environment of volatile, corrosive Aurora provides high-quality after-sales service for and flammable chemicals. I-TV integrated LED display terminal with 2 years warranty. -
Page 26: Ⅸ. Special Statement
Aurora. 9.2 The contents of this manual are for reference only and do not constitute a commitment of any kind. 9.3 Aurora reserves the right to make improvements and changes to the product design without prior notice.
Need help?
Do you have a question about the I-TV 110 and is the answer not in the manual?
Questions and answers