Summary of Contents for Honda Electronics HE-7301II
- Page 1 HE-7301Ⅱ HE-1501 GPS COLOR LCD PLOTTER SOUNDER HE-7302Ⅱ HE-1502 GPS COLOR LCD PLOTTER...
- Page 2 INTRODUCTION We thank you very much for your purchasing our product. ■ Please be sure to read this operation manual carefully and understand what it describes before you operate this unit in order to keep your safety. ■ After you read this manual, please keep it at the place where you will not lose or break so as to read soon when it is necessary.
-
Page 3: Table Of Contents
CONTENTS CAUTION ON SAFETY (PLEASE MAKE SURE TO READ) ··························· 1 1. HANDLING OF MAIN UNIT ············································· 1 2. HANDLING OF CABLES ··············································· 2 3. HANDLING OF TRANSDUCER AND WATER TEMPERATURE SENSOR ··············· 3 4. HANDLING OF REMOTE ················································ 3 5. HANDLINF OF GPS ANTENNA ··········································· 4 6. TFT LCD PANEL····················································· 4 7. CAUTION ON OPERATION ·············································· 5 FEATURES ······························································· 6 DESCRIPTIONS ··························································· 7 1. FRONT PANEL······················································· 7 2. REAR SIDE························································· 9 3. REMOTE··························································· 10 HOW TO SEE THE DISPLAY ················································ 13 HOW TO OPERATE MENU ···················································... - Page 4 TO EDIT EVENT MARK ···················································· 33 TO SHOW (RECORD) WAKE ················································· 35 TO ERASE WAKE ························································· 36 TO MEMORIZE (SHOW) WAYPOINT MARK ······································ 38 TO ERASE WAYPOINT MARK ················································ 39 TO EDIT WAYPOINT MARK ················································· 41 TO SET WAYPOINT NAVIGATION ············································ 43 TO CLEAR WAYPOINT NAVIGATION ·········································· 44 TO DRAW LINE ·························································· 45 TO ERASE LINE ························································· 46 TO REGISTER (ERASE) ROUTE ············································· 48 TO RECALL REGISTERED ROUTE (SETTING ROUTE NAVIGATION)·················· 49 TO ADVANCE WAYPOINT/TO RETURN WAYPOINT ································ 50 TO SHOW DEPTH LINE ···················································· 51 TO INDICATE PLACE NAME, TIDE, CURRENT AND ETC.
- Page 5 OPERATION OF FISH FINDER (FOR HE-7301II, HE-1501) HOW TO SEE THE DISPLAY OF FISH FINDER MODE ···························· 80 TO SET THE DEPTH (DISPLAY RANGE) ······································ 81 TO ADJUST SENSITIVITY ················································· 82 TO SET SHIFT (DISPLAY RANGE SHIFT) ···································· 84 TO MOVE EXPANDED AREA ················································· 85 TO SHOW/SET THE EXPANSION MODE ········································ 86 TO SET WATER TEMP. ALARM ·············································· 87 TO SET FISH ALARM ····················································· 87 TO SET DEPTH ALARM ···················································· 88 TO SET CORRECTION OF WATER TEMP. ······································ 88 TO SHOW DUAL FREQUENCY DISPLAY ········································ 89 ...
- Page 6 CAUTION WHEN OTHER GPS RECEIVER THAN STANDARD SUPPLIED IS CONNECTED··· 101 INSTALLATION OF MAIN UNIT ············································ 102 INSTALLATION OF MAIN UNIT ONTO DASHBOARD ····························· 104 INSTALLATION OF TRANSDUCER ··········································· 108 THRU-HULL INSTALLATION ············································· 108 INSTALLATION OF WATER TEMP. SENSOR ··································· 109 STANDARD COMPOSITION ················································· 110 OPTION PARTS ························································· 111 GENERAL INFORMATON OF FISH FINDER ···································· 112 TROUBLE SHOOTING ····················································· 114 SPECIFICATIONS ······················································· 117 ...
-
Page 7: Caution On Safety (Please Make Sure To Read)
CAUTION ON SAFETY (PLEASE MAKE SURE TO READ) This section explains the important cautions in order to prevent the person who will use our product or other persons from human damage or damage to their property. 1.HANDLING OF MAIN UNIT ... -
Page 8: 2. Handling Of Cables
Do not install at the place where rain or spray dashes directly. ● It causes to firing or injuring. Do not install at the place where it becomes hot. ● It causes to firing, human damage or electric shock due to increasing ... -
Page 9: Handling Of Transducer And Water Temperature Sensor
HANDLING OF TRANSDUCER AND WATER TEMPERATURE SENSOR ●Work on the board is too unstable and risky. Installation and maintenance of transducer and water temperature sensor should be done after you land and fix the boat. ... -
Page 10: Handlinf Of Gps Antenna
HANDLING OF GPS ANTENNA ●Work on the board is too unstable and risky. Installation and maintenance of GPS antenna should be done after you land and fix the boat. Unless you ... -
Page 11: 7. Caution On Operation
7. CAUTION ON OPERATION Be sure to put the power switch off when you start to run the engine. When the engine starts to run, voltage of battery varies heavily. It may influence ... -
Page 12: Features
FEATURES ★Process of drawing coastlines at high speed! High performance CPU enables you to draw coastlines at high speed. ★ Keys on panel let you simple operation of various functions ... -
Page 13: Descriptions
DESCRIPTIONS FRONT PANEL ●HE-7301Ⅱ, HE-1501 Front Panel Infrared ray sensor POWER KNOB CURSOR ON/OFF（→page 24） Power ON/OFF（→page 16） Switch display/non display of cursor. Adjust brightness（→page 20） ... - Page 14 ●HE-7302Ⅱ, HE-1502 FRONT PANEL Infrared ray sensor POWER KNOB WAKE ON/OFF（→page 38） Power ON/OFF（→page 16） Switch display or non display of wake. Adjust brightness（→page 19） WAKE COLOR（→page 38） ...
-
Page 15: Rear Side
REAR SIDE Power Supply for monitor(5P)(Option) ... -
Page 16: Remote
３. REMOTE (OPTION) RANGE (for HE-7301Ⅱ) （→page 73） Set displayed depth range. *Enter specified event mark.（→page 60） GAIN 2 （→page 75） (for HE-7301Ⅱ) Adjust sensitivity of left display on dual ... - Page 17 MODE（→page 18） ・It switches Fish Finder mode and Plotter mode (for HE-7301Ⅱ). CENTER key ・Move map and cursor. ・It is also used to select menu item. DETAILED (EXPANSION) （→page 26） Enlarge displayed map (detail) ...
- Page 18 HOW TO PUT BATTERIES Loose two screws and take off the rear cover. Put the batteries in correct polarity. Do not fasten screws strongly. ※ CAUTION ON BATTERIES 【...
- Page 19 ※ Display is HE-7301Ⅱ. On the HE-7302Ⅱ, fish finder display on right side of screen is not shown.
-
Page 20: How To Operate Menu
HOW TO OPERATE MENU How to operate menu You can change contents of item which you set by selecting menu item using [MENU] key, [CENTER] key, {SET} key and [CLR] key. CLR key MENU key ... -
Page 21: Basic Operation
BASIC OPERATION POWER ON/OFF······················································ 16 HOW TO CHANGE THE DISPLAY ····································· 17 TO CONTROL BRIGHTNESS OF SCREEN······························ 19 TO SHOW SIMULATION DISPLAY····································· 19 ... -
Page 22: Power On/Off
POWER ON/OFF Power ON/OFF POWER Knob By turning [POWER] knob clockwise, alarm comes on and power turns ON. If firstly [NOTE] is shown and map is continuously shown, starting is complete. ... -
Page 23: To Change The Display
HOW TO CHANGE THE DISPLAY Change the display In case of 《 HE-7301Ⅱ》 Each time when you press [MODE] key, display changes to [Fish Finder], [Plotter & Fish Finder] ... - Page 24 Change of display division proportion 【 】 When [Plotter & Fish Finder] display is shown, you can change the display division proportion by pressing [S] key and [PL] key for a long time. ...
-
Page 25: To Control Brightness Of Screen
TO CONTROL BRIGHTNESS OF SCREEN Control of brightness Adjust brightness by turning [POWER] knob of main unit. Turn POWER knob clockwise Screen becomes ： light. Turn POWER knob counterclockwise: Screen ... -
Page 26: Operation Of Plotter
OPERATION OF PLOTTER TO USE THE CURSOR ·················································· 21 TO MOVE THE DISPLAY ··············································· 22 TO ENLARGE/REDUCE THE PICTURE ···································· 23 SELECT THE DISPLAY DIRECTION ································· 24 TO SET RANGE YOU ALWAYS USE ········································ 24 TO USE MAP CARD ·····················································... -
Page 27: To Use The Cursor
TO USE THE CURSOR ON/OFF of Cursor Following operations are available by cursor. Latitude/longitude at optional position of ・ display are shown. Distance, direction and required time from ・ own boat position to cursor are shown. ... -
Page 28: To Move The Display
TO MOVE THE DISPLAY Movement of display Erase cursor pressing [CURSOR ON/OFF] key. Display moves up/downward or left/rightward with key. CENTER key CURSOR ON/OFF key 【Movement of display】 ... -
Page 29: To Enlarge/Reduce The Picture
TO ENLARGE/REDUCE THE PICTURE Enlarging and reducing picture 【Expansion/Reduction of display】 When the cursor is indicated, display expands/ reduces at center of cursor’s position. When the cursor is not indicated, display expands/reduces ... -
Page 30: To Select The Display Direction
TO SELECT THE DISPLAY DIRECTION Selection of direction Either NORTH UP or COURSE UP is selected by pressing [NORTH UP] key or [COURSE UP] key. [NORTH UP]: Just upper of display becomes ... -
Page 31: To Use Map Card
TO USE MAP CARD Coastline Data Inserting Card】 【 Take off card slot cover on the side of main unit. Insert the map card into card connector while sticker side faces ahead. ... -
Page 32: To Use Memory Card
TO USE MEMORY CARD データのコピー Copy of data 【Memory card】 Data can be copied between main unit and memory card. Memory card you can use is limited to our made card. 【Contents which can be copied】... - Page 33 Store data from unit to card CLR key Select [8.OTHERS]→ [2.MEMORY CARD]→ [2.STORE FROM UNIT TO CARD] on menu and press （right）of CENTER key. Enter block number of card which you store by ...
- Page 34 Store data from card to unit CLR key Select [8.OTHERS] → [2.MEMORY CARD] → [3.STORE FROM CARD TO UNIT] on menu and press （right）of [CENTER] key. Enter block number of card which you store by ...
-
Page 35: To Enter Event Mark
TO ENTER EVENT MARK To enter event mark at own boat’s position CURSOR ON/OFF key Press [EVENT MARK] key. Event mark is shown at the position of own boat’s mark. ※By pressing [EVENT MARK] key when cursor ... - Page 36 To enter event mark with fish finder key ※This function is effective at Plotter display only in case of HE-7301Ⅱ. This function can not be used at Fish Finder display or Fish Finder/Plotter display. ※Event mark key is used in case of HE-7302Ⅱ.
-
Page 37: To Erase Event Mark
TO ERASE EVENT MARK To erase by color All event marks which are selected by each color are erased. Select [3. EVENT MARK] → [1.ERASE] → 「 1. ERASE BY COLOR」on menu. ... - Page 38 To erase by cursor Note 1 ） When unit is delivered from factory, [3.EVENT MARK] → [1.ERASE] → [1.ERASE BY CURSOR] on menu is set to OFF. (→page 64) Set [ERASE BY CURSOR] to ON to operate this function. ...
-
Page 39: To Edit Event Mark
TO EDIT EVENT MARK To edit event mark You can edit shape, color, latitude and longitude at every event mark manually. You can also enter comment (name). CLR key MENU key ... - Page 40 【Enterable characters】 Symbol, number, alphabet (Capital, Small) and Katakana (Japanese character) can be entered. 【Operation during Edit mode】 of [CENTER] key ：Select character and mark. of [CENTER] key ：Move cursor before and after. ...
-
Page 41: To Show (Record) Wake
TO SHOW (RECORD) WAKE Show (Record) of wake By pressing [ WAKE ON/OFF] key, wake is recorded. WAKE ON/OFF key Previous recorded wake is also indicated again. ”which indicates “During recording wake” “... -
Page 42: To Erase Wake
【Upper limit of recording】There is upper limit of wake which you can record. Maximum numbers of point which you can store is 32,000 points. When wake points exceed 32,000 points, wake from the oldest is erased. When you said for a long time ... - Page 43 To erase wake by cursor Note 1) When unit is delivered from factory, [1.WAKE]→[4.ERASING WAKES]→ [3.ERASE BY CURSOR] is set to OFF. (→page 63) Set [ERASE BY CURSOR] to “ON” to execute this function. ...
-
Page 44: To Memorize (Show) Waypoint Mark
TO MEMORIZE (SHOW) WAYPOINT MARK To memorize (show) waypoint mark 【Waypoint Mark】 Waypoint mark is mark that indicates “destination” or “turning point”. ・Shape：8 types（ ） ・Indicated Color：Red, Yellow, Green, Magenta, White, Cyan, Blue, Wake color ... -
Page 45: To Erase Waypoint Mark
TO ERASE WAYPOINT MARK To erase waypoint by color All waypoint marks which are selected by each color are erased. Select [2.WAYPOINT]→[3.ERASE WAYPOINT] →[1.ERASE BY COLOR] on menu. Select and designate color among [1.ERASE BY ... - Page 46 To erase waypoint marks by cursor Note 1) When unit is delivered from factory, [2.WAYPOINT]→[3.ERASE]→[4.ERASE BY CURSOR] is set to OFF. (→page 63) Set [ERASE BY CURSOR] to “ON” to execute this function. CURSOR ON/OFF key By pressing [CURSOR ON/OFF] key, cursor is ...
-
Page 47: To Edit Waypoint Mark
TO EDIT WAYPOINT MARK To edit waypoint mark You can edit shape, color, latitude and longitude at every waypoint mark manually. CLR key MENU key Indicated List ... - Page 48 【Enterable characters】 Symbol, number, alphabet (Capital, Small) and Katakana (Japanese character) can be entered. 【Operation during Edit mode】 of [CENTER] key ：Select character and mark. of [CENTER] key ：Move cursor before and after. ...
-
Page 49: To Set Waypoint Navigation
TO SET WAYPOINT NAVIGATION Setting of waypoint navigation When you set waypoint navigation, from own boat’s position to waypoint is connected by line, and latitude/longitude of waypoint, distance, bearing and estimated time of arrival from own ... -
Page 50: To Clear Waypoint Navigation
Setting of Simple Waypoint Navigation WP SAVE key By pressing [ CURSOR ON/OFF] key, cursor is indicated. Move cursor to point to be waypoint with key. By pressing [WP SAVE] key for a long time, ... -
Page 51: To Draw Line
TO DRAW LINE Drawing Line 【Line】 You can draw line on any position of display as you want. By pressing [CURSOR ON/OFF] key, cursor is shown. Select [8.OTHERS] →... -
Page 52: To Erase Line
Distance between two points】 【 When line is drawn, distance from a previous position (point) to “Cursor” position is indicated. You can know the distance between any two points. 【Line Color】 Each time when you press [WAKE COLOR] key, color changes. Color can be ... - Page 53 To erase line by cursor stacking cursor line, erase line respectively. It is necessary to make effective of CLR key CURSOR ON/OFF key function [ERASE BY CURSOR] on menu beforehand in order to achieve this function.（→ ...
-
Page 54: To Register (Erase) Route
TO REGISTER (ERASE) ROUTE To register (erase) route 【Route】 Line connected between intermediate points is called “Route” and it is indicated by points and lines. 【Number of registered route】 You can enter maximum 20 intermediate points (course change points) for one route ... -
Page 55: To Recall Registered Route (Setting Route Navigation)
TO RECALL REGISTERED ROUTE (SETTING ROUTE NAVIGATION) Recalling route (Setting route navigation) Select [4.ROUTE] → [1.RECALL ROUTE] on menu. Enter route number. Route navigation is set by pressing [SET] key. ... -
Page 56: To Advance Waypoint/To Return Waypoint
TO ADVANCE WAYPOINT/TO RETURN WAYPOINT To advance/return waypoint When route navigation is set, waypoint line is switched to next intermediate point (course change point) on route in turn. Waypoint Line: Line connected between own ... -
Page 57: To Show Depth Line
TO SHOW DEPTH LINE To show depth line 【Depth Line】 Depth line is line that same deep bottoms are connected. You can show or erase the depth line ... -
Page 58: To Show Latitude/Longitude Line (Grid)
After you finish menu, adjust range with [EXP] key, [RED] key or 〔 〕key and then indicate place name, other name, fish shoal, lighthouse and etc. Range Change key RANGE Change key ... -
Page 59: Own Boat's Vector And Color Of Own Boat's Mark
Anchor watch alarm： When own boat drifts beyond specified distance (circle) from it’s waypoint or route point, alarm sounds. Off course alarm: When own boat strays out of a specified ... -
Page 60: To Set Readout Accuracy Of Each Information
TO SET READOUT ACCURACY OF EACH INFORMATION To set readout accuracy of each information You can change readout accuracy of position, boat speed, distance, bearing and etc. (→page Example: Change of bearing readout accuracy ... -
Page 61: To Show Own Boat Position With Time Difference Of Loran C
TO SHOW OWN BOAT POSITION WITH TIME DIFFERENCE OF LORAN C To show with time difference of Loran C 【Loran C】 Loran C (Long Range Navigation) is hyperbolic navigation system using long wave ... -
Page 62: To Set Dgps Beacon Receiver
TO SET DGPS BEACON RECEIVER To set DGPS beacon receiver (for only DGPS model) 【DGPS】This system makes GPS accuracy improve using electric wave transmitted from beacon station (medium frequency band beacon signal). ... -
Page 63: To Allocate Fish Finder Key To Plotter Key
TO ALLOCATE FISH FINDER KEY TO PLOTTER KEY To allocate fish finder key to plotter key When display is plotter mode, you can allocate fish finder key on remote to plotter key (Remote is option.) ... -
Page 64: List Of Plotter Menu And Meaning
LIST OF PLOTTER MENU AND MEANING Menu Item Meaning of setting 1. Wake ON ：Show (record) wake 1. WAKE OFF ：Not show wake (interrupt to record) MEMORY 2. WAKE Set color of wake which is being recorded. COLOR Selected color is indicated. - Page 65 Menu Item Meaning of setting 3. EVENT MARK 1. ERASE 1. ERASE BY COLOR Erase all event marks of which color is designated. 2. ERASE BY SHAPE Erase all event marks of which shape is designated. 3.
- Page 66 Menu Item Meaning of setting 6. READOUT SETTING 1. C-MAP 1. DEPTH SETTING 1. DEPTH UNIT Select "M", "Ft" or "Fa" SETTING 2. SOUNDING LINE ON : Indicate OFF : Not indicate 2. LAT/LON GRID ON : Indicate OFF : Not indicate ...
- Page 67 Menu Item Meaning of setting 4. CURSOR 1. CURSOR STYLE Designate cursor shape. Select with left/right of CENTER key. + READOUT 2.CURSOR COLOR Designate cursor color. Select with left/right of CENTER key. YELL 3.CURSOR LINE Designate whether cursor is shown or not.
- Page 68 Menu Item Meaning of setting 1. INITIALIZE Initialize memory card. 2. MEMORY CARD MEMORY CARD 2. STORE FROM Store information set in main unit into memory card. (→page 30) UNIT TO CARD 3. STORE FROM Reading information stored in memory card into main CARD TO UNIT unit.
- Page 69 OFF：To save power consumption, stop fish finder operation 2.F/F OPERATION at plotter display mode. (→page 18) AT PL ON ：Fish finder operates at PL display mode. （HE-7301II, HE-1501) 3.WAYPOINT Select whether waypoint mark comment entered on menu 2. WAYPOINT COMMENT 7.LIST/EDIT is indicated on map or not.
-
Page 70: C-Map Instruction
C-MAP INSTRUCTION 1.ADDITIONAL C-CARDS ................. 66 2. MAP SETTING....................67 1. Set the depth unit....................67 2. Set if DEPTH LINE is displayed or not............67 3. Set if LAT/LON GRID is shown or not.............. 67 4. Set if LIGHT SECTOR is shown or not............. 68 5. - Page 71 C-MAP INSTRUCTION 1.ADDITIONAL C-CARDS ................. 66 2. MAP SETTING ....................67 1. Set the depth unit....................67 2. Set if DEPTH LINE is displayed or not.............67 3. Set if LAT/LON GRID is shown or not...............67 4. Set if LIGHT SECTOR is shown or not.............68 5.
- Page 72 IMPORTANT INFORMATIONS SHOWN ON THE SCREEN OF THIS UNIT SHOULD NOT BE RELIED ON FOR NAVIGATION JUDEGMENT. OFFICIAL MARINE CHARTS SHOULD BE USED FOR JUDGEMENT. NT+, MAX data are not to be used a replacement for official paper chart.
-
Page 73: Additional C-Card
1. ADDITIONAL C-CARDS ●Up to two C-CARDs can be inserted. Card slot cove Take off card slot Loosen screw. cover. Insert the card. -
Page 74: 2. Map Setting
2. MAP SETTING Chart presentation can be customized according to user’s demand. Menu related to MAP SETTING is set within; →[6:READOUT SETTING→[1:C-MAP SETTING] Set the depth unit. [ m, Ft, Fa ] The default setting is "m". Depth unit to be used is changed with DEPTH LINE and SPOT SOUNDING. Select menu item with;... -
Page 75: Set If Light Sector Is Shown Or Not
Set if LIGHT SECTOR is shown or not. [ ON, OFF ] The default setting is "ON". Select menu item with; →[6:READOUT SETTING]→[1:C-MAP SETTING]→ [3:LIGHT SECTOR] and then select ON or OFF turning the lever left or right. LIGHT SECTOR Note) In case NAV-AIDS is set to INT Simple or US simple, LIGHT SECTOR is not shown even if LIGHT SECTOR is set to ON. -
Page 76: Set If Tracks, Route Is Shown Or Not
Set if TRACKS, ROUTE is shown or not. [ ON, OFF ] The default setting is "ON". Select menu item with; →[6:READOUT SETTING]→[1:C-MAP SETTING]→ [5:TRACKS,ROUTES] and then select ON or OFF turning the lever left or right. Set if NAME is shown or not. [ ON, OFF ] The default setting is "ON". -
Page 77: Set If Seabed Type Is Shown Or Not
Set if SEABED TYPE is shown or not. [ ON, OFF ] The default setting is "ON". Select menu item with; →[6:READOUT SETTING]→[1:C-MAP SETTING]→ [6:OTHER OBJECTS]→[3:SEABED TYPE] and then select ON or OFF turning the lever left or right. Set if WRECKS, Obstruction is shown or not. [ ON, OFF ] The default setting is "ON". -
Page 78: Set Navigational Aids
Set Navigational Aids. [ OFF US, US SMP INT ,INT SMP ] The default setting is "US". Select menu item with; →[6:READOUT SETTING]→[1:C-MAP SETTING]→ [7:OTHER SETTING]→[1:NAV-AIDS] and then set turning the lever left or right. When selected it affects Light,Signals,Buoys & Beacons display. : Draw Navigational Aids using NOAA symbology. -
Page 79: Set If Declutter Is On/Off
Set if DECLUTTER is ON/OFF. [ ON, OFF ] The default setting is "ON". Select menu item with; →[6:READOUT SETTING]→[1:C-MAP SETTING]→ [7:OTHER SETTING]→[3:DECLUTTER] and then select ON or OFF turning the lever left or right. When it is set to ON, overlapped text (for example, place name, etc.) is deleted. -
Page 80: Set If Auto−Course Up Is On/Off
Set if AUTO−COURSE Up is ON/OFF. [ ON, OFF ] The default setting is "OFF". Select menu item with; →[6:READOUT SETTING]→[1:C-MAP SETTING]→ [7:OTHER SETTING]→[5:AUTO-COURSE UP] and then select ON or OFF turning the lever left or right. When AUTO−COURSE Up is set to ON, if boat turned off more than ±15°... -
Page 81: 3. Getting Automatic Info
3. GETTING AUTOMATIC INFO When cursor is overlaid on object displayed on map, you can indicate name, etc. of the object on the screen. Information of displayed Cursor object is indicated. Select menu item with; →[6:READOUT SETTING]→[1:C-MAP SETTING]→ [8:AUTO INFO] and then select OFF or ON POINT,ON ALL turning the lever left or right. - Page 82 When AUTO info is indicated, all available information about graphic points under the cursor with pressing key. Info Tree is indicated on the upper of page and detailed information is indicated on the lower of page. You can select cursor on Info Tree turning up/down key up/downward. Detailed information about selected Object is indicated on the lower of page.
-
Page 83: 4. Find Function
4. FIND FUNCTION The chartplotter allows finding Port, Port, Services, Tide Station, Wrecks and Obstructions. Finding Port List of ports (maximum 8 ports) near to own boat (near to cursor when cursor is shown) is indicated. List is indicated with; →[7:FIND]→[1:PORT]→... -
Page 84: Finding Port Services
Finding Port Services List of facilities (for example, Hospital, Sailmarker, Bank, etc.) near to own boat (near to cursor when cursor is shown) is indicated. Icon of selectable services is indicated with; →[7:FIND]→[2:PORT SERVICES ]→ or [↑→↓←] When you select service with up/down key and press key, list (maximum 8 services) is indicated. -
Page 85: Finding Wrecks
Finding Wrecks List of Wrecks (maximum 8 wrecks) near to own boat (near to cursor when cursor is shown) is indicated. List is indicated with; →[7:FIND]→[4:WRECKS]→ When you select port with up/down key and press while list is indicated, map is redrawn so that selected Wrecks is shown at the center of screen. - Page 87 OPERATION OF FISH FINDER （for HE-7301Ⅱ,HE-1501） HOW TO SEE THE DISPLAY OF FISH FINDER MODE ···························· 80 TO SET THE DEPTH (DISPLAY RANGE) ······································ 81 TO ADJUST SENSITIVITY ················································· 82 TO SET SHIFT (DISPLAY RANGE SHIFT) ···································· 84 TO MOVE EXPANDED AREA ················································ 85 TO SHOW/SET THE EXPANSION MODE ········································ 86 TO SET WATER TEMP. ALARM ·············································· 87 TO SET FISH ALARM ····················································· 87 TO SET DEPTH ALARM ···················································· 88 TO SET CORRECTION OF WATER TEMP. ······································ 88 TO SHOW DUAL FREQUENCY DISPLAY ········································ 89 TO SET SWEEPING SPEED ·················································...
-
Page 88: How To See The Display Of Fish Finder Mode
HOW TO SEE THE DISPLAY OF FISH FINDER MODE Example of fish finder display (in case of showing fish finder display only) Differential Mark※ Frequency※ Fish School Own Boat position ... -
Page 89: To Set The Depth (Display Range)
TO SET THE DEPTH (DISPLAY RANGE) Depth (Display Range) Depth (Display Range) 【 】 This sets the depth (display range: how deep from the surface of water is displayed). Depth range you can set differs depends on frequency. ... -
Page 90: To Adjust Sensitivity
TO ADJUST SENSITIVITY In case of single frequency display This describes operation for single frequency display. ※You can change sensitivity with GAIN 1 key or GAIN 2 key. ※Single frequency display or dual frequency display is selected on menu. (→page 81) ... - Page 91 In case of remote 《 》 【To decrease sensitivity】 Each time when you GAIN1(L) key, gain bar becomes short and sensitivity decreases. 【To increases sensitivity】 Each time when you press GAIN1(H) key, gain ...
-
Page 92: To Set Shift (Display Range Shift)
TO SET SHIFT (DISPLAY RANGE SHIFT) Shift (Shift of display range) 【Shift (Shift of display range)】 You can shift the initial displayed depth downward. For example, when you shift 10m downward at 0-8m depth range, initial display ... -
Page 93: To Move Expanded Area
TO MOVE EXPANDED AREA To move expanded area You can move and see expanded area to top or bottom of display. ※You can not operate {ZOOM} key except for manual expansion mode. ... -
Page 94: To Show/Set The Expansion Mode
TO SHOW/SET THE EXPANSION MODE Expansion Mode 【Expanded display】 Expanded display is shown on the left half of screen. In case of dual frequency, frequency’s expanded display shown on right side of screen is ... -
Page 95: To Set Water Temp. Alarm
TO SET WATER TEMP. ALARM Water Temp. Alarm 【Water Temp. Alarm】 Alarm goes off within or out of two water temperatures (TEMP SET 1, TEMP SET 2). ※Optional water temp. sensor is required for this function. ... -
Page 96: To Set Depth Alarm
TO SET DEPTH ALARM Depth Alarm 【Depth Alarm 】 Alarm goes off within or out of two depths (DEPTH SET 1, DEPTH SET 2). Select [5.ALARM] → [5.DEPTH ALARM] → ... -
Page 97: To Show Dual Frequency Display
TO SHOW DUAL FREQUENCY DISPLAY Change of display Following dual frequency display can be selected. ※ 600W-200kHz, 1.2kW-200kHz or 3.0kW-200kHz does not have dual Select [9.SOUNDER]→[1.DISPLAY] on menu. frequency function. Establish [1.DISPLAY]. ... -
Page 98: To Set Auto Range (Automatic Range Control)
TO SET AUTO RANGE (Automatic Range Control) Auto Range Depth range is automatically changed so that the sea bottom is always shown on the optimum position of screen (lower half area). ... -
Page 99: To Set A-Mode
TO SET A-MODE A-Mode It is displayed on the right edge of screen (between fish finder display and depth calibration) and it’s width changes according to strength of reflected signal. Strong response is indicated thick and weak signal is indicated thin. ... -
Page 100: To Set Color Configuration
TO SET COLOR CONFIGURATION Color Configuration Reflected signal of sound wave is converted into 16 ranks of digital signal according to the strength of response. 7 ranks of color except background color is arranged and it ... -
Page 101: To Change Unit Of Depth Readout
TO CHANGE UNIT OF DEPTH READOUT Depth Unit “Meters”, “Fathoms”, “Feet” or “Brazas” is selected. Select [9.SOUNDER]→[8.OTHERS]→[1.DEPTH UNIT] on menu. Set [1.DEPTH UNIT]. (Meters, Fathoms, Feet, Brazas) ... -
Page 102: To Set Auto Range Max. Depth
TO SET WATER TEMP. GRAPH Water Temp. Graph Water temperature graph is shown on the screen. It enables you to know the variation of water temperature and recognize the turning of tide. ... -
Page 103: To Set Stc
TO SET STC This suppress sensitivity shallower than approx. 100m and eliminate reflected signal from plankton and air bubble. When STC is set to ON, sensitivity near sea surface decreases. When you increases ... -
Page 104: List Of Fish Finder Menu And Meaning
LIST OF FISH FINDER MENU AND MEANING Menu item Meaning of setting 9. SOUNDER 1. DISPLAY Switch single frequency display on dual frequency simultaneous display. ※It is shown when LOW+HIGH is selected only. LOW：only low freq. HIGH：only high freq. ※600W-200kHz, 1.2kW-200kHz or 3.0kW-200kHz does LOW＋HIGH：Low freq. - Page 105 ...
-
Page 106: Reference
REFERENCE DIMENSIONAL DRAWING ································································ 98 WIRING DIAGRAM ········································································ 100 CONNECTING DIAGRAM ······························································· 101 CAUTION WHEN OTHER GPS RECEIVER THAN STANDARD SUPPLIED ······································································· 101 IS CONNECTED INSTALLATION OF MAIN UNIT ······················································ 102 INSTALLATION OF MAIN UNIT ONTO DASHBOARD························· 104 INSTALLATION OF TRANSDUCDER ················································ 108 1. -
Page 107: Dimensional Drawing
DIMENSIONAL DRAWING <HE-7301II, HE-7302II> Drawing of holes for installing the bracket ＜ ＞ ... - Page 108 <HE-1501, HE-1502> 99 ...
-
Page 109: Wiring Diagram
WIRING DIAGRAM ... - Page 110 CONNECTOR DIAGRAM CAUTION WHEN NOT STNDARD GPS RECEIVER IS USED ...
-
Page 111: ＜Installation Of Main Unit
※Please install correctly according to following procedure. <HE-7301II, HE-7302II> Procedure of installing main unit】 ＜Installation of main unit＞ 1．＜Decision of place you install＞ While the bracket is mounted with unit, you decide the place you install and put the mark. - Page 112 <HE-1501, HE-1502> Procedure of installing main unit】 ＜Installation of main unit＞ 1．＜Decision of place you install＞ While the bracket is mounted with unit, you decide the place you install and put the mark. ※Keep enough space behind the unit to connect with cables. 2．＜Installation of bracket＞...
-
Page 113: Installation Of Main Unit Onto Dashboard
INSTALLATION OF MAIN UNIT ONTO DASHBOARD Do not install in a simple method. ● It causes to accident like human damage. ※Please install correctly according to following procedure. <10.4 inch models> ... - Page 114 Take off four lids put on holes. Pull them toward front side. Then 2． 3． lids are removed. Put main unit into hole drilled on 4．...
- Page 115 <15 inch models> Please make hole on the panel referring to below dimensional drawing. 1． ...
- Page 116 107 ...
-
Page 117: Installation Of Transducer
INSTALLATION OF TRANSDUCER ●Work on board is too unstable and risky. Installation and maintenance of transducer should be done after you land and fix the boat. Unless you keep it, human damage ... -
Page 118: Installation Of Water Temp. Sensor
INSTALLATION OF WATER TEMP. SENSOR Work on boat is too unstable and risky. ● Installation and temperature of water temperature sensor should be done after you land and fix the boat. Unless you keep it, human damage resulting in serious wound will occur. ... -
Page 119: Standard Composition
STANDARD COMPOSITION 110 ... -
Page 120: Optional Parts
OPTIONAL PARTS ... -
Page 121: General Information Of Fish Finder
GENERAL INFORMATION OF FISH FINDER 112 ... - Page 122 113 ...
-
Page 123: Trouble Shooting
TROUBLE SHOOTING 114 ... - Page 124 115 ...
- Page 125 116 ...
-
Page 126: Specifications
SPECIFICATIONS Display 10.4 inch TFT color LCD Display Style Portrait/Landscape Number of pixel 640 × 480 Operating Voltage DC11V〜35V Dimension Landscape 254.5(H)×268(W)×152(D) mm Portrait 284(H)×268(W)×152(D) mm Weight Approx.4.8ｋｇ Accuracy (Position) 10m（2DRMS）HDOP≦3 (SA off) Accuracy (Speed) 1m/s（RMS）HDOP≦3 (SA off) Receiving Frequency 1,575.42MHz±1MHz Receiving Method... - Page 127 ※Fish Finder is for HE-7301Ⅱ, HE-1501 only. 28, 32/40, 36/65, 40/75, 50, 50/55, 85/90, Frequency （KHz） 200, 50&200 600W、1.2kW、1.8kW、2.5kW、3.0kW Power Output （W） （depends on freq.） Depth Range 0〜2,000m Auto Range OFF／Range／Shift Auto Gain OFF／Low／High A-Mode OFF／ON Fish Alarm OFF／Small／Large Water Temp. Alarm OFF／Within Range／Out of Range Depth Alarm OFF／Within Range／Out of Range...
- Page 128 ...
Need help?
Do you have a question about the HE-7301II and is the answer not in the manual?
Questions and answers