Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Grange 3m LDT
Summary of Contents for Grange 3m LDT
- Page 1 3m LDT (Low Disturbance Toolbar) Operator Manual VAT No: 256 156 792 Manual reference: GM/3mLDT/Iss1.0 Grange Machinery Ltd. M: 07918 515385 Sproatley Grange T: 01482 815711 Hull E: rjones@grangemachinery.co.uk HU11 4PT W: www.grangemachinery.co.uk...
-
Page 2: Table Of Contents
1.1 Introduction to the Grange 3m LDT 1.2 Meanings and definitions 2.0 Safety considerations during the machines life cycle 3.0 Check your own working systems! 3.1 Risk assessment for use of Grange 3m LDT across its intended lifecycle 4.0 Safety decals 5.0 Equipment specifications 5.1 Rear attachments 6.0 Lifting and slinging of Grange 3m LDT. -
Page 3: Identification Of Manual
Machines life cycle the manufacturer to its end of operational life and subsequent The serial plate is located on the headstock of the Grange 3m LDT, as detailed in the photo below. authorised disposal. The hazard symbol is used throughout the manual to highlight areas of importance to the operator. -
Page 4: Safety Considerations During The Machines Life Cycle
Can the operator seek advice on operational parameters for the Grange 3m LDT equipment from other persons when working remotely in the field? vi. When performing any adjustments to the Grange 3m LDT and any 2nd stage cultivation/seeding equipment, the tractor engine must be turned off, the key removed and handbrake applied to prevent the hydraulics from operating. -
Page 5: Risk Assessment For Use Of Grange 3M Ldt Across Its Intended Lifecycle
MEDIUM area Contact Grange Machinery Ltd The operation and use of the Grange 3m LDT presents a low level of for replacement components if risk. any damage occurs to lifting & slinging eyes. Please note; some hazards may occur during operation with the use... -
Page 6: Safety Decals
Undertaking inspection and maintenance and replacement of wearing part procedures on the Grange 3m LDT equipment. Table 1.0 summarises the safety decals in use on the Grange 3m LDT and their meanings. The colour definitions for the decals are as follows;... -
Page 7: Rear Attachments
6.0 Lifting and slinging of Grange 3m LDT only 2nd stage cultivation / seeding equipment which complements the use of the The Grange 3m LDT range includes two lifting eyes (Ref fig 1.0) for use with Grange 3m LDT in tillage practices. -
Page 8: Storage Of Machinery When Not In Use
When going from the transport mode to working mode for the Grange 3m LDT always make sure no people are in distance of been hurt or trapped. -
Page 9: Hydraulic Services To Operate The Grange 3M Ldt
8.2 Hydraulic services to operate the Grange 3m LDT CAT IV LOWER LINK COUPLING CAT III TOP LINK POSITION CAT III LOWER LINK COUPLING CAT IV TOP LINK PIN 2 X DOUBLE ACTING HYDRAULIC SERVICES TO OPERATE AND FUNCTION THE GRANGE 3M LDT... -
Page 10: Disc Rams - Depth Control
¾ INCH FREE FLOW RETURN ARM ATTACHMENT STRAPPING POINT FOR USE 7 PIN LIGHTING SOCKET WHEN TRANSPORTING GRANGE 3M LDT ON TRANSPORT TRAILER LIGHTING AND HYDRAULIC SERVICE REAR LINK ARM HITCH FOR BACK PLATE AND WHERE APPLICABLE COUPLING UP 2ND STAGE... -
Page 11: Attachment Option
The diagram and example calculation in Fig 4.0 demonstrates the values which need to be established. Note the value d [m] is taken from the centre of the linkage balls to the centre of the lifting eyes (e.g. the Grange 3m LDT centre of gravity) -
Page 12: Setting Up Machine For Work
20mm). Ensure that the linkage balls are not corroded and can turn on the pins. ballast The correct top link setting is important to ensure the Grange 3m LDT is safe and Combined mass of front mounted implement / efficient in operation, ref Fig 5.0. -
Page 13: Clevis Hitch
When connecting 2nd stage cultivation/seeding equipment; activate the of gravity and Fig 10.0 illustrates the Grange 3m LDT once the link arm tractor auxiliary hydraulics to lift the Grange 3m LDT main beam and hitch has been removed. -
Page 14: Transport Safety
The The legislation which covers the transportation of the Grange 3m LDT Grange 3m LDT is now setup in the working position, ref fig 11.0. Stop the equipment on the UK public highway when coupled to the tractor movement controls of the tractor, apply the handbrake, stop the engine and is The Construction and Road Use Regulations (C&U) 1986. -
Page 15: Headland Turns And Working Sequence
Maintain activation of the auxiliary hydraulics to rotate the cutting discs into work. Please note! i. Never try turning bends with the Grange 3m LDT legs in the ground. ii. Always lift the legs out of working position before turning on headlands or short turns. -
Page 16: Replacing Shear Bolts
3m LDT with appropriate axle stands to enable safe same size fixing. Ensure the bolt is fully tightened, the Grange 3m LDT. If requiring the 3m LDT machine to be raised access to the points. Please be aware it is forbidden ref Fig 17.0. -
Page 17: Troubleshooting
16.0 End of life recycling Check tractor tyre pressures and front ballast. The Grange 3m LDT is manufactured from components have been in contact with hydraulic oil predominantly steel components with hydraulic they will need to be disposed of via an appropriate If required refer to Grange Machinery Ltd pipes and activating rams. -
Page 18: Spare Parts Listing
17.0 Spare parts listing 17.2 Fig 17.0 Hydraulic schematic of Grange 3m LDT PART NUMBER DESCRIPTION WING WIDTH Legend SP-0028 Narrow Point 40mm 1. Main Beam Lifting Ram 30/60/200CB 3. Disc ram 30/60/100CB 2. Pilot Operated Check Valve 4. Port Mounted Pilot Operated Check Valve (3/8” POC) -
Page 19: Warranty
Grange 3m LDT attached and also a 2nd stage cultivation/ seeding equipment with a drawbar load of 2500kg. The clevis hitch on the Grange 3m LDT is located at approximately the same position as the units centre of gravity. Please note these are indicative calculations... - Page 20 Notes Notes Grange Machinery Ltd. M: 07918 515385 Grange Machinery Ltd. M: 07918 515385 Sproatley Grange T: 01482 815711 Sproatley Grange T: 01482 815711 Hull E: rjones@grangemachinery.co.uk Hull E: rjones@grangemachinery.co.uk HU11 4PT W: www.grangemachinery.co.uk HU11 4PT W: www.grangemachinery.co.uk...
- Page 21 Notes Grange Machinery Ltd. M: 07918 515385 Sproatley Grange T: 01482 815711 Hull E: rjones@grangemachinery.co.uk HU11 4PT W: www.grangemachinery.co.uk...
Need help?
Do you have a question about the 3m LDT and is the answer not in the manual?
Questions and answers