Aqua-Air Wet/Dry 130 Owner's Manual
  1. Manuals
  2. Brands
  3. Aqua-Air Manuals
  4. Cleaning Equipment
  5. Wet/Dry 130
  6. Owner's manual

Aqua-Air Wet/Dry 130 Owner's Manual

Built-in total cleaning system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Models 130, 150,158, 230, and 250, 258
AQUA-AIR
Built-in Total Cleaning System
READ MANUAL BEFORE OPERATING SYSTEM
TO THE OWNER:
Read the owner's manual thoroughly to ensure the most efficient use
of your AQUA-AIR Wet/Dry
register your AQUA-AIR Wet/Dry
the warranty card located in this book.
TO THE INSTALLER:
AQUA-AIR Wet/Dry
installed in accordance with the "Installation Guide for AQUA-AIR
®
Wet/Dry
Built-in Total Cleaning System." The AQUA-AIR Wet/Dry
Built-in Total Cleaning System piping and waterlines are considered
part of the appliance in many jurisdictions. However, it is advisable
to verify local codes and guidelines with regard to water lines and
drains.
Please leave this manual and warranty information on the
power unit or with customer when installation is completed.
Owner's Manual
For your new
®
Built-in Total Cleaning Systems must be
Wet/Dry
®
Built-in Total Cleaning System. To
®
System warranty, fill in and mail
®
®

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Wet/Dry 130 and is the answer not in the manual?

Questions and answers

Virginia Thompson
March 3, 2025

My water connector won’t connect

0
1 comments:
Mr. Anderson
May 14, 2025

The water connector on the Aqua-Air Wet/Dry 130 may not connect if you are not pressing back the outer ring on the quick coupler socket before inserting the water hose end. Make sure to press back the ring and insert the hose fully into the socket.

This answer is automatically generated

0

Summary of Contents for Aqua-Air Wet/Dry 130

  • Page 1 TO THE INSTALLER: ® AQUA-AIR Wet/Dry Built-in Total Cleaning Systems must be installed in accordance with the “Installation Guide for AQUA-AIR ® ® Wet/Dry Built-in Total Cleaning System.” The AQUA-AIR Wet/Dry Built-in Total Cleaning System piping and waterlines are considered part of the appliance in many jurisdictions.

  • Page 3: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS CLEANING SYSTEM WARNING To reduce the risk of fire, electric shock or injury:  Unplug and disconnect power before servicing. ...

  • Page 4: Power Unit

    POWER UNIT WARNING - DO NOT OPERATE CLEANING SYSTEM EITHER FOR DRY VACUUMING OR WET CLEANING WITHOUT COLD WATER RINSE ON. UTILITY REQUIREMENTS: ELECTRICAL: 120 volt, 60 hertz, Model model130/150/158 15 amp standard plug Model 230/250/258 (2) 15 amp standard plugs Power unit should be plugged into dedicated grounded outlet.
  • Page 5 POWER UNIT ELECTRONIC MOTOR MONITOR: The Control Panel Indicator light on the upper left side of the power unit monitors the operating condition of the motor by displaying the following colors: Green Light Monitor is operating (In the event of the motor failing to operate or is unusually noisy - call you dealer for service.) Orange Light...

  • Page 6: Grounding Instructions

    GROUNDING INSTRUCTIONS Connect to a properly grounded dedicated outlet only  This appliance must be grounded.  If it malfunctions or breaks down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. ...

  • Page 7: Troubleshooting Guide

    Check your main fuse or circuit breaker at the main power supply.  If necessary replace burnt fuse or reset breaker. ® Check the reset button on the left side of the AQUA-AIR Wet/Dry   power unit. Pressing button should restore service.
  • Page 8 Automatically mixes pre-spray or extraction rinse cleaning solutions. *IMPORTANT* This injector is designed specifically to dispense AQUA-AIR Wet/Dry ® cleaning concentrate. The use of carpet shampoo, all-purpose or auto- mobile cleaners will result in clogging of injector and over-foaming of the extractor.

  • Page 9: Wiring Diagram

    WIRING DIAGRAM 230/250/258 CONTROL MODULE 130/150/158 CONTROL MODULE...
  • Page 10  If possible, leave holding tank (bottom chamber of the power unit) open when not in use to air out. Depending on use, sucking a gallon of premixed Aqua-Air Bio-enzyme cleaner/degreaser - Part #SC05GL (8 oz in one gallon of warm water) will freshen hoses, piping and holding tank.
  • Page 11 Agitate with soft brush on heavier soils. Allow 5-10 minute dwell time. Extract soils and solution out with the AQUA-AIR Wet/Dry ® extraction tools. Accelerate drying of the carpet or fabric with fans, air movers and dry air.
  • Page 12 AQUA-AIR automated pre-spray injector: Adjust to inject 3 to 8 ounces of commercial heavy duty pre-spray per gallon of water. Spray the carpets and fabric then rinse with hot water using the AQUA-AIR hand tool. ® Vacuum dry with the AQUA-AIR Wet/Dry system.
  • Page 13 Allow solution to dwell for 20-30 minutes, if possible. Rinse/Extract with warm water, using the AQUA-AIR upholstery tool. Apply a light mist (diluted) on affected area and allow to dry normally. General Deodorizing Dilute 1 part Multi Surface cleaner with 4 parts warm water.
  • Page 14 Dry Vacuuming Attach the curved wand of the dry vacuum hose to the dry vacuum tool to be used. Insert the hose cuff with the metal end into vacuum inlet valve. This will automatically turn on the system (hose with on/off switch on handle must be turned on to operate).
  • Page 15 Insert the hose cuff with the metal end into vacuum inlet valve. This will automatically turn the system on. (With surface mounted vacuuming inlets with on/off switch, turn switch on to operate). For systems with AQUA-AIR Wet/Dry ® cleaning solution injector, insert the appropriate cleaning compound in the injector. For systems without the injector, pre-spray surface to be cleaned with appropriate cleaning compounds.
  • Page 16 Dry Vacuuming Attach the curved wand of the dry vacuum hose to the dry vacuum tool to be used. Insert the hose cuff with the metal end into vacuum inlet valve. This will automatically turn on the system (hose with on/off switch on handle must be turned on to operate).
  • Page 17 Most natural hardwood has been coated with a urethane or wax finish. Chemical residues left behind by household and commercial cleaners can ® prematurely damage these finishes. Using the Aqua-Air Wet/Dry process will help ensure extended life and appearance of your hardwood floor.
  • Page 18 Tile and grout will be clean and instantaneously dry. CLEANING PROCESSES & PROCEDURES Linoleum, Vinyl, Stone, Concrete etc. All of these surfaces can and should be cleaned using the Aqua-Air Wet/Dry ® process. These surfaces should be cleaned using the "hard- wood" or "tile &...
  • Page 19 30 days and residential or commercial use stated. Warranty shipping policy: Customer is to return defective item to AQUA-AIR paying for any necessary shipping costs, and AQUA-AIR upon receiving the defective item, will return repaired/replaced item via standard ground shipping...
  • Page 20 30 days and residential or commercial use stated. Warranty shipping policy: Customer is to return defective item to AQUA-AIR paying for any necessary shipping costs, and AQUA-AIR upon receiving the defective item, will return repaired/replaced item via standard ground shipping...
  • Page 21 30 days and residential or commercial use stated. Warranty shipping policy: Customer is to return defective item to AQUA-AIR paying for any necessary shipping costs, and AQUA-AIR upon receiving the defective item, will return repaired/replaced item via standard ground shipping...
  • Page 22 Manufactured by AQUA-AIR MANUFACTURING 47 East 800 South, Ivins, Utah 84738 (800) 916-5777 or (435) 673-5712 FAX (435) 986-4128 www.aquaair-wetdry.com...

This manual is also suitable for:

Wet/dry 150Wet/dry 158Wet/dry 230Wet/dry 250Wet/dry 258

Table of Contents