Summary of Contents for Heatmiser PRT/HW-WTS
- Page 1 Heatmiser PRT/HW-WTS Wireless Programmable Thermostat with Hot water output Ref: PRT/HW-WTS Rev: 1.0...
-
Page 2: Table Of Contents
Contents Page Installation Procedure Pairing the Thermostat with the Receiver Temperature Display Setting the Clock Comfort Levels Explained Hot Water Timings Explained Changing the Hot Water Times Locking the Thermostat Temperature Hold & Override Holiday Heat On/Off Clean Screen Factory Reset Calibration Recharging the Battery Optional Feature Setup... -
Page 3: Installation Procedure
Installation Procedure Do’s Do mount the thermostat at eye level, or if using the desk stand, ensure the thermostat is away from any heat sources. Don’ts Do not push hard on the LCD otherwise you will damage the liquid crystal display and this is not repairable. Wall mounting The wall plate is supplied loose. -
Page 4: Pairing The Thermostat With The Receiver
Pairing the Thermostat To pair the thermostat with the receiver, follow these steps; On the receiver; Press the Pair button. The Communication LED will come on On the thermostat; Press Prog and then Setup At the top of the LCD, you will see 01. Use the up arrow to select 05 to enter the pairing function ... -
Page 5: Temperature Display
Note: You need to finish pairing the thermostat before the receiver pair LED goes out. Pair Successful The Comms LED on the receiver should flash and then go out to indicate the pair is successful. The thermostat will then display the communication icon. -
Page 6: Setting The Clock
Setting the Clock To set the clock in your thermostat, follow the steps below; With the thermostat turned on, press PROG Press Clock Use the Up and Down keys to set the correct time Press Day to set the correct day ... - Page 7 Factory Programmed Comfort Levels The following comfort levels are programmed already, however you can change them easily. Weekday Level Time Temp Wake 07.00 21°C Leave 09.00 16°C Return 16.00 21°C Sleep 22.00 16°C Weekend Level Wake 09.00 21°C Leave 22.00 16°C Return --.--...
-
Page 8: Hot Water Timings Explained
When complete, press Done to store and exit. Hot Water Timings Explained The PRT/HW-WTS offers an additional timed output for the hot water cylinder. The thermostat offers 5/2 Day Programming (4 Levels for the Weekday, 4 for the Weekend) and 7 day Programming (4 Levels... -
Page 9: Changing The Hot Water Times
Factory Programmed Hot Water Times The following hot water switching times are programmed already; however you can change them easily. Weekday On Time Off Time 07:00 09:00 16:00 20:00 --.-- --.-- --.-- --.-- Weekend On Time Off Time 07:00 09:00 16:00 20:00 --.--... -
Page 10: Locking The Thermostat
Changing the Hot Water Times Press Prog and select Timer You will see Time 1 and On Flash Use the Up/Down keys to set the time for the 1 switching time Press Off and then use the Up/Down keys to set the off switching time. -
Page 11: Temperature Hold & Override
Temperature Set Using the Up and Down keys allows you to adjust the set temperature. When you press either of these keys, you will see the word SET and the desired temperature. Press Done to accept. Temperature Hold The temperature hold function is ideal for parties or when you will be going out for a number of hours. -
Page 12: Holiday
Hot Water Override The thermostat has an override function for the hot water output, allowing you to override the hot water into the opposite state. Press Hold Press Timer If the Hot water is already on, press OFF ... - Page 13 Assume you program a holiday on Monday for 1 day, the holiday will start immediately will count the next day (Tuesday) as the holiday. The thermostat will then revert back to its program at midnight at midnight Tuesday. Press Holiday ...
-
Page 14: Heat On/Off
Thermostat Off: To turn the thermostat off completely, press and hold the Power Button. The display and heating will be turned off. To turn the thermostat back on, press the Power button. Clean Screen Pressing “Screen” will disable all buttons, allowing you 15 seconds to wipe the screen clean. -
Page 15: Calibration
Calibration Should you need to calibrate the thermostat, follow these steps; Turn off the thermostat Press and hold the OFF Key for 10 seconds Use the Up and Down keys to enter the correct temperature. Press Done to store Battery and Recharging The thermostat battery should last at least 6 months in normal... -
Page 16: Optional Feature Setup
Feature Setup Feature 01 – Temperature Format: This function allows you to select between °C or °F Feature 02 – Switching Differential: This function allows you to adjust the switching differential of the thermostat. This is the number of degrees the thermostat will switch on below the set temperature. This can be adjusted in order to obtain optimum switching of the heating in your home. - Page 17 Feature 04 – Output Delay: To prevent rapid switching, an output delay can be entered. This can be set from 00-15 minutes. The default is 00 which means there is no delay. Feature 05 – Pairing Function: Allows the thermostat to be paired with the receiver.
- Page 18 Feature 07 – Optimum Start: Optimum start will bring the heating on early if needed, so the house is warm when you wake up. This means you don’t need to allow any extra heat up time when programming the comfort levels. The thermostat will automatically learn the required heat up time and will adjust itself, if required, throughout the year.
- Page 19 Adjusting the Feature Settings To adjust the settings, follow these steps; With the thermostat turned on. Press Prog Press Setup Use the Up/Down keys at the top of the screen to select the feature number (Shown on page 16) ...
- Page 20 Feature Table Feature Description Setting Temperature Format Switching 0.5 – 03 Differential 1°C Default Frost Protect 07-17°C Temperature 12°C Default Output Delay 00-15 Minutes 00 Default Pairing Used to Pair with Receiver Fail Safe 00 Disabled 01 Enabled (00 default) Preheat 00-03 Hours 00 Default...
- Page 21 Support: 01254 870303...