Summary of Contents for Riverstone Networks Mojave Edition 041315V
- Page 1 Mojave Edition Made in the USA Monticello Solar Ventilation System Assembly Instructions 041315V WA RRAN TY 65 Fleetwood Drive, Rockaway, NJ 07866 Customer Service: (877) 373-3078 Email: customerservice@rsiww.com After Hours Helpline: (443) 574-4764...
- Page 2 Thank you for choosing the Monticello Greenhouse Program Thank You for your Purchase We want to thank you for your purchase of the Monticello Greenhouse. We appreciate your support of our American Made Greenhouses. The Monticello is designed for the average homeowner; no special degrees are needed. The time to assemble depends on the weather, skills, options, and number of helpers you have in the process.
-
Page 3: List Of Parts
List of Parts WARNING: Profiles with cut edges and/or drilled holes are sharp. Use extreme caution when handling. The greenhouse is shipped in multiple cartons. These cartons are heavy. Use care when lifting them. Some parts have sharp edges. Use extreme caution when handling. Wear proper safety gear including work shoes, gloves and safety goggles. - Page 4 1.1A Place F-10 profile on 1.1B Secure B-2 with three T-bolt W-7 panel. Make sure assemblies and one S-2C cap profile fits snugly as shown. between F-8 back profile and F-1 wall profile. F-10 1.1c Place another F-10 1.1D Fit W-9 panel into channel in F-10 Profile about 5”...
- Page 5 The two sets of F-6 and F-10 profiles fit on top of W-1 panels. Line up bottom bolt channels with top edge of F-1 and F-7 vertical profiles. Profiles will fit snugly. 1.2A Working from inside right corner, place F-6 profile with mitered end next to corner and angled edge facing up onto corner W-1 panel.
- Page 6 Install Fan and Solar Panel Make certain the pieces are in the correct positions before securing. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. 2.1A Working from inside, fit H-8 fan over S-11 bolts in F-10 profiles.
- Page 7 2.3B Working from outside insert 2.3A Working on the ground, line four T-bolt assemblies into up holes in H-1 brackets with slots on H-1 brackets. holes in H-6 shutter. Secure Secure to F-8 and F-1 with S-7 bolts and S-2 caps. profiles as shown.
- Page 8 2.4A Working from outside, fit H-4 brackets ontoT-bolts on F-8 and F-1 profiles. Secure with S-2C caps. S-2C NOTE: VIEWS FROM OUTSIDE. 2.4B Place H-3 profile on H-4 brackets. Fit H-5 connector underneath and secure with S-11 bolts, S-5D washers and S-2D nuts as shown. 2.4c Install 4 S-5A connectors on to...
- Page 9 2.5A Working from inside. Drill hole through polycarbonate. NOTE: VIEW FROM INSIDE. 2.5B Connect wires to Solar Panel. Push the wires to the inside of the greenhouse (leaving enough wire on the outside to connect). NOTE: VIEW FROM OUTSIDE. 2.5c Measure over to the thermostat This wire This wire to...
- Page 10 2.5D Continue the wire over to the fan and attach to the wires of the fan with the two wire nuts provided. If it runs backwards reverse wires. NOTE: VIEW FROM INSIDE. OPTIONAL CHARGE CONTROLLER AND BATTERY: For accurate wiring 2.5E using charge controller and battery, refer to the wiring diagram provided with the charge controller.
Need help?
Do you have a question about the Mojave Edition 041315V and is the answer not in the manual?
Questions and answers