Summary of Contents for Smarteh LPC-2.CR1
- Page 1 USER MANUAL Longo programmable controller LPC-2.CR1 Card Reader module Version 5 SMARTEH d.o.o. / Poljubinj 114 / 5220 Tolmin / Slovenia / Tel.: +386(0)5 388 44 00 / e-mail: info@smarteh.si / www.smarteh.si...
- Page 2 Longo programmable controller LPC-2.CR1 Written by SMARTEH d.o.o. Copyright © 2016, SMARTEH d.o.o. User Manual Document Version: 005 June, 2016...
- Page 3 Vibrations and climatic-mechanical: EN 60068-2-6, EN 60068-2-27, • EN 60068-2-29 Smarteh d.o.o. operates a policy of continuous development. Therefore we reserve the right to make changes and improvements to any of the products described in this manual without any prior notice.
-
Page 4: Table Of Contents
Longo programmable controller LPC-2.CR1 Longo programmable controller LPC-2.CR1 1 ABBREVIATIONS................1 2 DESCRIPTION...................2 3 FEATURES..................3 4 OPERATION..................4 4.1 Parameters................4 5 INSTALLATION..................5 5.1 Connection scheme..............5 5.2 Mounting instructions..............7 5.3 Module labeling................8 6 TECHNICAL SPECIFICATIONS..............9 7 SPARE PARTS..................10 8 CHANGES ..................11 9 NOTES..................12... -
Page 5: Abbreviations
Longo programmable controller LPC-2.CR1 1 ABBREVIATIONS Sorted by order of appeareance in document: RFID Radio frequency identification Emergency call Light emitting diode Dual in-line package Identity Main control unit... -
Page 6: Description
Longo programmable controller LPC-2.CR1 2 DESCRIPTION LPC-2.CR1 RFID reader is intended to be used as an identity verification device for room, office or other indoor entrance. When RFID tag (key-card) is approached to the reader and its code is successfully read out, the green LED blinks and a short beep is generated. -
Page 7: Features
Longo programmable controller LPC-2.CR1 3 FEATURES Figure 1: LPC-2.CR1 module. Table 1: Technical data RFID reader OK “ √ ” LED Fault “ X ” LED Power LED Internal fault LED Internal built-in buzzer Black or white glass possibility... -
Page 8: Operation
Longo programmable controller LPC-2.CR1 4 OPERATION Operation of the CR1 module is also dependent on parameters received on RS-485 communication channel. Reader RFID field is active always when module is powered up. If tag is put inside RFID field, reader tries to resolve RFID tag code. -
Page 9: Installation
Longo programmable controller LPC-2.CR1 5 INSTALLATION 5.1 Connection scheme Figure 2: Connection scheme... - Page 10 Longo programmable controller LPC-2.CR1 Table 2: K1 K1.1 Ground K1.2 10 .. 24 V DC Power supply input K1.3 RS-485 A Data receive/send line A K1.4 RS-485 B Data receive/send line B Table 3: LEDs & Buttons ON: RFID key standard NOK or ID card number wrong LED1: red Fault “...
- Page 11 Master ● Frames of other vendors most probably suits as well, but they were not verified by Smarteh. Before installation verify compatibility of non listed frames. Module housing has a fin on each side, which can be easily removed with knife cutter or pliers. This adaptation enables housing to be build in various frame formats with two different depths.
-
Page 12: Mounting Instructions
RFID panel should not be positioned close to conductive areas. 1. Set the correct RS-485 address (S1 switch) for LPC-2.CR1 (refer to the Table 4). 2. Connect interconnection cable to the connector K1. Max. allowed tractive force is 30 N. -
Page 13: Module Labeling
Label 2 descriptions: 1. S/N: CR1-S9-1000000003 is the serial number. CR1 – short product name, • S9 – user code (test procedure, e.g. Smarteh person xxx), • 1000000003 – year and current stack code, • 10 – year (last two cyphers), •... -
Page 14: Technical Specifications
Longo programmable controller LPC-2.CR1 6 TECHNICAL SPECIFICATIONS Table 6: Technical specifications Power supply from MCU Interconnection connector type RJ-12 6/6 Power consumption 1.5 W EM4100, 125 kHz, Manchester 64, read only RFID type HITAG2 UID, read only Max. reading distance... -
Page 15: Spare Parts
Longo programmable controller LPC-2.CR1 7 SPARE PARTS For ordering spare parts following Part Numbers should be used: LPC-2.CR1 Card Reader module LPC-2.CR1, EM, black P/N: 225CR109V01001 LPC-2.CR1 Card Reader module LPC-2.CR1, EM, white P/N: 225CR115V01W01 LPC-2.MC8 Main module LPC-2.MC8 P/N: 225MC813001001... -
Page 16: Changes
Longo programmable controller LPC-2.CR1 8 CHANGES The following table describes all the changes to the document. Date Description 07.06.2016 General update. 01.06.2014 Power consumption data update. 01.02.2013 Technical update. 01.07.2012 CGP General update. 18.03.2010 The initial version, issued as LPC-2.CR1 module UserManual. -
Page 17: Notes
Longo programmable controller LPC-2.CR1 9 NOTES...
Need help?
Do you have a question about the LPC-2.CR1 and is the answer not in the manual?
Questions and answers