Subscribe to Our Youtube Channel
Related Manuals for DMS FR Series
Summary of Contents for DMS FR Series
- Page 1 " " " " "FR" MODEL SERIES Generic Email Version 1155 Rose Road Lake Zurich, IL 60047 USA...
- Page 2 Corporate Headquarters DMS, Incorporated 1155 Rose Road Lake Zurich, IL 60047 Phone: 847-726-2828 Fax: 847-726-9292 Toll Free Sales and Technical Support 800-655-7882 Foil Hot Stamp Unit Information Hot Stamp Unit Model Number FRXXXYYY Hot Stamp Unit Serial Number Generic Foil Printing Controller Model Number...
-
Page 3: Table Of Contents
Contents Introduction…………………………………………………………………………………………3 Unpacking and Inspection…………………………………………………………………………..4 III. Press Preparation……………………………………………………………………………………5 System Assembly………………………….………………………………………………………..6 System Startup and Adjustments………………………………………………………………...…8 System Maintenance………………………………………………………………………………11 VII. Notes………………………………………………………………………………………………12 Appendix A: Illustrated Parts List…………………………………………………………………….……14 Appendix B: Hot Stamping Tips & Tricks…………………………………………………………………18 Appendix B: MSDS-Material Safety Data Sheet..…………………………………………………………21... -
Page 4: Introduction
Section I: Introduction Thank you for choosing the foil printing system by DMS, Incorporated. The system described in this manual is the result of thousands of combined man-hours of practical experience, along with extensive research and development in foil printing applications. -
Page 5: Unpacking And Inspection
It is a good practice to keep the cartons and crates that the system is shipped in to reuse them if the system ever needs to be returned for service. Please notify DMS upon arrival if there are any possible omissions or damage to the system during... -
Page 6: Press Preparation
Section III: Press Preparation In order to automatically raise the base roll when the press runs, the HP-3002 temperature control unit needs to be supplied with a source of power when the press is in “RUN” mode only. This source of power is referred to as the slave line. -
Page 7: System Assembly
Section IV: System Assembly A. Assembling Roll Die to Die Shaft: (applies only to 13” systems and above, for 10” systems see “Illustrated Parts” section). On a clean, level bench; prepare the die for assembly by gently placing it in the “V” blocks provided. Ensuring the blocks are located under the bearers of the die and not on the image. - Page 8 Section IV: System Assembly C. Connections: Position the HP-3002 temperature control unit on a flat, level surface near the intended station and within easy reach of the operator. Connect power cord to die shaft assembly by inserting plug into receptacle and turning clockwise to lock. Repeat procedure at control unit.
-
Page 9: System Startup And Adjustments
Section V: System Startup and Adjustments NOTE: Foil positioning, tension, and process temperature will all vary somewhat depending on differences in print patterns, substrates, press speeds, foil performance, etc. Some experimentation may be necessary to obtain the best results with your application. -
Page 10: System Maintenance
Weekly Inspect shaft bushings for excessive wear or cracks due to shock. The shaft assembly needs to be returned to DMS to have new bushings installed, as special tools and fixtures are required for this procedure to ensure proper operation. -
Page 11: Appendix A: Illustrated Parts List
APPENDIX A Illustrated Parts List... -
Page 12: Appendix B: Hot Stamping Tips & Tricks
APPENDIX B Hot Stamping Tips & Tricks... - Page 13 In the DMS Foil Printing System, the die is a CNC and/or photo engraved hand-finished brass roll. The die is mounted on a custom-engineered shaft/heater assembly.
- Page 14 Build-up can be removed by using the supplied cleaning brush, wood, or lead to scrape the surface of the die. Return the die to DMS if there is any fear of damaging the die.
Need help?
Do you have a question about the FR Series and is the answer not in the manual?
Questions and answers