Trackunit TU600A Technical Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

TU600A

Technical Manual

Version 1.1, June 2021

Table of Contents

Need help?

Do you have a question about the TU600A and is the answer not in the manual?

Questions and answers

Summary of Contents for Trackunit TU600A

Page 1: Content
TU600A TU600A Technical Manual Version 1.1, June 2021...
Page 2: Table Of Contents
Power supply ......................14 Digital inputs ....................... 14 Digital output ....................... 14 Motion/acceleration sensor ..................14 Installing the TU600A as to surpass the main switch on the machine......15 Functionality check ..................16 “Verify my Trackunit” ...................... 17 Troubleshooting ................... 18 Installation of the digital output ..............
Page 3 Specific model country approval certificates ..........30 Europe-CEPT ......................... 30 Myanmar ........................30 Japan ..........................30 Australia/New Zealand ....................30 US ..........................30 Canada ........................... 30 Chile ..........................30 Environmental compliance ................31 Trackunit TU600A, Technical Manual v1.1, June 2021 Page 3...
Page 4 (ii) the Product is not modified or misused. This Product countries. All other trademarks are the property of their Limited Warranty shall not apply to, and Trackunit shall not be respective owners. responsible for, defects or performance problems resulting from:...
Page 5 ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY RSS-102, RSS-132, RSS-133, RSS-139. FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE The TU600A product comply with Part 15 of the FCC rules and ABOVE LIMITATION MAY NOT APPLY TO EVERY Industry Canada license exempt RSS standard(s). Operation is RESELLER.
Page 6 RCM mark by SDOC from E7689 Japan certificates: [R] 003-200139 [R] 209-J00306 [T] D200116003 Bluetooth SIG registered: Declaration ID: D046156 Company identifier UUID: 2159 (0x086F) Automotive: KBA UN ECE R10 rev 5/1 certified : Trackunit TU600A, Technical Manual v1.1, June 2021 Page 6...
Page 7: Introduction
Do Not Operate Where Prohibited Do not allow the TU600A unit to operate wherever wireless phone use is prohibited or when doing so may cause interference or danger. The TU600A cannot be turned off after installation, so any vehicle, moving machinery, construction machinery using TU600A etc.
Page 8: Interference
Like all wireless devices, the TU600A may encounter electrical interference that may affect its performance. Avoid Body Contact with Device during Operation Do not operate the TU600A in direct contact with your body. Maintain at least 8 inches (20 cm) separation between the device and any parts of your body. Qualified Service Except for batteries and Subscriber Identification Module (SIM) card, the TU600A contains no user serviceable or replaceable parts.
Page 9: Electronic Devices
TU600A unit and any persons’ body after end user installation. Other Medical Devices If any other personal medical devices are used in the vicinity of a TU600A unit, consult the manufacturers of the medical devices to determine if they are adequately shielded from external RF energy.
Page 10: Posted Facilities
850/1900 MHz BANDS, LTE M1/NB IOT 700/850/1700/1900 MHz bands. The TU600A unit is not intended for handheld use or to be worn on the body. A minimum separation of ten (8”) inches (20 cm) is to be maintained between the TU600A and any persons’...
Page 11: Battery Safety Information
-20°C to 60°C. If the temperature is outside this range the battery is disabled.  When TU600A is operated from an external supply voltage the battery is put into storage from temperatures above +45°C and below -20°C.
Page 12: Delivered Standard Content
1 x Li-ion Battery PN 4233.0002 (May already be mounted inside the TU600A unit) Optional content for generic installation: 1 x Fuse with fuse holder for installation up to 24V DC/ (Max 1A) for TU600A units delivered with open cable ends. For installation in systems with higher voltages than 24V it is recommended to use a fuse and fuse holder rated for the specific supply voltage range, see service chapter for compliant fuse holders.
Page 13: Use Location - Children Not Likely To Be Present
The installation position in multiple equipment/items/vehicles etc. of the same type must be insured to be random to increase the theft protection. It is needed to sign up a different subscription for each installed TU600A unit under insurance coverage that covers the local alarm center administration of the units.
Page 14: Connections
The connections depend on the type of vehicles / machines etc. in which the (GSM/LTE M1/NB IOT)/GPS unit is to be installed. Different variants of the TU600A device will have only a subset of the connections shown in the table below. Please contact your nearest sales office, distributor or “Reseller” for further information about the availability of other variants in your area.
Page 15: Installing The Tu600A As To Surpass The Main Switch On The Machine
The 1-wire input is only operational when supply voltage (12V / 24V / 48V) is present. Interface cannot operate on internal battery alone. Installing the TU600A as to surpass the main switch on the machine. In case the main switch on the machine will break the negative wire (Ground wire), the inputs may register a voltage level and start counting operating hours.
Page 16: Functionality Check
TU600A Functionality check Trackunit TU600A, Technical Manual v1.1, June 2021 Page 16...
Page 17: Verify My Trackunit
TU600A “Verify my Trackunit” In order to control if the installation of the TU600A unit has been done correctly, it is possible to use the “Verify my Trackunit” tool. Trackunit TU600A, Technical Manual v1.1, June 2021 Page 17...
Page 18: Troubleshooting
Check LED status; See the “Functionality check” chapter in this manual.  If the TU600A unit has been delivered with the SIM card mounted. Contact Trackunit support. Or contact the mobile operator to verify if there is any problem with the SIM card.
Page 19: Installation Of The Digital Output
TU600A Installation of the digital output According to the E1 certificate of the TU600A unit, it is prohibited under any circumstances to use this output to control any equipment that may influence the safety of the construction machinery and earth moving machines/vehicle operation and driving. The output must only be used to control comfort equipment.
Page 20: Sms Commands For Output Control
Warranty Trackunit APS products are covered by a limited manufacturer warranty. The Trackunit APS warranty is limited to the warranty rules and legislation present in each country. The warranty only covers manufacturing faults.
Page 21 TU600A For mounting the Trackunit TU600A in harsh environment, not covered by the compliance statements or areas where pressure cleaning is required the Trackunit HW shield PN 7402.9551 is required for protective mounting. Please order at Trackunit APS. Recommended fuse holders and fuses up to 48V supply voltages (Can be ordered at Trackunit APS): a.
Page 22: Minimum Information Required For Technical Assistance
Minimum Information Required for Technical Assistance If you or a user reports difficulty with a TU600A unit (i.e. no GPS fixes, not communicating, LED not working, etc.), it is helpful to retrieve directly from the unit all current configuration settings and the message log data etc., that is accessible by the technical support when they receive the...
Page 23: Internal Temperature Ranges
Internal storage without loss of battery performance -20ºC to +50ºC (Specified by battery cell vendor. This range apply for the TU600A operated from an external DC supply voltage outside the charging temperature range.) Internal storage with loss of battery performance -40ºC to +70ºC...
Page 24  B85: TX 698-716 MHz, RX 728-746 MHz The marked bands B12/B13 are denoted LTE 700 MHz band lower and upper part. The bands B18/B19 are denoted LTE 800 band lower and upper part for Japan. Trackunit TU600A, Technical Manual v1.1, June 2021 Page 24...
Page 25: Mechanical Specifications
Cable length: 170 – 180 cm Environmental class: IP67 (Standalone) IP66K, IP69K (Mounted with HW shield) Enclosure material: Non-flammable PP casing and ABS cable connector lid. Weight: 65 g (excluding the cable) Trackunit TU600A, Technical Manual v1.1, June 2021 Page 25...
Page 26: Approvals And Certificates
“The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Trackunit APS is under license. Other trademarks and trade names are those of their respective owners.” FCC and IC certification statements The TU600A product contains radio transmitters that comply with CFR 47 Part 15, Part 15.247,...
Page 27: Automotive, Off-Road Vehicles, Machinery Etc
Statement for ISO 13849-1 safety 1. The TU600A products are when installed not a vital part in the machine safety system, but it can be used as access control/immobilizer if paired with a keypad (i.e. DualID II), ibutton or wireless (Bluetooth LE enabling).
Page 28: Eu Regulations And Directives
(0 Hz to 300 GHz), when used as intended. o The TU600A product also complies with the essential requirements of the Directive 2014/30/EU for the use of harmonized standards for machinery and vehicles EMC: EN ISO 14982, EN 13309, EN 12895 and ISO 13766-1, -2 ...
Page 29: Ce Marking
Section 134 (1) (g) of the New Zealand Radiocommunications Act 1989, by the Supplier’s Declaration of Conformity (SDOC) Japan  The TU600-15 model of the product family TU600A is approved in Japan with the certificate ID n°: [R] 003-180062, [R] 209-J00306, [T] D180034003 (That contains a Bluetooth Low Energy interface) Trackunit TU600A, Technical Manual v1.1, June 2021...
Page 30: Chile
[R] 209-J00306 [T] D200116003 Australia/New TU600A ACMA/NZ RCM mark by signed SDOC Zealand TU600A FCC ID: ZMF-TU600A Canada TU600A ISED IC: 4796A-TU600A Chile TU600A (NOTE: Label required for compliance to radio law) Trackunit TU600A, Technical Manual v1.1, June 2021 Page 30...
Page 31: Environmental Compliance
TU600A Environmental compliance The TU600A are designed for compliance to the following environmental standards related to the intended use of the product: Standard Version Description A, B SAEJ1455:2017, EN/IEC 60068-2-1 2007 Cold SAEJ1455:2017, EN/IEC 60068-2-2 2006 Dry Heat IEC 61373, SAEJ1455:2017,...
Page 32 TU600A Environmental protection without HW shield: Trackunit TU600A, Technical Manual v1.1, June 2021 Page 32...
Page 33 TU600A Environmental protection with use of HW shield: Trackunit Aps Gasvaerksvej 24, 4 sal DK-9000 Aalborg Denmark Trackunit TU600A, Technical Manual v1.1, June 2021 Page 33...

This manual is also suitable for:

4520202