Bosch Professional GSC 12V-13 Original Instructions Manual page 11

Only use the battery with products from the manufac-
u
turer. This is the only way in which you can protect the
battery against dangerous overload.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for cutting sheet metals without
incurring any loss from chipping. It is suitable for straight
and curved cuts.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Battery release button
(2) Battery
(3) Button for battery charge indicator
(4) Battery charge indicator
(5) On/off switch
(6) Chip deflector
(7) Handle (insulated gripping surface)
(8) Fastening screw for top cutter
(9) Top cutter
(10) Bottom cutter
(11) Set screw for top cutter
(12) Fastening screw for bottom cutter
a)
(13) Setting gauge
(14) Hex key
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Cordless metal shears
Article number
Rated voltage
No-load stroke rate n
0
Max. steel sheet cutting ca-
A)
pacity
Smallest curve radius
Bosch Power Tools
Cordless metal shears
Weight according to
EPTA-Procedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
ure during operation
during storage
Recommended batteries
Recommended chargers
A) Refers to steel sheets of up to 400 N/mm
B) Depends on battery in use
C) Limited performance at temperatures <0 °C
Noise/Vibration Information
Noise emission values determined according to
EN 62841‑2‑8.
Typically, the A-weighted sound pressure level of the power
tool is less than 70 dB(A). The noise level when working can
exceed the volume stated. Wear hearing protection!
Vibration total values a
determined according to EN 62841‑2‑8:
a = 7 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
GSC 12V-13
Battery Charging
3 601 J26 1..
u
V= 12
-1
min 3600
mm 1.3
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
mm 15
before using your power tool for the first time.
C)
and
(triax vector sum) and uncertainty K
h
2 2
, K = 1.5 m/s .
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
1 609 92A 6N5 | (10.06.2021)
English | 11
GSC 12V-13
B)
kg 1.4–1.6
°C 0 to +35
°C −20 to +50
GBA 12V...
GAL 12...
GAX 18...
2