Freestyle Dive 75401 Instructions Manual page 2

to any time outside it, then set the date
and then reset to the correct time.
TO USE THE CHRONOGRAPH (STOP-
WATCH):
1. Press S1 button to start counting.
2. To stop counting, press S1 button once.
Press S1 button again to resume from
where it left off.
3. To reset to zero, press S1 button to stop
counting and then press S2 button.
1. Hour Hand
2. Minute Hand
3. Second Hand
4. 24 Hour Hand
5. Chronograph Minute Hand
6. Chronograph Second Hand
7. Calendar
S1 – Chronograph start/stop button
S2 – Chronograph split/split release/
reset button
TO ADJUST THE CHRONOGRAPH HANDS
POSITION:
Before setting the time, check if the
Chronograph Second Hand and Chrono-
graph Minute Hand are at the 12 o'clock
position.
If the chronograph is in use, press the
button in the following order to reset it,
and then check if the chronograph hands
have returned to 12 o'clock position.
If the chronograph is counting: S1 S2
If the chronograph is stopped: S2
If the split time is displayed:
IIn case one or several chronograph
hands are not at the 12 o'clock position
due to certain reasons (e.g. follow-
ing a battery change), that needs to be
adjusted.
1. Pull crown out to second click
position C.
2. Press S1 or S2 button to set the
Chronograph Second Hand and
Chronograph Minute Hand (me
chanically coupled). By pressing S1 or
S2 button, the hands will move
counter-clockwise or clockwise
respectively.
3. Push crown back to position A.
TO SET THE TIME:
1. Pull crown out to second click position
C.
2. Turn crown to set time.
3. Push crown back to position A.
NOTE: The 24 Hour Hand will also be set
during time setting.
TO SET THE DATE:
1.Pull crown out to first click position B.
2.Turn crown clockwise to set date.
3.Push crown back to position A.
NOTE: Do not set the date between 9:00
P.M. and 1:00 A.M. Otherwise, the date
may not change properly on the following
day. If it is necessary to set the date dur-
ing that time period, first change the time
to any time outside it, then set the date
and then reset to the correct time.
TO USE THE CHRONOGRAPH (STOP-
WATCH):
For the measurement of elapsed time,
1. Press S1 button to start counting.
2. To stop counting, press S1 button once.
Press S1 button again to resume from
where it left off.
3. To reset to zero, press S1 button to stop
counting and then press S2 button.
For the measurement of split time,
1. Press S1 button to start counting.
2. While the chronograph is running,
press S2 button once to register a lap.
The chronograph is still running in the
background.
To display the currently accumulated
time, press S2 button again. The chro-
nograph hands will quickly advance to
the ongoing measured time.
3. Repeat the last step until all the laps
have been registered.
4. To reset to zero, press S1 button to stop
counting and then press S2 button.
NOTE: The chronograph is able to mea-
sure up to 60 minutes.
TO USE THE BACKLIGHT:
Some watch models are equipped with an
electroluminescence (EL) backlight. To
turn on the backlight, press the backlight
button.
If there is no separate backlight button,
press the crown to activate the backlight.
SCREW-DOWN CROWN
Some watch models are equipped with
a screw-down crown. Make sure to un-
screw the crown before pulling out the
crown for setting, then screw the crown
back in tightly after setting to avoid any
water entry.
S2 S1 S2
ENGLISH
To reduce carbon foot print, these
Freestyle instructions are printed with
soy inks on recycled paper.