Summary of Contents for McCulloch RS250
- Page 1 McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 www.mcintoshlabs.com RS250 Wireless Loudspeaker System Owner’s Manual Quick Start is on page 4...
-
Page 2: Safety First
Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very It is a smart idea to read all the enclosed RS250 SAFETY (1) this product may not cause harmful interference, and low levels of RF energy that are deemed to comply without INFORMATION included in separate documents;... -
Page 3: Table Of Contents
Spotify Connect ......6 Re-packing the RS250 ....15... -
Page 4: Trademark And License Information
Connect to the RS250 to AC Power • Power the RS250 On by pressing Rear Panel Power The McIntosh RS250 incorporates copyright protected technology that is protected by U.S. patents and other Switch intellectual property rights. The RS250 uses the following Technologies: •... -
Page 5: More Connections
See “Network/Wi-Fi Indicator LED” on page 11. With your mobile device/tablet connected to the RS250 in your house at the same time or adjust the same Wi-Fi network as your RS250 and the RS250 volume in any room – all in sync. -
Page 6: Note About Initial Network Connection
(Figure 10 on page 11). This switch will toggle power below the Right Knob will blink twice, pause and to the RS250 ON (I) and OFF (O). With this switch in aptX™ is a codec that can provide CD quality repeat. -
Page 7: Inputs And Outputs On The Back
“optical audio cable.” The internal digital-to-analog sources. signal. RS250 filters will automatically be optimized converter (DAC) of the RS250 is able to process hi- for integration with an external Subwoofer when For HDMI and Optical volume boost adjustments see res digital audio up to 192kHz/24-bit. The RS250 DAC connected and volume will track accordingly. -
Page 8: Front View Labeled & Installing The Grille
32.4 cm Installing the Grille The RS250’s Grille can be installed by lining up the six plastic pegs on the back of the Grille with the six holes framing the speakers of the RS250. Gently push with even pressure to install and pull straight away from the front to remove the Grille. -
Page 9: Remote Learning
The thicker end will now be the top and most television IR remotes. This is handy to control the you should be staring at the back of the remote. volume of the RS250 that is optically connected to a • Pinch the remote with your index finger resting television with only the television remote. -
Page 10: Description Of Remote Control Buttons
150ms to sync with video. State (power up) The Left Knob The Left Knob can be used to select Selects Previous Track sources, lighting levels, and place the RS250 in Discovery with compatible Selects Next Track Mode. playback sources. with compatible... -
Page 11: Network/Wi-Fi Indicator Led
If a Bluetooth connection is interrupted then it must be re-established from the mobile device. Sleep Mode LED The LED will glow red when the RS250 is connected to a live AC outlet and the unit is in Sleep Mode. When the RS250 receives a power on Rear Connections command, the Sleep Mode LED will turn off. -
Page 12: Hdmi And Optical Gain Adjustment
HDMI input making it louder. • Look for the RS250 in the list of wired or wireless When the Power Sleep Timer is set to ON, the The ability to adjust the volume boost of the Optical... -
Page 13: Figure 11- Overview Submenu
• Wired • Wireless If Network Type is set to Automatic, the RS250 will automatically connect to Wi-Fi when the ethernet cable is unplugged provided the Wireless connection has previously been setup. Selecting Wired for Network Type will limit the RS250 network connection to the ethernet port connection. -
Page 14: Update Menu
McIntosh qualified technician only. lose your Wi-Fi and Bluetooth connection settings. While the RS250 is in the process of updating the An alternative method for Factory Reset, is to Press firmware, the power status LED will blink twice in quick succession, pause for 2 seconds, and then and Hold the Left and Right Knobs for 10 seconds. -
Page 15: Re-Packing The Rs250
Technical Specifications Re-packing the RS250 When shipping the RS250, it is highly recommended Power Output Dimensions that the unit be packed as it was originally shipped to 650W - 400W Tweeter/Mids, 250W Woofers Width 24 13/16 inches (62.99cm) Height 5 11/16 inches (14.48cm) avoid damage. - Page 16 The continuous improvement of its products is the policy of McIntosh Laboratory Incorporated who reserve the right to improve design without notice. The RS250 is designed to employ non-McIntosh-provided services some of which require separate customer subscriptions and some of which do not, as part of the Product’s functionality.