Nero Radio 8117 micro Quick Start Manual

1. Designation
The radio card Radio 8117 micro is designated to control the automation
units of sliding, swinging, sectional doors and barriers.
2. Specifications
Supply voltage range AC/DC, V............................................................................................................................~9-24/=12-30
Consumed current, mA ...................................................................................................................................................NMT 100
Maximum permissible switching current, A...............................................................................................................5 (at cos=1)
Number ochannels.........................................................................................................................................................................2
Command duration (for each channel), s..................................................................................................................................1,5
Operating frequency range, MHZ....................................................
Number of recorded remote control codes .............................................................................................................................500
Overall dimensions,mm.................................................................................................................................................98×32×22
Operating temperature range, °C........................................................................................................................from -30 to +50
Connector wires section.....................................................................................................................................................0,5 mm
Degree of case protection ......................................................................................................................................................IP55
The product is not intended to be installed and operated in explosive and fire hazardous areas and does not require
protective grounding.
3. Special features
- supporting a new improved dynamic radio protocol with high range and noise immunity;
- 2 channels to control other manufacturers automation;
- control using the Radío series remote controls;
- supporting remote controls with feedback (see remote control instructions);
- retransmission the dynamic code of the Radio series remotes.
4. Connection
Connecting wires and cables with polyethylene insulation or sheath are not allowed.
It is not allowed to install the device at a distance of less than 1 m from heating appliances.
The holes in the cable glands must be made with a tool of a smaller diameter than the inserted cable.
Power supply
~ 9–24 В
= 12–30 В
Programming button
(light indicator)
Antenna
5. Remote control programming
Action
1. Enter the device into remote control programming mode (remote control PM)
Press and hold the Programming button for more than 4 s.
2. Select a channel for remote control record
Press and hold the Programming button for more than 1 s (channels change
circle-wise).
3. Record remote control channel to the device memory
One channel of the remote control can be recorded in only one of the two channels of the device, i.e., two
channels cannot be recorded in one channel of the remote control.
Since 2019, most remote controls are available with a dynamic code as the factory setting. See the instructions
for the remote control for details.
Radio a) in dynamic mode: press the remote control button and hold
8101-1M it for more than 2 s;
b) in static mode: press briefly the remote control button
(less than 1 s).
Radio a) in dynamic mode: press the recordable remote control
button and, while holding it, briefly press any other one;
8101-2M
b) in static mode: press briefly the recordable button.
8101-4M
Radio a) in dynamic mode:
1) select a recordable channel;
8101-5
2) record the channel: press the «STOP» button and,
8101-15
without releasing it, briefly press the «UP» button, then
release both buttons.
b) in static mode:
1) select a recordable channel;
2) press briefly the «STOP» button.
c) in dynamic mode with feedback:
1) select a recordable channel;
2) record the channel:
-press simultaneously the «STOP» and «UP» buttons;
-release the UP button, without releasing «STOP»
- receive the remote control signal about successful
recording to the device (for more details, see the
instructions for the remote).
Radio card
Radio 8117 micro
Рassport
.................................................................. 433,05 434,79
General/com
Channel 2
Channel 1
com
4
Figure 1 — Radio card connection
Indication
Indicator lamp is red.
The number of red blinking
1 – 1st channel;
2 – 2nd channel.
During recording, the device indicator
light flashes green short-long-short.
If the remote control is already
recorded, the indicator flashes green
briefly.
If the memory is full, the indicator
flashes yellow for 3 s.
Remote control indication in dynamic
mode with feedback:
- the channel is recorded: 1 beep l and
1 diode blink for the recorded channel;
- the channel is not recorded: 3 beeps
and 3 diode blinks for the recorded
channel (see the instructions for the
remote control).
3. Delete remote control channel from device memory (remote control PM)
Radio a) in dynamic mode:
8101-1M 1) enter the remote control into programming mode: press
the button 3 times in a row, and for the fourth one - hold
the button for 4 s. The pressing interval should not exceed
1 s;
2) remove the remote control: press the remote control
button and hold it for more than 1 s.
b) in static mode: press the remote control button and hold it
for more than 1 s.
Radio a) in dynamic mode: press the button of the deleted channel
and, holding it, press any other and hold it for more than 1 s,
8101-2M
then release both buttons;
8101-4M
b) in static mode: press and hold the button of the deleted
channel for more than 1 s.
.. -
Radio a) in dynamic mode:
1) select the deleted channel;
8101-5
2) record the channel, press the «STOP» button and
2
8101-15
without releasing press briefly the «DOWN» button, release
both buttons.
b) in dynamic mode:
1) select the deleted channel;
2) press briefly the «STOP» button.
c) in dynamic mode with feedback:
1) select the deleted channel;
2) record the channel,
-press simultaneously the «STOP» and «DOWN» buttons;
-release the «DOWN» button without releasing the «STOP»
button (to receive the remote control signal about
successful removal from the device, see the instructions for
the remote control for more details).
4. Delete channels of all remote controls from the device memory (remote controls PM)
Press and hold the Programming button for more than 8 s.
5. Remove the device from the programming mode of the remote controls
Press briefly the Programming button.
In case of inactivity, the device will automatically exit programming mode after 32 s
6. Mode of operation
The device can operate in one of three modes.
Single-channel mode (command duration is 1.5 s) is used to control a single object. For example, a barrier: 1st channel
is responsible for the UP direction, and the second – DOWN direction. In this case, control is performed by all remote
controls recorded in both channels of the device (see Figure 2).
Two-channel mode (factory setting). Command duration is 1.5 s. It is used to control two automation objects. However,
it should be taken into account that the radio card has one common input (3 "com" terminal), and it is not possible to
connect it to different potentials at the same time (see Figure 3)
Barrier/door
control unit
Continuous command mode (command duration is infinite). It is used to control automation objects in which a
continuous command is required, for example, a command to block the doors or gates automation. However, it should be
taken into account that the radio card has one common input (3 "com" terminal), and it is not possible to connect it to
different potentials at the same time (see Figure 4).
Action
Сh
4
1
Figure 2 — Single-channel mode
Сh
4
1
Figure 3 — Two-channel mode
1
Sliding door
control unit
lock
P
Figure 4 — Continuous command mode
Indication
In PM, the remote control light
indicator flashes red.
Upon removal, the device light
indicator will flash for a long time and
continue to flash in red.
The device light indicator will flash for
a long time and continue to flash.
Remote control indication in dynamic
mode with feedback:
-channel deleted: 2 beeps and 2
diode blinks for the deleted channel;
-channel has not been deleted: 3
beeps and 3 diode blinks of the
deleted channel (see instructions for
the remote control) in red.
The light indicator flashes red twice
for a long time.
Light indication stops.
Barrier/door
control unit
Сh
4
1