Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Long Island Technology Group BFW Dover
Summary of Contents for Long Island Technology Group BFW Dover
- Page 1 Dover LED Headlight Operating Manual...
-
Page 3: Table Of Contents
Table of Content Symbol Description ..................2 Warnings and Cautions ................3 Intended Use ....................... 4 Unintended Uses ......................4 Overview .....................5 Assembly and Operation ................6 Headlight Assembly ..................... 6 Controller ........................9 Battery ........................10 Charging the Battery ....................11 Linkage Assembly ...................... 12 Removing the Headlight .................... -
Page 4: Symbol Description
Symbol Description These important symbols may appear on your Long Island Technology Group Optic Headlight. Please note their meaning. Attention: Read this owner’s manual for all warnings, precautions and instructions for use. CE marking of conformity indicates this device complies with European Directive 93/42 EC on medical devices and Directive 2002/95/EC on the restriction of the use of certain hazard- ous substances in electrical and electronic equipment. -
Page 5: Warnings And Cautions
Use Headlight only with Long Island Technology Group accessories, power supplies, batteries, and con- trollers. DO NOT modify this equipment Service must be performed only by Long Island Technology Group or properly trained biomedical tech- nician Avoid prolonged contact with the headlight during use as it may be hot USE ONLY components and accessories listed on page 5 and 18 of this manual. -
Page 6: Intended Use
Warnings and Cautions Intended Use The Dover™ is an ultra-portable medical light source. The device is intended to be mounted on a head- band or to the glasses frame of the doctor’s loupes or eye wear. The light is an excellent supplementary light source for examinations and procedures. -
Page 7: Overview
Overview Headlight Headband (accessory) Glasses Clip (accessory) Holster w/ Battery Battery Charger (Regular Shown) Charger Power Supply... -
Page 8: Assembly And Operation
Assembly and Operation Headlight Assembly NOTE. Your headlight may come pre-installed on the headband or the glasses clip depending on how you or- dered it. If your headlight came pre-installed on a headband you may skip to page 7. 1. Attach optic (A) to glasses through use of glasses clip (B) if using glasses. 2. - Page 9 Assembly and Operation...
- Page 10 Assembly and Operation 3. Place the battery (D) in the holster (E). Battery Battery Holster Only use Long Island Technology Group batteries. Replacement of batteries by untrained personnel could result in dangerous conditions such as fire or explosion...
-
Page 11: Controller
Assembly and Operation Controller 1. Connect headlight cable to holster connector (C), secure treaded cap tightly. 2. Attach the controller to waistband with the controller clip (B). 3. To turn the light on push either of the Side Buttons (A). 4. -
Page 12: Battery
Assembly and Operation Battery 1. Remove battery by pulling the Retaining Tab (A) or pushing the battery though the access hatch (B) on the back of the holster. Retaining Tab Access Hatch 2. To check the battery level press the Battery Fuel Gauge Button (D) on the front of the battery (Four green bars on the Battery Fuel Gauge (C) indicate a full charge). -
Page 13: Charging The Battery
Assembly and Operation Charging the Battery Your BFW Dover will come with one of two versions of battery chargers shown below. Regular on the left and Mini on the right. Charging Indicator (See Table Below)* Charging Indicator* Green Blinking Battery is currently being charged Green Solid Battery is fully charged Red Blinking... -
Page 14: Linkage Assembly
Assembly and Operation Linkage Assembly Headband (Classic Shown) Headlight Bolt Barrel Washer X 2 Flathead Screwdriver Allen Wrench Set Screw DO NOT use Thread Locking Glue On the Linkage. Can Cause Irreparable Damage to Linkage Leading to a Hazardous Situations... -
Page 15: Removing The Headlight
Assembly and Operation Removing the Headlight 1. Use the Allen wrench and Phillips head screwdriver to unlock the binding post. 2. Use the flathead screwdriver and Phillips head screwdriver to unscrew the binding post. -
Page 16: Mounting The Headlight
Assembly and Operation Mounting the Headlight 3. Place a washer on both sides of the linkage with the concave side towards the linkage. 4. Place the linkage with washers between the fork bar. - Page 17 Assembly and Operation 5. Place the barrel through the left side of the fork bar. 6. Thread the bolt into the right side of the fork bar and tighten the binding post with the flathead and Phil- lips screwdriver.
- Page 18 Assembly and Operation 7. Place the set screw inside the barrel and tighten it using the Allen wrench and Phillips screwdriver.
-
Page 19: Cleaning And Maintenance
Cleaning and Maintenance Headlight 1. Clean the Dover components with an alcohol wipe. 2. Only use a lens cloth or lens paper on the surface of the optic lens. 3. Use a can of compressed air to clean out any dust accumulations. DO NOT pour cleaning solution directly on the surface of the Dover DO NOT use any sterilization process or cleaning process using excessive heat or humidity as it will damage the device. -
Page 20: Specifications
Specifications Classification Classification & Type Class I: Medical Accessory, General Medical Equip- ment as to fire and mechanical hazards Environment Operation 60 Degrees F (15 C) to 80 Degrees F (26.7 C) Storage 32 Degrees F (0 C) to 104 Degrees F (40 C) Relative Humidity 45% - 75% Pressure/Altitude... -
Page 21: Electromagnetic Compatibility
Electromagnetic Compatibility Portable and mobile RF communications equipment can affect medical electrical equipment Guidance and manufacturer’s declaration-electromagnetic emissions The Dover is intended for use in the electromagnetic environment specified below. The customer or the user of the Dover should assure that it is used in such an environment Immunity IEC 60601 Test Compliance Level... - Page 22 Electromagnetic Compatibility NOTE 1: At 80 MHz, the separation distance for the higher frequency range applies. NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from surfaces, objects, and people. (1) Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, am- ateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy to asses the electromag- netic environment due to fixed RF transmitters, an electromagnetic site survey should be considered.
- Page 23 Electromagnetic Compatibility Guidance and manufacturer’s declaration - electromagnetic immunity The Dover is intended for use in the electromagnetic environment specified below. The customer or the end user of the Dover should assure that it is used in such an environment. Immunity test IEC 60601 test level Compliance level...
- Page 24 Electromagnetic Compatibility Guidance and manufacturer’s declaration - Electromagnetic Emissions The Dover is intended for use in the electromagnetic environment specified below. The customer or the end user of the Dover should assure that it is used in such an environment. Emissions Test IEC 60601 test level Compliance level...
-
Page 25: Troubleshooting And Service
• Servicing by unauthorized persons • Use with unauthorized accessories In all cases Long Island Technology Group, reserves the right to determine the cause of all malfunctions and at its sole discretion will determine the damage and/or repairs that are covered under this warranty. - Page 26 IEC 60601-1 Edition 4, IEC 60601-1-2 Edition 3 60 Carolyn Blvd, Farmingdale NY 11735 AAMI ES60601-1 Edition 1, CSA C22.2 NO 60601-1:08 Edition 2 (631) 270-4463 litgp.com Manufactured by Long Island Technology Group, LLC Revision 4.4 9/30/2019 60 Carolyn Blvd, Farmingdale, NY 11735...