Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Celectron Audio SW110A
Summary of Contents for Celectron Audio SW110A
- Page 1 SW110A - SW115A - SW118A Active Subwoofer USER MANUAL...
- Page 3 FCC COMPLIANCE NOTICE This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
-
Page 4: Table Of Contents
DIMENSIONS AND FLYING POINTS ... . . 4 SW110A CONTROL PANEL (FIG.1) ... . . 7 SW115A / SW118A CONTROL PANEL (FIG.2)..7 CONNECTIONS (FIG.3) . -
Page 5: Technical Specifications
520 x 330 x 350 mm * Rated consump on is measured with pink noise with a crest factor of 12 dB, this can be considered a standard music program. FREQUENCY RESPONSE SW110A (100/160 Hz filter) SW115A (100/160 Hz filter) 100 Hz FILTER... -
Page 6: Dimensions And Flying Points
DIMENSIONS 52 cm 20.5 " SW110A 35 cm 13.8" M8 Flying Point M8 Flying Point Handle Moun ng Pole M8 Flying Point M8 Flying Point... - Page 7 SW118A Pole adapter 74 cm SW115A 29.1" 43 cm 60 cm 23.6" 16.9" POLE ADAPTER 70 cm 27.6"...
- Page 8 SW110A - CONTROL PANEL (FIG.1)
-
Page 9: Sw110A Control Panel (Fig.1)
SW115A / SW118A - CONTROL PANEL (FIG.2) CONNECTIONS (FIG.3) tip - hot ring - cold cold sleeve - ground ground INPUT INPUT Jack (balanced) Balanced male XLR ground tip - hot cold cold ground INPUT OUTPUT / LINK Jack (unbalanced) Balanced female XLR *note: connect both cold and ground to make cable from balanced to unbalanced... - Page 10 SW110A - CONFIGURATIONS (FIG.4) LEFT RIGHT LT6A LT6A SW110A (sub) basic SUB+SAT system 1x SW110A 2x LT6A LEFT RIGHT 2x LT6A 2x LT6A SW110A (sub) double sat SUB + 2 SAT system 1x SW110A 4x LT6A LEFT RIGHT LT8A LT8A...
-
Page 11: Configurations (Fig.4)
SW115A / SW118A - CONFIGURATIONS subwoofer reinforcement Subwoofer output of analog or digital PHASE must be the loudspeaker processor same for all subs RIGHT LEFT LT8A LT8A basic stereo system set the PHASE switch to obtain the louder bass level 1x SW115A 2x LT8A RIGHT LT12A... -
Page 12: Safety And Precautions
SAFETY AND PRECAUTIONS • CAUTION: before using this product read carefully the following safety instructions. Take a look of this manual entirely and preserve it for future reference. When using any electric product, basic precautions should always be taken, including the following: –... -
Page 13: Ce Conformity
CE CONFORMITY • CELECTRON products comply with directive EMC 2014/30/CE, as stated in EN 55103-1 and EN 55103-2 standards and with directive LVD 2014/35/CE, as stated in EN 60065 standard. • Under the EM disturbance, the ratio of signal-noise will be changed above 10dB. PACKAGING, SHIPPING AND COMPLAINT •... -
Page 14: General Information
All the modules include a STEREO pre-amp sec on, 24dB/oct. crossover filters with selectable frequency and PHASE reverse switch. The SW110A cabinet is built with 15 plywood and feature metal handle for an easy transport. INSTRUCTIONS ( FIG. 1 / 2 / 3 ) 1. - Page 15 Here’s where you plug in your satellite speaker’s mains supply cord. Connec ng the satellite speaker to this socket you can switch on/off the whole system from the SW110A power switch. WARNING: the maximum load for each socket is 4 amperes, the power out sockets are NOT protected by the...
- Page 16 Celectron Electronic Group BBFY Industrial USA Inc City of Industry - California www.celectronaudio.com...