Summary of Contents for Chapman Machinery MGF350
- Page 1 MGF350 Mounted Game Feeder Original Instructions Chapman Machinery Ltd, Hele Barton, Week St. Mary, Holsworthy, Devon EX22 6XR Tel: 01288 308149 Email: sales@chapman.co.uk...
-
Page 2: Table Of Contents
The information contained in this manual is correct at the time of going to press. However, in the course of development, changes in specification are inevitable. Should you find the information given differs from your machine, please contact Chapman Machinery Ltd direct for advice. Use only Chapman Genuine Service Parts on Chapman Machinery and Machines... -
Page 3: Hse Information
HSE Information Safe use of all-terrain vehicles (ATVs) in agriculture and forestry – AIS Sheet 33 Remember that your ability to control the ATV by your body Introduction movements will be considerably reduced when carrying a load or towing a trailer. This information sheet gives advice on the safe use of ATVs. -
Page 4: Important Safety Information
Important Safety Information Always read this manual before fitting or operating the machine – whenever any doubt exists contact your dealer or the Chapman Machinery Service Department for advice and assistance. DEFINITIONS The following definitions apply throughout this manual: WARNING - An operating procedure, technique etc., which can result in personal injury or loss of life if not observed carefully. -
Page 5: Description
Description The MGF350 Mounted Game Feeder is designed for feeding a variety of feedstuffs to game birds such as pheasants, partridges and guinea fowl. Operating with an electric spinner motor and electric shutter, ensuring accurate disposition. The rotor and wiring mechanism are all IP67 rated, to ensure trouble-free usage in even the toughest winter conditions. -
Page 6: Attachment
Component Identification PVC Tonneau Cover Simple Control Fork lift loading Drop Size Slots calibration Spinning Plate Attachment Before Attaching the Machine Before attachment, ALWAYS ensure the following: - The carrying vehicle has sufficient capacity for the fully laden unit (Machine weight circa 90kg + Max feed capacity (varies with feed used, this must be checked!) = total laden weight - All safety guards &... -
Page 7: Attaching The Machine
Attaching the Machine NOTE: This machine is designed to attach to the carrying vehicle using 4 x ratchet straps. Never use less than 4 straps to secure the load as movement may result! Remove tailgate from carrying vehicle. Load MF350 into bed using forklift slots or suitable lifting strops rated to carry plated unladen weight. - Page 8 Centralise hopper in bed and attach using 4 x supplied ratchet straps, 2 straps per side. Ratchet straps must be fitted in a crossing manner as shown below! It is the user’s responsibility to ensure the unit is securely fitted in the bed. Fit the cover support bar to prevent the cover sagging as shown below.
-
Page 9: Initial Calibration
Initial Calibration On the RH Side at the rear of the machine you will find two black handwheels and an indicator plate as shown below. Initially set the Feed adjustment plate to setting 2, as indicated by the arrow on the drop adjustment plate. -
Page 10: Control Box
Control Box The control box on the MGF350 is a simple switched system with relays, as shown below. The LH switch opens and closes the shutter, and the RH switch turns the main spinner on and off. Specification Supply Voltage: 12V DC nominal, 16V MAXIMUM Power... -
Page 11: Operating Limits & Recommendations
Operating Limits & Recommendations Ensure that the operator is suitably qualified to use a machine of this nature and that they have fully read and understood this manual - they should be aware of all safety aspects relating to the safe use of the machine. -
Page 12: Troubleshooting
Troubleshooting Problem Possible Causes Remedies Low Supply Power Charge Battery Incorrect Polarity / poor Check connection connection Unit will not operate Fuse Blown Check fuse in control box Control Box Fault Contact distributor / Chapman Spinner Motor does not Main Fuse Blown Replace main motor fuse operate even though shutter is working... -
Page 13: Warranty
The Chapman warranty be transferred to a subsequent owner of the machinery (for use within the UK only) for the balance of the warranty period subject to all of the stated warranty conditions and provided that the Change of Owner form is completed and sent to Chapman Machinery within 14 days of change of owner- ship. - Page 14 Hele Barton Week St. Mary Holsworthy Devon EX22 6XR The Products Covered by this Declaration Product: MGF350 Trailed Game Feeder & Options (Off-Highway) Standards and Regulations used: Machinery Directive 2006/42/EC Place of Issue: United Kingdom Name of Representative: James Chapman...