Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for biozoom VITALITY CHECK MSRRS SCN05
Summary of Contents for biozoom VITALITY CHECK MSRRS SCN05
- Page 1 User Manual...
-
Page 2: Table Of Contents
PREPARATION BEFORE STARTING A MEASUREMENT ........ 16 PERFORMING MEASUREMENTS ............... 16 GENERAL ASPECTS INFLUENCING THE LEVEL OF MEASURED RESULTS ..18 12 TROUBLESHOOTING ................19 13 MAINTENANCE AND CLEANING ............... 21 14 TECHNICAL SPECIFICATION ..............22 15 CERTIFICATIONS ..................23 biozoom copyright© 2021... -
Page 3: How To Get Started
RF signals from the device. Keep the device away from medical devices, including pacemakers and hearing aids, as they might malfunction and cause serious injury or death to the user and others. biozoom copyright© 2021... -
Page 4: Intended Use
ATTENTION V I T A L I T Y C H E C K is not a medical product and is not intended to diagnose, treat, cure or prevent any disease. Measure on uninjured bare skin only! biozoom copyright© 2021... -
Page 5: System Requirements
The scanner consists of a lid and the base. To open the scanner, hold the base and turn the lid counterclockwise by a few degrees (Figure open open Figure 1 biozoom copyright© 2021... - Page 6 • Cyan color: update mode • White: USB connected, disconnect USB to enter measurement mode The progress indicator (5) shows the progress. The displayed information has different meaning for every status. See chapter 12 for more information. biozoom copyright© 2021...
-
Page 7: Charging Of Battery
USB Type-C Figure 3 Attention Performing a measurement and charging of the battery at the same time is not possible because charging can influence the quality of the measurement. Please remove the USB cable before starting a measurement. biozoom copyright© 2021... -
Page 8: Turning The Device On And Off
3). Under this condition the scanner does not open its WiFi. Please disconnect the USB cable if you like to measure. If the device does not switch on, the battery may be completely empty. In this case, please charge the battery (chapter 8). biozoom copyright© 2021... -
Page 9: Steps For Performing A Measurement
(step 11 – step 14). Some of the steps are alternative steps and are displayed only when necessary. The connection process is fast and simple and must furthermore be performed only once if you always use the same scanner. biozoom copyright© 2021... - Page 10 LED If have used lights blue QR-Code press scanning “ALLOW” QR-Code Step 8.1 Step 9 Step 10 Step 10.1 Check scanner Identification enables Permission to scan Identification by status connection with phone QR-code typing serial number biozoom copyright© 2021...
- Page 11 Please note that the V I T A L I T Y C H E C K app stores only the last connection data. Therefore, you must conduct the connection operation again when you have connected a second scanner with your phone/tablet and you like to use now the first scanner once again. biozoom copyright© 2021...
-
Page 12: Performing Measurements
At that time, the hand should not be moved on the sensor to avoid a miss reading. The progress indicator LEDs on the scanner shows the progress. A green bar on the app indicates the progress too (Figure 7). biozoom copyright© 2021... - Page 13 When measuring for the first time, you must allow the app to send your measurement result to the website. To avoid this procedure for the next time please press the button “Don’t ask again”. Then press “Next” to get the result. (Figure 9) biozoom copyright© 2021...
- Page 14 This is the ideal time to change the modes. This can be done in the settings menu under “Wifi query” (Press on the three-bar symbol in the upper left corner of the app and select “Settings” and then select “WIFI query”. Then press the button “DEACTIVATE”, Figure 11). biozoom copyright© 2021...
- Page 15 Of course, you can activate the “WIFI query” again. It is recommended that the user starts with the standard configuration and select the alternative only after he has learnt the optimal handling. Drücke Drücke Drücke „Einstellu “Menü” “WLAN ngen“ Verbindungs anfrage” Drücke “Deaktivieren” Figure 11 biozoom copyright© 2021...
-
Page 16: Measurement Basics
But if your contact pressure is ideal you still get a little bit better result. Pushing blood out of the skin will make the measurement of heart rate variability completely (HRV) impossible (relevant only for models which measure HRV). biozoom copyright© 2021... - Page 17 To make sure not to move your hand after the measurement has started, avoid correcting the position of the hand on the scanner after the skin touches the scanner. Use the groove to align the hand precisely Do not move your hand while measuring Figure 13 biozoom copyright© 2021...
-
Page 18: General Aspects Influencing The Level Of Measured Results
Sunlight is even stronger and can get through all of your hand. That is why the biozoom sensor does refuse to measure in direct sunlight. If you want the maximum precision, you can help the sensor by making sure no bright light hits the back of your hand while measuring. -
Page 19: Troubleshooting
3. Switch on again by pressing the ON/OFF button for 1 second. Since the scanner will indicate its status by lighting of a specific color or a combination of colors of different indicators the table below has a ranking based on colors. biozoom copyright© 2021... - Page 20 Then follow the instructions of the app again. Scanner’s WIFI is activated Connection with phone/tablet is possible now. If a connection has already been established with this phone/tablet before, a new connection is automatically established when another measurement is conducted. biozoom copyright© 2021...
-
Page 21: Maintenance And Cleaning
V I T A L I T Y C H E C K , as these could damage the case and the optical surface of the sensor. If needed the sensor surface can be disinfected by wiping it with a cloth with 70% isopropanol. biozoom copyright© 2021... -
Page 22: Technical Specification
Use only as specified in this manual Model MSRRS SCN05 Electrical parameter 5V, 500mA max. Lithium-Ion battery Replace only with original battery from Biozoom Charging battery only in ambient temperature of +5°C … +40°C Operating temperature range 15° C … 35° C WiFi 2.4GHz, 54 MBps min., up to 3m range... -
Page 23: Certifications
Brand name: BIOZOOM Model No.: MSRRS SCN05 Complies with Battery: 3.7Vdc. 500mAh lithium ion IMDA Standards Manufacturer: biozoom services GmbH DA107248 Contains: CAUTION FCC ID: 2AC7Z-ESPWROOM-32E RISK OF EXPLOSION IF BATTERY REPLACED BY AN IC: 21098-ESPWROOM-32E INCORRECT TYPE. MIC 217-204070...
Need help?
Do you have a question about the VITALITY CHECK MSRRS SCN05 and is the answer not in the manual?
Questions and answers